| Age | Commit message (Collapse) | Author |
|---|
|
The synchronous message API in usbcore (usb_control_msg(),
usb_bulk_msg(), and so on) uses uninterruptible waits. However,
drivers may call these routines in the context of a user thread, which
means it ought to be possible to at least kill them.
For this reason, introduce a new usb_bulk_msg_killable() function
which behaves the same as usb_bulk_msg() except for using
wait_for_completion_killable_timeout() instead of
wait_for_completion_timeout(). The same can be done later for
usb_control_msg() later on, if it turns out to be needed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/linux-usb/3acfe838-6334-4f6d-be7c-4bb01704b33d@rowland.harvard.edu/
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/248628b4-cc83-4e81-a620-3ce4e0376d41@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for responding to Sink Cap Extended msg request. To achieve
this, include parsing support for DT properties related to Sink Cap
Extended. The request for Sink Cap Ext is a control message while the
response is an extended message (chunked). As the Sink Caps Extended
Data Block size (24 Byte) is less than MaxExtendedMsgChunkLen (26 Byte),
a single chunk is sufficient to complete this AMS.
Supporting sink cap extended messages while responding to a
Get_Sink_Caps_Extended request when port is in Sink role is required in
order to be compliant with at least USB PD Rev3.1 Ver1.8.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260223-skedb-v2-2-60675765bc7e@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Elan touchscreens have a HID-battery device for the stylus which is always
there even if there is no stylus.
This is causing upower to report an empty battery for the stylus and some
desktop-environments will show a notification about this, which is quite
annoying.
Because of this the HID-battery is being ignored on all Elan I2c and USB
touchscreens, but this causes there to be no battery reporting for
the stylus at all.
This adds a new HID_BATTERY_QUIRK_DYNAMIC and uses these for the Elan
touchscreens.
This new quirks causes the present value of the battery to start at 0,
which will make userspace ignore it and only sets present to 1 after
receiving a battery input report which only happens when the stylus
gets in range.
Reported-by: ggrundik@gmail.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221118
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Flags are boolean values, hence they should be typed
as bool, not as u8.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20260210122208.29244-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Chasing vfork()'ed tasks on a CID ownership mode switch requires a full
task list walk, which is obviously expensive on large systems.
Avoid that by keeping a list of tasks using a mm MMCID entity in mm::mm_cid
and walk this list instead. This removes the proven to be flaky counting
logic and avoids a full task list walk in the case of vfork()'ed tasks.
Fixes: fbd0e71dc370 ("sched/mmcid: Provide CID ownership mode fixup functions")
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260310202526.183824481@kernel.org
|
|
A newly forked task is accounted as MMCID user before the task is visible
in the process' thread list and the global task list. This creates the
following problem:
CPU1 CPU2
fork()
sched_mm_cid_fork(tnew1)
tnew1->mm.mm_cid_users++;
tnew1->mm_cid.cid = getcid()
-> preemption
fork()
sched_mm_cid_fork(tnew2)
tnew2->mm.mm_cid_users++;
// Reaches the per CPU threshold
mm_cid_fixup_tasks_to_cpus()
for_each_other(current, p)
....
As tnew1 is not visible yet, this fails to fix up the already allocated CID
of tnew1. As a consequence a subsequent schedule in might fail to acquire a
(transitional) CID and the machine stalls.
Move the invocation of sched_mm_cid_fork() after the new task becomes
visible in the thread and the task list to prevent this.
This also makes it symmetrical vs. exit() where the task is removed as CID
user before the task is removed from the thread and task lists.
Fixes: fbd0e71dc370 ("sched/mmcid: Provide CID ownership mode fixup functions")
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260310202525.969061974@kernel.org
|
|
Requested by Maxime Ripard for drm-misc-next because renesas people need
fb797a70108f ("drm: renesas: rz-du: mipi_dsi: Set DSI divider").
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
|
|
After sparc64, there are no remaining users of ARCH_CLOCKSOURCE_DATA
and it can just be removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: John Stultz <jstultz@google.com>
Link: https://patch.msgid.link/20260304-vdso-sparc64-generic-2-v6-14-d8eb3b0e1410@linutronix.de
[Thomas: drop sparc64 bits from the patch]
|
|
Allocating the data pages as part of the kernel image does not work on
SPARC. The MMU will raise a fault when userspace tries to access them.
Allocate the data pages through the page allocator instead.
Unused pages in the vDSO VMA are still allocated to keep the virtual
addresses aligned. Switch the mapping from PFNs to 'struct page' as that is
required for dynamically allocated pages. This also aligns the allocation
of the datapages with the code pages and is a prerequisite for mlockall()
support.
VM_MIXEDMAP is necessary for the call to vmf_insert_page() in the timens
prefault path to work.
The data pages need to be order-0, non-compound pages so that the mapping
to userspace and the different orderings work.
These pages are also used by the timekeeping, random pool and architecture
initialization code. Some of these are running before the page allocator is
available. To keep these subsytems working without changes, introduce
early, statically data storage which will then replaced by the real one as
soon as that is available.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Christophe Leroy (CS GROUP) <chleroy@kernel.org>
Link: https://patch.msgid.link/20260304-vdso-sparc64-generic-2-v6-3-d8eb3b0e1410@linutronix.de
|
|
GPU use-cases for mmu_interval_notifiers with hmm often involve
starting a gpu operation and then waiting for it to complete.
These operations are typically context preemption or TLB flushing.
With single-pass notifiers per GPU this doesn't scale in
multi-gpu scenarios. In those scenarios we'd want to first start
preemption- or TLB flushing on all GPUs and as a second pass wait
for them to complete.
One can do this on per-driver basis multiplexing per-driver
notifiers but that would mean sharing the notifier "user" lock
across all GPUs and that doesn't scale well either, so adding support
for multi-pass in the core appears to be the right choice.
Implement two-pass capability in the mmu_interval_notifier. Use a
linked list for the final passes to minimize the impact for
use-cases that don't need the multi-pass functionality by avoiding
a second interval tree walk, and to be able to easily pass data
between the two passes.
v1:
- Restrict to two passes (Jason Gunthorpe)
- Improve on documentation (Jason Gunthorpe)
- Improve on function naming (Alistair Popple)
v2:
- Include the invalidate_finish() callback in the
struct mmu_interval_notifier_ops.
- Update documentation (GitHub Copilot:claude-sonnet-4.6)
- Use lockless list for list management.
v3:
- Update kerneldoc for the struct mmu_interval_notifier_finish::list member
(Matthew Brost)
- Add a WARN_ON_ONCE() checking for NULL invalidate_finish() op if
if invalidate_start() is non-NULL. (Matthew Brost)
v4:
- Addressed documentation review comments by David Hildenbrand.
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: David Hildenbrand <david@kernel.org>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Vlastimil Babka <vbabka@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Simona Vetter <simona.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: <dri-devel@lists.freedesktop.org>
Cc: <linux-mm@kvack.org>
Cc: <linux-kernel@vger.kernel.org>
Assisted-by: GitHub Copilot:claude-sonnet-4.6 # Documentation only.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Acked-by: David Hildenbrand (Arm) <david@kernel.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patch.msgid.link/20260305093909.43623-2-thomas.hellstrom@linux.intel.com
|
|
Merge branch adding support for device-managed workqueue allocation,
which allows cleaning up a couple of power-supply drivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add documentation covering stmmac_clk, pclk, clk_ptp_ref and clk_tx_i
in the hope that this will help understand what each of these clocks
are for.
There is confusion around stmmac_clk and pclk which can't be easily
resolved today as the Imagination Technologies Pistachio board that
pclk was introduced for has no public documentation and is likely now
obsolete. So the origins of pclk are lost to the winds of time.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5Z-0000000CVsb-1XTm@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add documentation of each of the struct stmmac_dma_cfg members. dche
remains undocumented as I don't have documentation that covers this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5U-0000000CVsQ-162V@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We aren't going to see >= 256-bit address busses soon, so reduce
host_dma_width and associated other struct members that initialise
this from u32 to u8.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com> # qcom-ethqos
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5P-0000000CVsK-0iwX@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The maximum number of queues is a compile time constant of only eight.
This makes using a 32-bit quantity wastefulf. Instead, use u8 for
these and their associated variables.
When reading the DT properties, saturdate at U8_MAX. Provided the core
provides DMA capabilities to describe the number of queues, this will
be capped by stmmac_hw_init() with a warning.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5K-0000000CVsE-0J0Y@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reorder some of the stmmac structures to allow them to pack better,
thereby using less memory. On aarch64, sizeof(struct stmmac_priv)
was 880, and with this change becomes 816, saving 64 bytes, which
is an 8% saving.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5E-0000000CVs8-40w4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert members of struct plat_stmmacenet_data that are booleans to
type 'bool' and ensure their initialisers are true/false. Move the
has_xxx for the GMAC cores together, and move the COE members to the
end of the list of bool to avoid unused holes in the struct.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX59-0000000CVs2-3MHc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
plat_dat->dma_cfg is unconditionally required for the operation of the
driver, so it would make sense to allocate it along with the plat_dat.
On Arm64, sizeof(*plat_dat) has recently shrunk from 880 to 816 bytes
and sizeof(*plat_dat->dma_cfg) has shrunk from 32 to 20 bytes.
Given that dma_cfg is required, and it is now less than a cache line,
It doesn't make sense to allocate this separateny, so place it at the
end of struct plat_stmmacenet_data, and set plat_dat->dma_cfg to point
at that to avoid mass changes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX54-0000000CVrw-2jfu@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the correct function (or macro) names to avoid kernel-doc warnings:
Warning: include/linux/build_bug.h:38 function parameter 'cond' not
described in 'BUILD_BUG_ON_MSG'
Warning: include/linux/build_bug.h:38 function parameter 'msg' not
described in 'BUILD_BUG_ON_MSG'
Warning: include/linux/build_bug.h:76 function parameter 'expr' not
described in 'static_assert'
Link: https://lkml.kernel.org/r/20260302005144.3467019-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"15 hotfixes. 6 are cc:stable. 14 are for MM.
Singletons, with one doubleton - please see the changelogs for details"
* tag 'mm-hotfixes-stable-2026-03-09-16-36' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
MAINTAINERS, mailmap: update email address for Lorenzo Stoakes
mm/mmu_notifier: clean up mmu_notifier.h kernel-doc
uaccess: correct kernel-doc parameter format
mm/huge_memory: fix a folio_split() race condition with folio_try_get()
MAINTAINERS: add co-maintainer and reviewer for SLAB ALLOCATOR
MAINTAINERS: add RELAY entry
memcg: fix slab accounting in refill_obj_stock() trylock path
mm/hugetlb.c: use __pa() instead of virt_to_phys() in early bootmem alloc code
zram: rename writeback_compressed device attr
tools/testing: fix testing/vma and testing/radix-tree build
Revert "ptdesc: remove references to folios from __pagetable_ctor() and pagetable_dtor()"
mm/cma: move put_page_testzero() out of VM_WARN_ON in cma_release()
mm/damon/core: clear walk_control on inactive context in damos_walk()
mm: memfd_luo: always dirty all folios
mm: memfd_luo: always make all folios uptodate
|
|
Currently, audit_receive_msg() ignores unknown status bits in AUDIT_SET
requests, incorrectly returning success to newer user space tools
querying unsupported features. This breaks forward compatibility.
Fix this by defining AUDIT_STATUS_ALL and returning -EINVAL if any
unrecognized bits are set (s.mask & ~AUDIT_STATUS_ALL).
This ensures invalid requests are safely rejected, allowing user space
to reliably test for and gracefully handle feature detection on older
kernels.
Suggested-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Ricardo Robaina <rrobaina@redhat.com>
[PM: subject line tweak]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Document that the DT binding definitions in
<dt-bindings/interrupt-controller/irq.h> shadow the first six IRQ_TYPE_*
definitions in <linux/irq.h>. The values must be the same anyway, so this
is harmless (as long as the latter is included first when both are
included), but it is good to document this explicitly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/fbcc65dcee6c5437fab5ef18d21766bb4effb7cb.1772644406.git.geert+renesas@glider.be
|
|
|
|
Add a Resource-managed version of alloc_workqueue() to fix common
problem of drivers mixing devm() calls with destroy_workqueue. Such
naive and discouraged driver approach leads to difficult to debug bugs
when the driver:
1. Allocates workqueue in standard way and destroys it in driver
remove() callback,
2. Sets work struct with devm_work_autocancel(),
3. Registers interrupt handler with devm_request_threaded_irq().
Which leads to following unbind/removal path:
1. destroy_workqueue() via driver remove(),
Any interrupt coming now would still execute the interrupt handler,
which queues work on destroyed workqueue.
2. devm_irq_release(),
3. devm_work_drop() -> cancel_work_sync() on destroyed workqueue.
devm_alloc_workqueue() has two benefits:
1. Solves above problem of mix-and-match devres and non-devres code in
driver,
2. Simplify any sane drivers which were correctly using
alloc_workqueue() + devm_add_action_or_reset().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Userspace software fwupd probes some HID devices when the daemon starts
up to determine the current firmware version in order to be able to offer
updated firmware if the manufacturer has made it available.
In order to do this fwupd will detach the existing kernel driver if one
is present, send a HID command and then reattach the kernel driver.
This can be problematic if the user is using the HID device at the time
that fwupd probes the hardware and can cause a few frames of input to be
dropped. In some cases HID drivers already have a command to look up the
firmware version, and so if that is exported to userspace fwupd can
discover it and avoid needing to detach the kernel driver until it's time
to update the device.
Introduce a new member in the struct hid_device for the version and export
a new uevent variable HID_FIRMWARE_VERSION that will display the version
that HID drivers obtained.
Reviewed-by: Derek J. Clark <derekjohn.clark@gmail.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Cc: Richard Hughes <hughsient@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Adds DEVICE_ATTR_[RW|RO|WO]_NAMED macros for adding attributes that
reuse the same sysfs name in a driver under separate subdirectories.
When dealing with some devices it can be useful to be able to reuse
the same name for similar attributes under a different subdirectory.
For example, a single logical HID endpoint may provide a configuration
interface for multiple physical devices. In such a case it is useful to
provide symmetrical attribute names under different subdirectories on
the configuration device. The Lenovo Legion Go is one such device,
providing configuration to a detachable left controller, detachable
right controller, the wireless transmission dongle, and the MCU. It is
therefore beneficial to treat each of these as individual devices in
the driver, providing a subdirectory for each physical device in the
sysfs. As some attributes are reused by each physical device, it
provides a much cleaner interface if the same driver can reuse the same
attribute name in sysfs while uniquely distinguishing the store/show
functions in the driver, rather than repeat string portions.
Example new WO attrs:
ATTRS{left_handle/reset}=="(not readable)"
ATTRS{right_handle/reset}=="(not readable)"
ATTRS{tx_dongle/reset}=="(not readable)"
vs old WO attrs in a subdir:
ATTRS{left_handle/left_handle_reset}=="(not readable)"
ATTRS{right_handle/right_handle_reset}=="(not readable)"
ATTRS{tx_dongle/tx_dongle_reset}=="(not readable)"
or old WO attrs with no subdir:
ATTRS{left_handle_reset}=="(not readable)"
ATTRS{right_handle_reset}=="(not readable)"
ATTRS{tx_dongle_reset}=="(not readable)"
While the third option is usable, it doesn't logically break up the
physical devices and creates a device directory with over 80 attributes
once all attrs are defined.
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
In the current implementation, SVC client drivers such as socfpga-hwmon,
intel_fcs, stratix10-soc, stratix10-rsu each send an SMC command that
triggers a single thread in the stratix10-svc driver. Upon receiving a
callback, the initiating client driver sends a stratix10-svc-done signal,
terminating the thread without waiting for other pending SMC commands to
complete. This leads to a timeout issue in the firmware SVC mailbox service
when multiple client drivers send SMC commands concurrently.
To resolve this issue, a dedicated thread is now created per channel. The
stratix10-svc driver will support up to the number of channels defined by
SVC_NUM_CHANNEL. Thread synchronization is handled using a mutex to prevent
simultaneous issuance of SMC commands by multiple threads.
SVC_NUM_DATA_IN_FIFO is reduced from 32 to 8, since each channel now has
its own dedicated FIFO and the SDM processes commands one at a time.
8 entries per channel is sufficient while keeping the total aggregate
capacity the same (4 channels x 8 = 32 entries).
Additionally, a thread task is now validated before invoking kthread_stop
when the user aborts, ensuring safe termination.
Timeout values have also been adjusted to accommodate the increased load
from concurrent client driver activity.
Fixes: 7ca5ce896524 ("firmware: add Intel Stratix10 service layer driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ang Tien Sung <tien.sung.ang@altera.com>
Signed-off-by: Fong, Yan Kei <yankei.fong@altera.com>
Signed-off-by: Muhammad Amirul Asyraf Mohamad Jamian <muhammad.amirul.asyraf.mohamad.jamian@altera.com>
Link: https://lore.kernel.org/all/20260305093151.2678-1-muhammad.amirul.asyraf.mohamad.jamian@altera.com
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add the __counted_by() compiler attribute to the flexible array member
'key' to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Tunnel xmit functions (iptunnel_xmit, ip6tunnel_xmit) lack their own
recursion limit. When a bond device in broadcast mode has GRE tap
interfaces as slaves, and those GRE tunnels route back through the
bond, multicast/broadcast traffic triggers infinite recursion between
bond_xmit_broadcast() and ip_tunnel_xmit()/ip6_tnl_xmit(), causing
kernel stack overflow.
The existing XMIT_RECURSION_LIMIT (8) in the no-qdisc path is not
sufficient because tunnel recursion involves route lookups and full IP
output, consuming much more stack per level. Use a lower limit of 4
(IP_TUNNEL_RECURSION_LIMIT) to prevent overflow.
Add recursion detection using dev_xmit_recursion helpers directly in
iptunnel_xmit() and ip6tunnel_xmit() to cover all IPv4/IPv6 tunnel
paths including UDP encapsulated tunnels (VXLAN, Geneve, etc.).
Move dev_xmit_recursion helpers from net/core/dev.h to public header
include/linux/netdevice.h so they can be used by tunnel code.
BUG: KASAN: stack-out-of-bounds in blake2s.constprop.0+0xe7/0x160
Write of size 32 at addr ffff88810033fed0 by task kworker/0:1/11
Workqueue: mld mld_ifc_work
Call Trace:
<TASK>
__build_flow_key.constprop.0 (net/ipv4/route.c:515)
ip_rt_update_pmtu (net/ipv4/route.c:1073)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:84)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
mld_sendpack
mld_ifc_work
process_one_work
worker_thread
</TASK>
Fixes: 745e20f1b626 ("net: add a recursion limit in xmit path")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Link: https://patch.msgid.link/20260306160133.3852900-2-bestswngs@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Merge series from Sen Wang <sen@ti.com>:
Just two minor patches that aim to tidy up the code a little bit,
as well as fix the aux_div selection in davinci_mcasp_calc_clk_div()
for mid-range dividers (33 <= div <= 4096).
Sen Wang (2):
ASoC: ti: davinci-mcasp: extract mcasp_is_auxclk_enabled() helper
ASoC: ti: davinci-mcasp: improve aux_div selection for mid-range dividers
sound/soc/ti/davinci-mcasp.c | 45 +++++++++++++++++++++++++-----------
1 file changed, 31 insertions(+), 14 deletions(-)
--
2.43.0
|
|
Add support for generating / verifying protection information in iomap.
This is done by hooking into the bio submission and then using the
generic PI helpers. Compared to just using the block layer auto PI
this extends the protection envelope and also prepares for eventually
passing through PI from userspace at least for direct I/O.
To generate or verify PI, the file system needs to set the
IOMAP_F_INTEGRITY flag on the iomap for the request, and ensure the
ioends are used for all integrity I/O. Additionally the file system
must defer read I/O completions to user context so that the guard
tag validation isn't run from interrupt context.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260223132021.292832-16-hch@lst.de
Tested-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Optionally allocate the bio from the bioset provided in
iomap_read_folio_ops. If no bioset is provided, fs_bio_set is still
used, which is the standard bioset for file systems.
Based on a patch from Goldwyn Rodrigues <rgoldwyn@suse.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260223132021.292832-14-hch@lst.de
Tested-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
File systems such as btrfs have additional operations with bios such as
verifying data checksums. Allow file systems to hook into submission
of the bio to allow for this processing by replacing the direct
submit_bio call in iomap_read_alloc_bio with a call into ->submit_read
and exporting iomap_read_alloc_bio. Also add a new field to
struct iomap_read_folio_ctx to track the file logic offset of the current
read context.
Based on a patch from Goldwyn Rodrigues <rgoldwyn@suse.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260223132021.292832-12-hch@lst.de
Tested-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
This provides additional context for file systems.
Rename the fuse instance to match the method name while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260223132021.292832-10-hch@lst.de
Tested-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Bring in the shared branch with the block layer.
* 'for-7.1/block-integrity' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
block: pass a maxlen argument to bio_iov_iter_bounce
block: add fs_bio_integrity helpers
block: make max_integrity_io_size public
block: prepare generation / verification helpers for fs usage
block: add a bdev_has_integrity_csum helper
block: factor out a bio_integrity_setup_default helper
block: factor out a bio_integrity_action helper
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
chrono_type is currently in tcp_sock_read_txrx group, which
is supposed to hold read-mostly fields.
But chrono_type is mostly written in tx path, it should
be moved to tcp_sock_write_tx group, close to other
chrono fields (chrono_stat[], chrono_start).
Note this adds holes, but data locality is far more important.
Use a full u8 for the time being, compiler can generate
more efficient code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Link: https://patch.msgid.link/20260308122302.2895067-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into mbox
Bartosz Golaszewski says:
====================
Immutable branch between GPIO and net
Convert remaining users of of_gpio.h to using GPIO descriptors and
remove the header.
* tag 'ib-gpio-remove-of-gpio-h-for-v7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: remove of_get_named_gpio() and <linux/of_gpio.h>
nfc: nfcmrvl: convert to gpio descriptors
nfc: s3fwrn5: convert to gpio descriptors
====================
Link: https://patch.msgid.link/20260309093153.10446-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, ppp_input_error() indicates an error by allocating a 0-length
skb and calling ppp_do_recv(). It takes an error code argument, which is
stored in skb->cb, but not used by ppp_receive_frame().
Simplify the error handling by removing the unused parameter and the
unnecessary skb allocation. Instead, call ppp_receive_error() directly
from ppp_input_error() under the recv lock, and the length check in
ppp_receive_frame() can be removed.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A PCIe hotplug slot applies to the entire secondary bus. Thus, pciehp only
allocates a single hotplug_slot for the bridge to that bus. The existing
PCI slot, though, would only match to functions on device 0, meaning any
devices beyond that, e.g., ARI functions, are not matched to any slot even
though they share it. A slot reset will break all the missing devices
because the handling skips them.
For example, ARI devices with more than 8 functions fail because their
state is not properly handled, nor is the attached driver notified of the
reset. In the best case, the device will appear unresponsive to the driver,
resulting in unexpected errors. A worse possibility may panic the kernel if
in-flight transactions trigger hardware reported errors like this real
observation:
vfio-pci 0000:01:00.0: resetting
vfio-pci 0000:01:00.0: reset done
{1}[Hardware Error]: Error 1, type: fatal
{1}[Hardware Error]: section_type: PCIe error
{1}[Hardware Error]: port_type: 0, PCIe end point
{1}[Hardware Error]: version: 0.2
{1}[Hardware Error]: command: 0x0140, status: 0x0010
{1}[Hardware Error]: device_id: 0000:01:01.0
{1}[Hardware Error]: slot: 0
{1}[Hardware Error]: secondary_bus: 0x00
{1}[Hardware Error]: vendor_id: 0x1d9b, device_id: 0x0207
{1}[Hardware Error]: class_code: 020000
{1}[Hardware Error]: bridge: secondary_status: 0x0000, control: 0x0000
{1}[Hardware Error]: aer_cor_status: 0x00008000, aer_cor_mask: 0x00002000
{1}[Hardware Error]: aer_uncor_status: 0x00010000, aer_uncor_mask: 0x00100000
{1}[Hardware Error]: aer_uncor_severity: 0x006f6030
{1}[Hardware Error]: TLP Header: 0a412800 00192080 60000004 00000004
GHES: Fatal hardware error but panic disabled
Kernel panic - not syncing: GHES: Fatal hardware error
Allow a slot to be created to claim all devices on a bus, not just a
matching device. This is done by introducing a sentinel value, named
PCI_SLOT_ALL_DEVICES, which then has the PCI slot match to any device on
the bus. This fixes slot resets for pciehp.
Since 0xff already has special meaning, the chosen value for this new
feature is 0xfe. This will not clash with any actual slot number since they
are limited to 5 bits.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://patch.msgid.link/20260217160836.2709885-3-kbusch@meta.com
|
|
While the pblk argument to fscrypt_zeroout_range is declared as a
sector_t, it actually is interpreted as a logical block size unit, which
is highly unusual. Switch to passing the 512 byte units that sector_t is
defined for.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20260302141922.370070-14-hch@lst.de
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
Range lengths are usually expressed as bytes in the VFS, switch
fscrypt_zeroout_range to this convention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20260302141922.370070-13-hch@lst.de
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
Logical offsets into an inode are usually expressed as bytes in the VFS.
Switch fscrypt_zeroout_range to that convention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20260302141922.370070-12-hch@lst.de
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
Logical offsets into an inode are usually expressed as bytes in the VFS.
Switch fscrypt_set_bio_crypt_ctx to that convention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20260302141922.370070-9-hch@lst.de
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
Logical offsets into an inode are usually expressed as bytes in the VFS.
Switch fscrypt_mergeable_bio to that convention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20260302141922.370070-8-hch@lst.de
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
fscrypt_set_bio_crypt_ctx_bh is only used by submit_bh_wbc now. Move it
there and merge bh_get_inode_and_lblk_num into it.
Note that this does not add ifdefs for fscrypt as the compiler will
optimize away the dead code if it is not built in.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20260302141922.370070-6-hch@lst.de
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
ext4 already has the inode and folio and can't have a NULL
folio->mapping in this path. Open code fscrypt_mergeable_bio_bh in
io_submit_need_new_bio based on these simplifying assumptions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20260302141922.370070-5-hch@lst.de
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
Merge in integrity changes which are also landing in the VFS tree as
dependencies for fs related changes.
* for-7.1/block-integrity:
block: pass a maxlen argument to bio_iov_iter_bounce
block: add fs_bio_integrity helpers
block: make max_integrity_io_size public
block: prepare generation / verification helpers for fs usage
block: add a bdev_has_integrity_csum helper
block: factor out a bio_integrity_setup_default helper
block: factor out a bio_integrity_action helper
|
|
bdev_nonrot() is simply the negative return value of bdev_rot().
So replace all call sites of bdev_nonrot() with calls to bdev_rot()
and remove bdev_nonrot().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In order to maintain sequential write patterns per zone with zoned block
devices, zone write plugging issues only a single write BIO per zone at
any time. This works well but has the side effect that when large
sequential write streams are issued by the user and these streams cross
zone boundaries, the device ends up receiving a discontiguous set of
write commands for different zones. The same also happens when a user
writes simultaneously at high queue depth multiple zones: the device
does not see all sequential writes per zone and receives discontiguous
writes to different zones. While this does not affect the performance of
solid state zoned block devices, when using an SMR HDD, this pattern
change from sequential writes to discontiguous writes to different zones
significantly increases head seek which results in degraded write
throughput.
In order to reduce this seek overhead for rotational media devices,
introduce a per disk zone write plugs kernel thread to issue all write
BIOs to zones. This single zone write issuing context is enabled for
any zoned block device that has a request queue flagged with the new
QUEUE_ZONED_QD1_WRITES flag.
The flag QUEUE_ZONED_QD1_WRITES is visible as the sysfs queue attribute
zoned_qd1_writes for zoned devices. For regular block devices, this
attribute is not visible. For zoned block devices, a user can override
the default value set to force the global write maximum queue depth of
1 for a zoned block device, or clear this attribute to fallback to the
default behavior of zone write plugging which limits writes to QD=1 per
sequential zone.
Writing to a zoned block device flagged with QUEUE_ZONED_QD1_WRITES is
implemented using a list of zone write plugs that have a non-empty BIO
list. Listed zone write plugs are processed by the disk zone write plugs
worker kthread in FIFO order, and all BIOs of a zone write plug are all
processed before switching to the next listed zone write plug. A newly
submitted BIO for a non-FULL zone write plug that is not yet listed
causes the addition of the zone write plug at the end of the disk list
of zone write plugs.
Since the write BIOs queued in a zone write plug BIO list are
necessarilly sequential, for rotational media, using the single zone
write plugs kthread to issue all BIOs maintains a sequential write
pattern and thus reduces seek overhead and improves write throughput.
This processing essentially result in always writing to HDDs at QD=1,
which is not an issue for HDDs operating with write caching enabled.
Performance with write cache disabled is also not degraded thanks to
the efficient write handling of modern SMR HDDs.
A disk list of zone write plugs is defined using the new struct gendisk
zone_wplugs_list, and accesses to this list is protected using the
zone_wplugs_list_lock spinlock. The per disk kthread
(zone_wplugs_worker) code is implemented by the function
disk_zone_wplugs_worker(). A reference on listed zone write plugs is
always held until all BIOs of the zone write plug are processed by the
worker kthread. BIO issuing at QD=1 is driven using a completion
structure (zone_wplugs_worker_bio_done) and calls to blk_io_wait().
With this change, performance when sequentially writing the zones of a
30 TB SMR SATA HDD connected to an AHCI adapter changes as follows
(1MiB direct I/Os, results in MB/s unit):
+--------------------+
| Write BW (MB/s) |
+------------------+----------+---------+
| Sequential write | Baseline | Patched |
| Queue Depth | 6.19-rc8 | |
+------------------+----------+---------+
| 1 | 244 | 245 |
| 2 | 244 | 245 |
| 4 | 245 | 245 |
| 8 | 242 | 245 |
| 16 | 222 | 246 |
| 32 | 211 | 245 |
| 64 | 193 | 244 |
| 128 | 112 | 246 |
+------------------+----------+---------+
With the current code (baseline), as the sequential write stream crosses
a zone boundary, higher queue depth creates a gap between the
last IO to the previous zone and the first IOs to the following zones,
causing head seeks and degrading performance. Using the disk zone
write plugs worker thread, this pattern disappears and the maximum
throughput of the drive is maintained, leading to over 100%
improvements in throughput for high queue depth write.
Using 16 fio jobs all writing to randomly chosen zones at QD=32 with 1
MiB direct IOs, write throughput also increases significantly.
+--------------------+
| Write BW (MB/s) |
+------------------+----------+---------+
| Random write | Baseline | Patched |
| Number of zones | 6.19-rc7 | |
+------------------+----------+---------+
| 1 | 191 | 192 |
| 2 | 101 | 128 |
| 4 | 115 | 123 |
| 8 | 90 | 120 |
| 16 | 64 | 115 |
| 32 | 58 | 105 |
| 64 | 56 | 101 |
| 128 | 55 | 99 |
+------------------+----------+---------+
Tests using XFS shows that buffered write speed with 8 jobs writing
files increases by 12% to 35% depending on the workload.
+--------------------+
| Write BW (MB/s) |
+------------------+----------+---------+
| Workload | Baseline | Patched |
| | 6.19-rc7 | |
+------------------+----------+---------+
| 256MiB file size | 212 | 238 |
+------------------+----------+---------+
| 4MiB .. 128 MiB | 213 | 243 |
| random file size | | |
+------------------+----------+---------+
| 2MiB .. 8 MiB | 179 | 242 |
| random file size | | |
+------------------+----------+---------+
Performance gains are even more significant when using an HBA that
limits the maximum size of commands to a small value, e.g. HBAs
controlled with the mpi3mr driver limit commands to a maximum of 1 MiB.
In such case, the write throughput gains are over 40%.
+--------------------+
| Write BW (MB/s) |
+------------------+----------+---------+
| Workload | Baseline | Patched |
| | 6.19-rc7 | |
+------------------+----------+---------+
| 256MiB file size | 175 | 245 |
+------------------+----------+---------+
| 4MiB .. 128 MiB | 174 | 244 |
| random file size | | |
+------------------+----------+---------+
| 2MiB .. 8 MiB | 171 | 243 |
| random file size | | |
+------------------+----------+---------+
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Rename struct gendisk zone_wplugs_lock field to zone_wplugs_hash_lock to
clearly indicates that this is the spinlock used for manipulating the
hash table of zone write plugs.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
