convert the binding file extcon-usbc-cros-ec.txt to
yaml format extcon-usbc-cros-ec.yaml

This was tested and verified on ARM with:
make dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml
make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml

Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

The older compatible variant of this chip is called FSA880
and works the same way, if we need some quirks in the future,
it is good to let it have its own compatible string.

Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

This patch adds documentation for binding of extcont Fairchild
Semiconductor FSA9480 microusb switch.
This usb port accessory detector and switch, can be found for example in
some Samsung s5pv210 based phones.

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

PTN5150 is a small thin low power CC (Configurationn Channel)
Logic chip supporting the USB Type-C connector application with
CC control logic detection and indication functions.

Signed-off-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
[cw00.choi: Fix bulid dependency and clean-up code]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>

This patch add documentation for binding of USB Type C cable detection
mechanism is using EXTCON subsystem. The device can detect the presence
of display out but it may also detect other external accessories when
external accessories is attached or detached.

Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Driver can now work with both ID and VBUS pins or either one of
them.

There can be the following 3 cases

1) Both ID and VBUS GPIOs are available:

ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB state is same as VBUS.

2) Only ID GPIO is available:

ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB active

3) Only VBUS GPIO is available:

VBUS = LOW -> USB_HOST inactive, USB inactive
VBUS = HIGH -> USB_HOST inactive, USB active

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Some Qualcomm PMICs have a misc device that performs USB id pin
detection via an interrupt. When the interrupt triggers, we
should read the interrupt line to see if it has gone high or low.
If the interrupt is low then the ID pin is grounded, and if the
interrupt is high then the ID pin is being held high.

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
[cw00.choi: Edited the driver description and added the author information]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Update the binding documentation to mention the defines added for the
possible values of wlf,gpsw.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>