| Age | Commit message (Collapse) | Author |
|---|
|
The LT9611 has two DSI input ports. The driver currently assumes Port A
is always used for single-port configurations. However, some boards
connect DSI to Port B only.
Update the driver to detect which ports are populated from devicetree
and configure the hardware accordingly:
- If only port@1 (Port B) is populated, configure port swap (0x8303
bit 6) and byte_clk source (0x8250 bit 3:2) for Port B operation
- If both ports are populated, use dual-port mode (Port A + B)
- If only port@0 (Port A) is populated, use single Port A (existing
behavior)
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Hongyang Zhao <hongyang.zhao@thundersoft.com>
Reviewed-by: Roger Shimizu <rosh@debian.org>
Tested-by: Roger Shimizu <rosh@debian.org>
Link: https://patch.msgid.link/20260207-rubikpi-next-20260116-v3-2-23b9aa189a3a@thundersoft.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Fallback to polling to detect hotplug events on systems without
interrupts.
On systems where the interrupt line of the bridge is not connected,
the bridge cannot notify hotplug events. Only add the
DRM_BRIDGE_OP_HPD flag if an interrupt has been registered
otherwise remain in polling mode.
Fixes: 55e8ff842051 ("drm/bridge: ti-sn65dsi86: Add HPD for DisplayPort connector type")
Cc: stable@vger.kernel.org # 6.16: 9133bc3f0564: drm/bridge: ti-sn65dsi86: Add
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[dianders: Adjusted Fixes/stable line based on discussion]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20260206123758.374555-1-fra.schnyder@gmail.com
|
|
The GuC pagefault acknowledgment code is designed to extract the fields
needed for the acknowledgment from the producer-stored message so that
the consumer fields can be overloaded to return additional information.
The ASID is stored in the producer message; extract it from there to
future‑proof this logic.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://patch.msgid.link/20260212204227.2764054-3-matthew.brost@intel.com
|
|
Pack the fault type and level fields into a single u8 to save space in
struct xe_pagefault. This also makes future extensions easier.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://patch.msgid.link/20260212204227.2764054-2-matthew.brost@intel.com
|
|
Applied Wa_14024997852 to Graphics version 20.01 to 20.04
Whitelist registers needed for userspace to control autostrip on xe2.
v2:
- set Bit 31 of FF_MODE, for TE autostrip disable (Nitin)
v3:
- Need to whitelist these for Xe2 IPs (MATT R)
v4:
- Combine these into a single range for simplicity:(2001, 3005)
(MATT R)
Cc: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Nitin Gote <nitin.r.gote@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Arvind Yadav <arvind.yadav@intel.com>
Link: https://patch.msgid.link/20260212065920.1815979-1-arvind.yadav@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
As per uapi documentation[1], the prerequisite for wedged device is to
redirected page faults to a dummy page. Follow it.
[1] Documentation/gpu/drm-uapi.rst
v2: Add uapi reference and fixes tag (Matthew Brost)
Fixes: 7bc00751f877 ("drm/xe: Use device wedged event")
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260212055622.2054991-1-raag.jadav@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
VMs created without an associated xe_file originate from kernel
contexts and should use kernel exec queues. Ensure such VMs
create bind exec queues with EXEC_QUEUE_FLAG_KERNEL set.
Let's ensure bind exec queues created for kernel VMs are always
marked with EXEC_QUEUE_FLAG_KERNEL.
Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20260211171441.3246686-1-piotr.piorkowski@intel.com
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-6.20-2026-02-06:
amdgpu:
- DML 2.1 fixes
- Panel replay fixes
- Display writeback fixes
- MES 11 old firmware compat fix
- DC CRC improvements
- DPIA fixes
- XGMI fixes
- ASPM fix
- SMU feature bit handling fixes
- DC LUT fixes
- RAS fixes
- Misc memory leak in error path fixes
- SDMA queue reset fixes
- PG handling fixes
- 5 level GPUVM page table fix
- SR-IOV fix
- Queue reset fix
amdkfd:
- Fix possible double deletion of validate list
- Event setup fix
- Device disconnect regression fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patch.msgid.link/20260206192706.59396-1-alexander.deucher@amd.com
|
|
Wa_16018737384 is one of the rare cases where the hardware teams mark a
workaround as "driver change required" rather than "permanent/temporary
workaround" in the internal workaround database, signifying that the
implementation details of the workaround should just be considered
standard programming instructions on all platforms going forward. Cases
like this are the only time that using XE_RTP_END_VERSION_UNDEFINED as an
upper bound for a workaround's IP range is warranted and correct.
However in this specific case, the register bit in question (0xE4F0[1])
simply no longer exists in hardware from Xe3 onward. Trying to write to
that bit on Xe3 or Xe3p platforms is harmless and just doesn't have any
effect, but it's possible that the register bit could get repurposed to
control something else down the road on future platforms. To avoid any
surprises in the future we should replace the unbounded upper bound in
our RTP table with a value that accurately reflects that Wa_16018737384
can only apply to Xe2 platforms.
Bspec: 56849
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Link: https://patch.msgid.link/20260211234735.620087-2-matthew.d.roper@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
In order to be able to use only vma_flags_t in vm_area_desc we must adjust
shmem file setup functions to operate in terms of vma_flags_t rather than
vm_flags_t.
This patch makes this change and updates all callers to use the new
functions.
No functional changes intended.
[akpm@linux-foundation.org: comment fixes, per Baolin]
Link: https://lkml.kernel.org/r/736febd280eb484d79cef5cf55b8a6f79ad832d2.1769097829.git.lorenzo.stoakes@oracle.com
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Barry Song <baohua@kernel.org>
Cc: David Hildenbrand <david@kernel.org>
Cc: Dev Jain <dev.jain@arm.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Zi Yan <ziy@nvidia.com>
Cc: "Darrick J. Wong" <djwong@kernel.org>
Cc: Damien Le Moal <dlemoal@kernel.org>
Cc: Yury Norov <ynorov@nvidia.com>
Cc: Chris Mason <clm@fb.com>
Cc: Pedro Falcato <pfalcato@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The VM was not locked in the past since we initially only cleared the
linked list element and not added it to any VM state.
But this has changed quite some time ago, we just never realized this
problem because the VM state lock was masking it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
eng_id can be negative and that stream_enc_regs[]
can be indexed out of bounds.
eng_id is used directly as an index into stream_enc_regs[], which has
only 5 entries. When eng_id is 5 (ENGINE_ID_DIGF) or negative, this can
access memory past the end of the array.
Add a bounds check using ARRAY_SIZE() before using eng_id as an index.
The unsigned cast also rejects negative values.
This avoids out-of-bounds access.
Fixes the below smatch error:
dcn*_resource.c: stream_encoder_create() may index
stream_enc_regs[eng_id] out of bounds (size 5).
drivers/gpu/drm/amd/amdgpu/../display/dc/resource/dcn351/dcn351_resource.c
1246 static struct stream_encoder *dcn35_stream_encoder_create(
1247 enum engine_id eng_id,
1248 struct dc_context *ctx)
1249 {
...
1255
1256 /* Mapping of VPG, AFMT, DME register blocks to DIO block instance */
1257 if (eng_id <= ENGINE_ID_DIGF) {
ENGINE_ID_DIGF is 5. should <= be <?
Unrelated but, ugh, why is Smatch saying that "eng_id" can be negative?
end_id is type signed long, but there are checks in the caller which prevent it from being negative.
1258 vpg_inst = eng_id;
1259 afmt_inst = eng_id;
1260 } else
1261 return NULL;
1262
...
1281
1282 dcn35_dio_stream_encoder_construct(enc1, ctx, ctx->dc_bios,
1283 eng_id, vpg, afmt,
--> 1284 &stream_enc_regs[eng_id],
^^^^^^^^^^^^^^^^^^^^^^^ This stream_enc_regs[] array has 5 elements so we are one element beyond the end of the array.
...
1287 return &enc1->base;
1288 }
v2: use explicit bounds check as suggested by Roman/Dan; avoid unsigned int cast
v3: The compiler already knows how to compare the two values, so the
cast (int) is not needed. (Roman)
Fixes: 2728e9c7c842 ("drm/amd/display: add DC changes for DCN351")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Mario Limonciello <superm1@kernel.org>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Cc: Roman Li <roman.li@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add a check in mqd_on_vram. If the device prefers GTT, it returns false
Fixes: d4a814f400d4 ("drm/amdkfd: Move gfx9.4.3 and gfx 9.5 MQD to HBM")
Signed-off-by: Siwei He <siwei.he@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for psp v13_0_15 ip block
Signed-off-by: Mangesh Gadre <Mangesh.Gadre@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set the family for GC 11.5.4
Fixes: 47ae1f938d12 ("drm/amdgpu: add support for GC IP version 11.5.4")
Cc: Tim Huang <tim.huang@amd.com>
Cc: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Cc: Roman Li <Roman.Li@amd.com>
Reviewed-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch limits the clock speeds of the AMD Radeon R5 M420 GPU from
850/1000MHz (core/memory) to 800/950 MHz, making it work stably. This
patch is for amdgpu.
Signed-off-by: decce6 <decce6@proton.me>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch limits the clock speeds of the AMD Radeon R5 M420 GPU from
850/1000MHz (core/memory) to 800/950 MHz, making it work stably. This
patch is for radeon.
Signed-off-by: decce6 <decce6@proton.me>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move SMU v15_0_0 specific functions to IP file
- smu_v15_0_0_set_default_dpm_tables and
- smu_v15_0_0_update_table
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Invalidating a dmabuf will impact other users of the shared BO.
In the scenario where process A moves the BO, it needs to inform
process B about the move and process B will need to update its
page table.
The commit fixes a synchronisation bug caused by the use of the
ticket: it made amdgpu_vm_handle_moved behave as if updating
the page table immediately was correct but in this case it's not.
An example is the following scenario, with 2 GPUs and glxgears
running on GPU0 and Xorg running on GPU1, on a system where P2P
PCI isn't supported:
glxgears:
export linear buffer from GPU0 and import using GPU1
submit frame rendering to GPU0
submit tiled->linear blit
Xorg:
copy of linear buffer
The sequence of jobs would be:
drm_sched_job_run # GPU0, frame rendering
drm_sched_job_queue # GPU0, blit
drm_sched_job_done # GPU0, frame rendering
drm_sched_job_run # GPU0, blit
move linear buffer for GPU1 access #
amdgpu_dma_buf_move_notify -> update pt # GPU0
It this point the blit job on GPU0 is still running and would
likely produce a page fault.
Cc: stable@vger.kernel.org
Fixes: a448cb003edc ("drm/amdgpu: implement amdgpu_gem_prime_move_notify v2")
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
These definitions are used by user APIs.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
end the function flow when ras table checksum is error
Signed-off-by: Gangliang Xie <ganglxie@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Tune the sleep interval in the PSP fence wait loop from 10-100us to
60-100us.This adjustment results in an overall wait window of 1.2s
(60us * 20000 iterations) to 2 seconds (100us * 20000 iterations),
which guarantees that we can retrieve the correct fence value
Signed-off-by: Ce Sun <cesun102@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SMU 15_0_0 exports only soft limits for CLKs
Use correct messages
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enable GFXOff for GC 11.5.4
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set the default reset method to mode2 for SMU 15.0.0.
Signed-off-by: Kanala Ramalingeswara Reddy <Kanala.RamalingeswaraReddy@amd.com>
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Not supported on SMU 15_0_0
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
drop set_driver_table_location
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use multi args for get_enabled_mask to fix is_dpm_running
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use smu_v15_0_0_update_table instead of common api
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Acked-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use multi param based get op for metrics_table
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add update_table for SMU 15_0_0
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some SMU messages have changed to multi reg read/write
Initialize during smu_early_init
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
TOC and TA both are required
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Send unload command to smu during modprobe -r amdgpu for smu 13/14.
1. This can fix the high voltage/temperatue issue after driver is unloaded.
2. Reloading driver could fail but with the debug port based mode1 reset
during driver is reloaded, it is good and safe.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
use debug port for mode1 reset request so fw can handle mode1 reset
even when it is stuck.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently DCE doesn't support the overlay cursor, so the
dm_crtc_get_cursor_mode() function returns DM_CURSOR_NATIVE_MODE
unconditionally. The outcome is that it doesn't check for the
conditions that would necessitate the overlay cursor, meaning
that it doesn't reject cases where the native cursor mode isn't
supported on DCE.
Remove the early return from dm_crtc_get_cursor_mode() for
DCE and instead let it perform the necessary checks and
return DM_CURSOR_OVERLAY_MODE. Add a later check that rejects
when DM_CURSOR_OVERLAY_MODE would be used with DCE.
Fixes: 1b04dcca4fb1 ("drm/amd/display: Introduce overlay cursor mode")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4600
Suggested-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The driver uses strncmp() to compare sysfs attribute strings,
which does not handle trailing newlines and lacks NULL safety.
sysfs_streq() is the recommended function for sysfs string equality
checks in the kernel, providing safer and more correct behavior.
replace strncmp() with sysfs_streq() in drivers/gpu/drm/amd/pm/amdgpu_pm.c
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The address watch clear code receives watch_id as an unsigned value
(u32), but some helper functions were using a signed int and checked
bits by shifting with watch_id.
If a very large watch_id is passed from userspace, it can be converted
to a negative value. This can cause invalid shifts and may access
memory outside the watch_points array.
drm/amdkfd: Fix watch_id bounds checking in debug address watch v2
Fix this by checking that watch_id is within MAX_WATCH_ADDRESSES before
using it. Also use BIT(watch_id) to test and clear bits safely.
This keeps the behavior unchanged for valid watch IDs and avoids
undefined behavior for invalid ones.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_debug.c:448
kfd_dbg_trap_clear_dev_address_watch() error: buffer overflow
'pdd->watch_points' 4 <= u32max user_rl='0-3,2147483648-u32max' uncapped
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_debug.c
433 int kfd_dbg_trap_clear_dev_address_watch(struct kfd_process_device *pdd,
434 uint32_t watch_id)
435 {
436 int r;
437
438 if (!kfd_dbg_owns_dev_watch_id(pdd, watch_id))
kfd_dbg_owns_dev_watch_id() doesn't check for negative values so if
watch_id is larger than INT_MAX it leads to a buffer overflow.
(Negative shifts are undefined).
439 return -EINVAL;
440
441 if (!pdd->dev->kfd->shared_resources.enable_mes) {
442 r = debug_lock_and_unmap(pdd->dev->dqm);
443 if (r)
444 return r;
445 }
446
447 amdgpu_gfx_off_ctrl(pdd->dev->adev, false);
--> 448 pdd->watch_points[watch_id] = pdd->dev->kfd2kgd->clear_address_watch(
449 pdd->dev->adev,
450 watch_id);
v2: (as per, Jonathan Kim)
- Add early watch_id >= MAX_WATCH_ADDRESSES validation in the set path to
match the clear path.
- Drop the redundant bounds check in kfd_dbg_owns_dev_watch_id().
Fixes: e0f85f4690d0 ("drm/amdkfd: add debug set and clear address watch points operation")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: Jonathan Kim <jonathan.kim@amd.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amdgpu_ib_schedule() returns early after calling amdgpu_ring_undo().
This skips the common free_fence cleanup path. Other error paths were
already changed to use goto free_fence, but this one was missed.
Change the early return to goto free_fence so all error paths clean up
the same way.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_ib.c:232 amdgpu_ib_schedule()
warn: missing unwind goto?
drivers/gpu/drm/amd/amdgpu/amdgpu_ib.c
124 int amdgpu_ib_schedule(struct amdgpu_ring *ring, unsigned int num_ibs,
125 struct amdgpu_ib *ibs, struct amdgpu_job *job,
126 struct dma_fence **f)
127 {
...
224
225 if (ring->funcs->insert_start)
226 ring->funcs->insert_start(ring);
227
228 if (job) {
229 r = amdgpu_vm_flush(ring, job, need_pipe_sync);
230 if (r) {
231 amdgpu_ring_undo(ring);
--> 232 return r;
The patch changed the other error paths to goto free_fence but
this one was accidentally skipped.
233 }
234 }
235
236 amdgpu_ring_ib_begin(ring);
...
338
339 free_fence:
340 if (!job)
341 kfree(af);
342 return r;
343 }
Fixes: f903b85ed0f1 ("drm/amdgpu: fix possible fence leaks from job structure")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amdgpu_dm_hpd_init() may see connectors without a valid dc_link.
The code already checks dc_link for the polling decision, but later
unconditionally dereferences it when setting up HPD interrupts.
Assign dc_link early and skip connectors where it is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_irq.c:940 amdgpu_dm_hpd_init()
error: we previously assumed 'dc_link' could be null (see line 931)
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_irq.c
923 /*
924 * Analog connectors may be hot-plugged unlike other connector
925 * types that don't support HPD. Only poll analog connectors.
926 */
927 use_polling |=
928 amdgpu_dm_connector->dc_link &&
^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The patch adds this NULL check but hopefully it can be removed
929 dc_connector_supports_analog(amdgpu_dm_connector->dc_link->link_id.id);
930
931 dc_link = amdgpu_dm_connector->dc_link;
dc_link assigned here.
932
933 /*
934 * Get a base driver irq reference for hpd ints for the lifetime
935 * of dm. Note that only hpd interrupt types are registered with
936 * base driver; hpd_rx types aren't. IOW, amdgpu_irq_get/put on
937 * hpd_rx isn't available. DM currently controls hpd_rx
938 * explicitly with dc_interrupt_set()
939 */
--> 940 if (dc_link->irq_source_hpd != DC_IRQ_SOURCE_INVALID) {
^^^^^^^^^^^^^^^^^^^^^^^ If it's NULL then we are trouble because we dereference it here.
941 irq_type = dc_link->irq_source_hpd - DC_IRQ_SOURCE_HPD1;
942 /*
943 * TODO: There's a mismatch between mode_info.num_hpd
944 * and what bios reports as the # of connectors with hpd
Fixes: 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)")
Cc: Timur Kristóf <timur.kristof@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Mario Limonciello <superm1@kernel.org>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Cc: Roman Li <roman.li@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This version brings along following update:
-Fix system resume lag issue
-Correct hubp GfxVersion verification
-Add parse all extension blocks for VSDB
-Increase DCN35 SR enter/exit latency
-Refactor virtual directory reorganize encoder and hwss files
-Set enable_legacy_fast_update to false for DCN36
-Have dm_atomic_state context aligned with dc_state current
-Avoid updating surface with the same surface under MPO
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add some struct member and enum for panel replay
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
soc->max_outstanding_reqs is a dml_uint_t, not a dml_float_t.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For RGB BT2020 full and limited color spaces, overlay adjustments were
applied twice (once by MM and once by DAL). This results in incorrect
colours and a noticeable difference between mpo and non-mpo cases.
[How]
Add RGB BT2020 full and limited color spaces to list that bypasses post
csc adjustment.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Clay King <clayking@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
component."
[Why & How]
This reverts commit 949adb4789fe3c24eea01d9c2efe94ab92694a0d, which
causes regressions related to HDCP when resuming from S3.
Reviewed-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Nicholas Carbones <ncarbone@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DcGfxBase case was not accounted for in hubp program tiling functions,
causing tiling corruption on PNP.
[How]
Add handling for DcGfxBase so that tiling gets properly cleared.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Nicholas Carbones <ncarbone@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit ba448f9ed62cf5a89603a738e6de91fc6c42ab35.
It cause some regression.
Reviewed-by: Sreeja Golui <sreeja.golui@amd.com>
Signed-off-by: Muaaz Nisar <muanisar@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
VSDB parsing loop only searched within the first extension block.
If the VSDB was located in a subsequent extension block,
it would not be found.
[How]
Calculate the total length of all extension blocks (EDID_LENGTH *
edid->extensions) and use that as the loop boundary, allowing the
parser to search through all available extension blocks.
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- "ocfs2: give ocfs2 the ability to reclaim suballocator free bg" saves
disk space by teaching ocfs2 to reclaim suballocator block group
space (Heming Zhao)
- "Add ARRAY_END(), and use it to fix off-by-one bugs" adds the
ARRAY_END() macro and uses it in various places (Alejandro Colomar)
- "vmcoreinfo: support VMCOREINFO_BYTES larger than PAGE_SIZE" makes
the vmcore code future-safe, if VMCOREINFO_BYTES ever exceeds the
page size (Pnina Feder)
- "kallsyms: Prevent invalid access when showing module buildid" cleans
up kallsyms code related to module buildid and fixes an invalid
access crash when printing backtraces (Petr Mladek)
- "Address page fault in ima_restore_measurement_list()" fixes a
kexec-related crash that can occur when booting the second-stage
kernel on x86 (Harshit Mogalapalli)
- "kho: ABI headers and Documentation updates" updates the kexec
handover ABI documentation (Mike Rapoport)
- "Align atomic storage" adds the __aligned attribute to atomic_t and
atomic64_t definitions to get natural alignment of both types on
csky, m68k, microblaze, nios2, openrisc and sh (Finn Thain)
- "kho: clean up page initialization logic" simplifies the page
initialization logic in kho_restore_page() (Pratyush Yadav)
- "Unload linux/kernel.h" moves several things out of kernel.h and into
more appropriate places (Yury Norov)
- "don't abuse task_struct.group_leader" removes the usage of
->group_leader when it is "obviously unnecessary" (Oleg Nesterov)
- "list private v2 & luo flb" adds some infrastructure improvements to
the live update orchestrator (Pasha Tatashin)
* tag 'mm-nonmm-stable-2026-02-12-10-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (107 commits)
watchdog/hardlockup: simplify perf event probe and remove per-cpu dependency
procfs: fix missing RCU protection when reading real_parent in do_task_stat()
watchdog/softlockup: fix sample ring index wrap in need_counting_irqs()
kcsan, compiler_types: avoid duplicate type issues in BPF Type Format
kho: fix doc for kho_restore_pages()
tests/liveupdate: add in-kernel liveupdate test
liveupdate: luo_flb: introduce File-Lifecycle-Bound global state
liveupdate: luo_file: Use private list
list: add kunit test for private list primitives
list: add primitives for private list manipulations
delayacct: fix uapi timespec64 definition
panic: add panic_force_cpu= parameter to redirect panic to a specific CPU
netclassid: use thread_group_leader(p) in update_classid_task()
RDMA/umem: don't abuse current->group_leader
drm/pan*: don't abuse current->group_leader
drm/amd: kill the outdated "Only the pthreads threading model is supported" checks
drm/amdgpu: don't abuse current->group_leader
android/binder: use same_thread_group(proc->tsk, current) in binder_mmap()
android/binder: don't abuse current->group_leader
kho: skip memoryless NUMA nodes when reserving scratch areas
...
|
|
[Why]
Avoid unnecessary GPIO configuration attempts on dcn that doesn't
support it.
[How]
Conditionally use GPIO HPD detection or rely on hw encoder path.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
