| Age | Commit message (Collapse) | Author |
|---|
|
The witable override should be set when FDO_MODE bit is enabled.
Fix the comparison to distingush this case from legacy systems
where bit should be disabled to have override.
Cc: stable@vger.kernel.org
Fixes: 9dde74fd9e65 ("drm/xe/nvm: enable cri platform")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patch.msgid.link/20260714-cri_nvm_fdo_flip-v2-1-14580e71b58e@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 2007be18d2318a59748da5da1b8968042213d5f1)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
An imported dma-buf BO is created as a ttm_bo_type_sg BO whose
reservation object is the exporter's dma_buf->resv. The importer,
however, only takes a dma-buf reference after a successful
dma_buf_dynamic_attach(). Until then nothing keeps the exporter alive,
so if the exporter is freed while the BO still references its resv, a
later access to that resv is a use-after-free:
Oops: general protection fault, probably for non-canonical address
0x6b6b6b6b6b6b6b9c
Workqueue: ttm ttm_bo_delayed_delete [ttm]
RIP: 0010:mutex_can_spin_on_owner+0x3f/0xc0
This can be reached on two paths:
- dma_buf_dynamic_attach() fails, or
- ttm_bo_init_reserved() fails during BO creation.
In both cases the BO already has bo->base.resv pointing at the exporter
resv, and sg BOs are always torn down via ttm_bo_delayed_delete(), which
locks bo->base.resv asynchronously - potentially after the exporter has
been freed.
Take the dma-buf reference in xe_bo_init_locked(), before
ttm_bo_init_reserved(), so it also covers a creation failure there, and
release it in xe_ttm_bo_destroy(). The reference is held for the whole
BO lifetime, keeping the shared resv alive on every path.
v2:
- Reworked the fix to avoid creating the imported sg BO before
dma_buf_dynamic_attach() succeeds.
- Attach with importer_priv == NULL and make invalidate_mappings ignore
incomplete imports.
v3:
- Dropped the xe-side reordering approach since importer_priv must be
valid when dma_buf_dynamic_attach() publishes the attachment.
- Per Christian's suggestion on the v1 thread, keyed the check on
import_attach rather than removing the sg guard entirely.
- Fixes both xe and amdgpu in a single TTM patch.
v4:
- Moved import_attach check to after dma_resv_copy_fences() so fences
are copied before returning for successful imports (Thomas).
- Removed exporter-alive claim from commit message (Thomas).
v5:
- Add drm/xe patch to keep imported sg BOs off the LRU before attach
succeeds; the TTM fix alone is not sufficient for xe if the BO is
already LRU-visible. (Thomas)
v4 patch:
https://patchwork.freedesktop.org/patch/736663/?series=169129&rev=2
- Patch 1 (drm/ttm) carries Christian's Reviewed-by from v4.
v6:
- Reworked the fix based on Thomas' suggestion. Instead of the TTM resv
individualization (v1-v5) plus the xe off-LRU/placement handling (v5),
just hold a dma-buf reference for the imported BO lifetime so the
shared resv can never be freed while the BO still references it.
Single xe patch, no TTM change. (Thomas)
- Take the reference in xe_bo_init_locked() before ttm_bo_init_reserved()
so a TTM creation failure is covered too (Thomas).
- Dropped the v5 series (drm/ttm + drm/xe off-LRU); the off-LRU approach
also regressed in CI BAT via ttm_bo_pipeline_gutting() creating a ghost
BO that outlived the exporter.
Link to v5: https://patchwork.freedesktop.org/series/169984/
v7:
- Move changelog above --- so it stays in the commit message.
- Reorder changelog entries oldest-to-newest. (Thomas)
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/work_items/8023
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: stable@vger.kernel.org
Cc: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Cc: Christian Konig <christian.koenig@amd.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Suggested-by: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Assisted-by: GitHub_Copilot:claude-sonnet-4.6
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Nitin Gote <nitin.r.gote@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patch.msgid.link/20260710191027.260160-2-nitin.r.gote@intel.com
(cherry picked from commit 3516f3fae6be35642f8f06f8a218da6425c0306a)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
When prefetch region is DRM_XE_CONSULT_MEM_ADVISE_PREF_LOC for a BO VMA,
the code used it as an index into region_to_mem_type[], causing an
out-of-bounds access since the value is -1.
Resolve the preferred location for BO VMAs directly: local VRAM on dGFX
(using the BO's tile placement) or system memory on iGPU.
Discovered using AI-assisted static analysis confirmed by Intel Product
Security.
v2:
-Fix null dereference
Reported-by: Martin Hodo <martin.hodo@intel.com>
Fixes: c1bb69a2e8e2 ("drm/xe/svm: Consult madvise preferred location in prefetch")
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20260624174943.2808767-2-himal.prasad.ghimiray@intel.com
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
(cherry picked from commit d9a4906ac03be9f6ed3f3b45c56c866b867fd75b)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Pull kvm fixes from Paolo Bonzini:
"arm64:
- Fix an accounting buglet when reclaiming pages from a protected
guest
- Fix a bunch of architectural compliance issues when injecting a
synthesised exception, most of which were missing the PSTATE.IL bit
indicating a 32bit-wide instruction
- Another set of fixes addressing issues with translation of
VNCR_EL2, including corner cases where the guest point that
register at a RO page...
- Don't warn when trapping accesses to ZCR_EL2 from an L2 guest, as
that's not unexpected at all
- Address a bunch of races with LPI migration vs LPIs being disabled
- Fix a total howler of a bug combining FEAT_MOPS and NV, resulting
in exception returning in the wrong place...
- Move locking for kvm_io_bus_get_dev() into the caller, ensuring
race-free checks that the returned object is of the correct type
- Fix initialisation of the page-table walk level when relaxing
permissions
- Correctly update the XN attribute when relaxing permissions
- Fix the sign extension of loads from emulated MMIO regions
- Assorted collection of fixes for pKVM's FFA proxy, together with a
couple of FFA driver adjustments
- Coerce Fuad Tabba into a reviewer role, and may his Inbox catch
fire!
s390:
- more gmap KVM memory management fixes
- PCI passthru fixes
x86:
- Fix a bug where KVM will trigger a UAF if updating IOMMU IRTEs
fails when registering an IRQ-bypass producer
- Ignore pending PV EOI instead of BUG()ing the host if the feature
was disabled by the guest
- Fix nVMX bugs where KVM would run L1 with an L1-controlled CR3
after a failed "late" consistency check when KVM is NOT using EPT
- Disallow intra-host migration/mirroring of SNP VMs as KVM doesn't
yet support moving/mirroring SNP state
- Fix a TOCTOU bug in KVM's handling of the "trusted" CPUID for TDX
guests
- Fix a NULL pointer deref in trace_kvm_inj_exception() where a
change to the core infrastructure missed KVM's unique (ab)use of
__print_symbolic()
- Put vmcs12 pages if nested VM-Enter fails due to invalid guest
state
- Fix TLB conflicts between two VMs if one of them VM is run on a CPU
before and after it is hotplugged"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (48 commits)
KVM: SVM: Bump asid_generation on CPU online to avoid ASID collision after hotplug
KVM: nVMX: Put vmcs12 pages if nested VM-Enter fails due to invalid guest state
KVM: x86: Fix null pointer deref due to dummy array in trace_kvm_inj_exception()
KVM: TDX: Reject concurrent change to CPUID entry count
KVM: selftests: Verify SNP VMs are rejected from migration and mirroring
KVM: SEV: Do not allow intra-host migration/mirroring of SNP VMs
KVM: s390: pci: Fix handling of AIF enable without AISB
KVM: s390: Improve kvm_s390_vm_stop_migration()
KVM: s390: Fix dat_crste_walk_range() early return
KVM: s390: vsie: Avoid potential deadlock with real spaces
KVM: s390: pci: Fix GISC refcount leak on AIF enable failure
KVM: nVMX: Don't use vmcs01.GUEST_CR3 to snapshot L1's CR3 when EPT is disabled
KVM: nVMX: Move vTPR vs. TPR Threshold consistency check into "normal" checks
KVM: x86: Ignore pending PV EOI if the vCPU has since disabled PV EOIs
KVM: x86: Nullify irqfd->producer if updating IRTE for bypass fails
KVM: arm64: Fix propagation of TLBI level in kvm_pgtable_stage2_relax_perms()
firmware: arm_ffa: Fix Endpoint Memory Access Descriptor offset calculation
firmware: arm_ffa: Fix out-of-bound writes in ffa_setup_and_transmit()
KVM: arm64: Zero out the stack initialized data in the FFA handler
KVM: arm64: Ensure FFA ranges are page aligned
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v7.2
- Fix lock-ups on the Ironhide development board.
* tag 'renesas-fixes-for-v7.2-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: ironhide: Describe inline ECC carveouts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
bio_iov_iter_align_down expects the "normal" biovec layout from vector 0,
while bio_iov_iter_bounce_read abuses vector 0 for a bounce buffer
allocation. Pass an explicit bvec to bio_iov_iter_align_down to deal
with this case to avoid a double unpin.
Additionally we need to free the folio if no bio_vec could be added,
and adjust the size of the first bio_vec that contains the bounce buffer
when the I/O size is aligned down.
Fixes: e7b8b3c5b2a6 ("block: align down bounces bios")
Reported-by: 0wnerD1ed <l7z@0b1t.tech>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: 0wnerD1ed <l7z@0b1t.tech>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://patch.msgid.link/20260716091306.316625-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When CONFIG_PERSISTENT_HUGE_ZERO_FOLIO is enabled, iomap_dio_zero() can
add a huge zero folio to a zeroing bio, which needs special treatment
in bio_free_folios by also checking is_huge_zero_folio() in addition to
is_zero_folio().
Fixes: 8dd5e7c75d7b ("block: add helpers to bounce buffer an iov_iter into bios")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Link: https://patch.msgid.link/20260716091306.316625-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When the per-CPU bio cache is enabled but empty, bio_alloc_percpu_cache()
returns NULL and bio_alloc_bioset() falls straight through to the mempool
fallback:
if (unlikely(!bio)) {
if (!(saved_gfp & __GFP_DIRECT_RECLAIM))
return NULL;
...
}
For non-sleeping allocations (no __GFP_DIRECT_RECLAIM) this returns NULL
without ever attempting a slab allocation, even when there is plenty of
free memory.
Commit b520c4eef83d ("block: split bio_alloc_bioset more clearly into a
fast and slowpath") introduced this. Before it, a percpu cache miss fell
through to mempool_alloc(), which attempted the underlying slab allocation
first and only failed when that slab allocation failed. The restructuring
dropped the slab attempt that non-sleeping callers of a cache-enabled
bioset (such as the default fs_bio_set used by bio_alloc()) relied on.
Try a slab allocation with optimistic GFP_ flags before falling back to
the mempool whenever the bio is still NULL, so both the cache-empty and
non-cache paths share the same slab attempt. This restores the previous
behavior for non-sleeping allocations.
Fixes: b520c4eef83d ("block: split bio_alloc_bioset more clearly into a fast and slowpath")
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260709020145.4011533-1-joseph.qi@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Rules listed through the error_injection debugfs file omit the block
operation they match. As a result, rules that differ only in operation
are indistinguishable even though op is mandatory when adding a rule.
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260715073341.95129-1-liu.yun@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When elevator_change() is called concurrently for the same queue, the
elevator_change_done() function runs concurrently as well. This function
adds or deletes kobjects for the debugfs entry of the queue. Then the
concurrent calls cause memory corruption of the kobjects and result in a
process hang. The core part of the elevator switch is protected by queue
freeze and q->elevator_lock. However, since the commit 559dc11143eb
("block: move elv_register[unregister]_queue out of elevator_lock"), the
elevator_change_done() is not serialized. Hence the memory corruption
and the hang.
The failures are observed when udev-worker writes to a sysfs
queue/scheduler attribute file while the blktests test case block/005
writes to the same attribute file. The failure also can be recreated by
running two processes that write to the same queue/scheduler file
concurrently. The failure is observed since another commit 370ac285f23a
("block: avoid cpu_hotplug_lock depedency on freeze_lock"). This commit
changed the behavior of queue freeze and it unveiled the failure.
Fix the failure by changing elv_iosched_store() to acquire
update_nr_hwq_lock as the writer lock instead of the reader lock. This
serializes the whole elevator switch steps, including the
elevator_change_done() call.
Fixes: 559dc11143eb ("block: move elv_register[unregister]_queue out of elevator_lock")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Link: https://patch.msgid.link/20260716092237.1305030-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
bio_copy_kern() allocates pages that are normally freed by the bio
completion callback. If blk_rq_append_bio() rejects the bio, however,
blk_rq_map_kern() only drops the bio reference. Since bio_put() does not
free pages referenced by the bio vectors, those pages leak.
This can happen when the bio exceeds the queue segment constraints or
when a later mapping cannot be merged into a request built by earlier
calls. Track whether the buffer was copied and free those pages before
dropping the rejected bio.
Fixes: 3a5a39276d2a ("block: allow blk_rq_map_kern to append to requests")
Assisted-by: Codex:gpt-5.6-sol
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260715073518.96042-1-liu.yun@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Oliver Hartkopp <socketcan@hartkopp.net> says:
As sashiko-bot was not able to check the second patch this bundle is
re-posted with b4 preparation.
Link: https://patch.msgid.link/20260712-isotp-fixes-v10-0-793a1b1ce17f@hartkopp.net
[mkl: added stable@k.o on Cc, converted Link: -> Closes:]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The TX state machine (so->tx.state) is driven from three contexts:
sendmsg() claiming and progressing a transfer, the RX path consuming
Flow Control/echo frames, and two hrtimers timing out a stalled
transfer. Mixing a lock-free cmpxchg() claim in sendmsg() with
hrtimer_cancel() calls made under so->rx_lock elsewhere left windows
where a frame or timer callback could act on a state that had already
moved on, corrupting an unrelated transfer.
so->rx_lock now covers the full lifecycle of a TX claim: sendmsg()
takes it to check so->tx.state is ISOTP_IDLE, switch it to
ISOTP_SENDING, bump so->tx_gen and drain the previous transfer's
timers - all as one critical section. isotp_rcv_fc()/isotp_rcv_cf()
already run under this lock via isotp_rcv(), and isotp_rcv_echo() now
takes it itself, so none of them can ever observe a transfer mid-claim.
This also means a transfer can no longer be handed to sendmsg()'s
cleanup paths (signal or send error) while another thread is
concurrently claiming or finishing it, so those paths can cancel
timers and reset the state unconditionally.
isotp_release() claims the socket the same way, so a racing sendmsg()
sees a consistent ISOTP_SHUTDOWN and skips arming its timer or sending.
Only the hrtimer callbacks stay outside so->rx_lock, since they run
under so->rx_lock's cancellation elsewhere and taking it themselves
would deadlock. so->tx_gen lets them recognize whether the transfer
they timed out is still the one currently active, so they don't
report an error against a transfer that has since completed or been
superseded.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Reported-by: sashiko-bot@kernel.org
Closes: https://lore.kernel.org/linux-can/20260710142146.BDAE61F000E9@smtp.kernel.org/
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260712-isotp-fixes-v10-3-793a1b1ce17f@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
isotp_release() looked up the bound network device via dev_get_by_index()
using the stored ifindex. During device unregistration the device is
unlisted from the ifindex hash before the NETDEV_UNREGISTER notifier
chain runs, so a concurrent isotp_release() could find no device, skip
can_rx_unregister() entirely, and still proceed to free the socket.
Since isotp_release() had already removed itself from the isotp
notifier list at that point, isotp_notify() would never get a chance to
clean up either, leaving a stale CAN filter that keeps pointing at the
freed socket.
Fix this the same way raw.c already does: hold a tracked reference to
the bound net_device in the socket (so->dev/so->dev_tracker) from
bind() onward instead of re-resolving it from the ifindex, and
serialize bind()/release() with rtnl_lock() so that so->dev is always
consistent with what the NETDEV_UNREGISTER notifier sees. so->dev
stays valid regardless of ifindex-hash unlisting, and is only ever
cleared by whichever of isotp_release()/isotp_notify() gets there
first, so the filter is always removed exactly once.
isotp_bind() now rejects a (re)bind with -EAGAIN while so->[tx|rx].state
isn't ISOTP_IDLE yet, so a timer left running by a prior
NETDEV_UNREGISTER can't act on a newly bound so->ifindex. Both checks
share the same lock_sock() section, so there is no window in which a
concurrent isotp_notify() clearing so->bound could be missed.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Reported-by: sashiko-bot@kernel.org
Closes: https://lore.kernel.org/linux-can/20260707101420.47F261F000E9@smtp.kernel.org/
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260712-isotp-fixes-v10-2-793a1b1ce17f@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
isotp_notify() unregisters the (RCU) CAN filters via can_rx_unregister()
and clears so->bound without waiting for a grace period. isotp_release()
uses so->bound to decide whether it needs to call synchronize_rcu()
before cancelling so->rxtimer, so when NETDEV_UNREGISTER runs first it
skips that synchronize_rcu() and can cancel the timer while an
in-flight isotp_rcv() is still executing and about to re-arm it via
isotp_send_fc(), leading to a use-after-free timer callback on the
freed socket.
sakisho-bot remarked a problem with rtnl_lock held in isotp_notify(),
therefore make isotp_release() always call synchronize_rcu() before
cancelling the timers, regardless of so->bound. This still closes the
original race (isotp_notify() clearing so->bound without waiting for
in-flight isotp_rcv() callers before isotp_release() cancels the RX
timer) without adding any RCU wait to the netdevice notifier path.
Fixes: 14a4696bc311 ("can: isotp: isotp_release(): omit unintended hrtimer restart on socket release")
Closes: https://lore.kernel.org/linux-can/20260707085210.6B6C01F000E9@smtp.kernel.org/
Reported-by: Nico Yip <zdi-disclosures@trendmicro.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260712-isotp-fixes-v10-1-793a1b1ce17f@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Oliver Hartkopp <socketcan@hartkopp.net> says:
as there were different patches flying arround to fix CAN_BCM issues and AI
assisted stuff pop's up again and again, I've created this collection to be
applied.
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-0-562f7e3e42da@hartkopp.net
[mkl: added stable@k.o on Cc, converted Link: -> Closes:]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
An ANYDEV rx op (ifindex == 0) with an active RX timeout and/or
throttle timer has no defined semantics when matching frames arrive
from several interfaces: bcm_rx_handler() can run concurrently for
the same op on different CPUs, racing hrtimer_cancel()/
bcm_rx_starttimer() against bcm_rx_timeout_handler() and causing
spurious RX_TIMEOUT notifications and last_frames corruption. The
same concurrency lets throttled multiplex frames from different
interfaces clobber the single rx_ifindex/rx_stamp fields shared by
the op.
Add op->if_detected to track the first interface that delivers a
matching frame while a timeout/throttle timer is configured, and
reject frames from any other interface for that op. The claim is
decided in bcm_rx_handler() before hrtimer_cancel() touches
op->timer, so a rejected frame can never disturb the claimed
interface's watchdog. RTR-mode ops are excluded via RX_RTR_FRAME,
independent of kt_ival1/kt_ival2, since those may briefly hold a
stale value from an earlier non-RTR configuration.
The claim is released in bcm_notify() on NETDEV_UNREGISTER and in
bcm_rx_setup() when SETTIMER reconfigures the timer values.
A (re-)claim is only possible on CAN devices in NETREG_REGISTERED
dev->reg_state to cover the release in bcm_notify() where reg_state
becomes NETREG_UNREGISTERING until synchronize_net().
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol")
Reported-by: sashiko-bot@kernel.org
Closes: https://lore.kernel.org/linux-can/20260709105031.1A39C1F000E9@smtp.kernel.org/
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-11-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
For an rx op subscribed on all interfaces (ifindex == 0), the same op
is registered once in the shared per-netns wildcard filter list, so
bcm_rx_handler() can run concurrently on different CPUs for frames
arriving on different net devices.
op->rx_stamp and op->rx_ifindex were written before bcm_rx_update_lock was
taken, allowing concurrent writers to race each other - including a torn
store of the 64-bit rx_stamp on 32-bit platforms.
Beyond a torn store bcm_send_to_user() must report the timestamp/ifindex
of the very same frame whose content it is delivering. So the assignment
is placed in the same unbroken bcm_rx_update_lock section as the content
comparison.
As a side effect, the RTR-request frame feature (which never reach
bcm_send_to_user()) no longer updates rx_stamp/rx_ifindex, since only
the notification path needs them.
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol")
Reported-by: sashiko-bot@kernel.org
Closes: https://lore.kernel.org/linux-can/20260707145135.5BC831F00A3A@smtp.kernel.org/
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-10-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
RX: an RX_SETUP update(!) for an existing op skipped can_rx_register()
unconditionally, even when a concurrent NETDEV_UNREGISTER had already
torn down its registration (op->rx_reg_dev == NULL). This silently
did not re-enable frame delivery for that updated filter. bcm_rx_setup()
now re-registers in that case, while leaving rx_ops with ifindex = 0
(all CAN devices) which never carry a tracked rx_reg_dev registered as-is.
TX: bcm_notify() only handled bo->rx_ops on NETDEV_UNREGISTER, leaving
tx_ops with an active cyclic transmission re-arming its hrtimer
indefinitely to execute bcm_tx_timeout_handler(). Cancelling the hrtimer
prevents the runaway timer and any injection into a later reused ifindex,
since nothing else calls bcm_can_tx() for the op until an explicit
TX_SETUP update re-arms it.
Unlike bcm_rx_unreg(), which clears the tracked rx_reg_dev for rx_ops,
the ifindex is intentionally left unchanged for tx_ops. bcm_tx_setup()
always rejects ifindex 0, so clearing it would strand the op: neither a
later TX_SETUP (bcm_find_op()) nor TX_DELETE (bcm_delete_tx_op()) could
ever find it again, since both require an exact ifindex match.
Reported-by: sashiko-bot@kernel.org
Closes: https://lore.kernel.org/linux-can/20260708094536.DDF821F00A3A@smtp.kernel.org/
Closes: https://lore.kernel.org/linux-can/20260708154039.347ED1F000E9@smtp.kernel.org/
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-9-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
sashiko-bot remarked a problem with a concurrent device unregistration
in isotp.c which also is present in the bcm.c code. A former fix for raw.c
commit c275a176e4b6 ("can: raw: add missing refcount for memory leak fix")
introduced a netdevice_tracker which solves the issue for bcm.c too.
bcm_release(), bcm_delete_rx_op() and bcm_notifier() relied on
dev_get_by_index(ifindex) to re-find the device for an rx_op before
unregistering its filter. If a concurrent NETDEV_UNREGISTER has already
unlisted the device from the ifindex table, that lookup fails and
can_rx_unregister() is silently skipped, leaving a stale CAN filter
pointing at the soon-to-be-freed bcm_op/socket.
Hold a netdev_hold()/netdev_put() tracked reference on op->rx_reg_dev
from the moment the rx filter is registered in bcm_rx_setup() until it
is unregistered in bcm_rx_unreg(), and use that reference directly in
bcm_release() and bcm_delete_rx_op() instead of re-looking the device
up by ifindex.
Reported-by: sashiko-bot@kernel.org
Closes: https://sashiko.dev/#/patchset/20260707094716.63578-1-socketcan@hartkopp.net
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-8-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
bcm_tx_setup() validates cf->len against the CAN/CAN FD DLC limits
before installing frames for TX_SETUP, but bcm_rx_setup() never did
the same for the RTR-reply frame configured via RX_SETUP with
RX_RTR_FRAME.
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-7-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Stage new CAN frame content for an existing tx op into a kmalloc()'d
buffer and validate it there, mirroring the approach already used in
bcm_rx_setup(). Only copy the validated data into op->frames while
holding op->bcm_tx_lock, so bcm_can_tx() and bcm_tx_timeout_handler()
can no longer observe a partially updated or unvalidated frame.
Add a missing error path for memcpy_from_msg() when copying CAN frame
data from userspace.
Also move the kt_ival1/kt_ival2/ival1/ival2 updates in bcm_tx_setup()
under op->bcm_tx_lock, and read kt_ival1/kt_ival2/count under the same
lock in bcm_tx_set_expiry() and bcm_tx_timeout_handler(), closing the
torn 64-bit ktime_t read on 32-bit platforms.
Fixes: c2aba69d0c36 ("can: bcm: add locking for bcm_op runtime updates")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-6-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
sashiko-bot remarked the missing use of list_add_rcu() in
bcm_[rx|tx]_setup() to have a proper initialized bcm_op structure
when bcm_proc_show() traverses the bcm_op's under rcu_read_lock().
To cover all initial settings of the bcm_op's the list_add_rcu() calls
are moved to the end of the setup code.
While at it, also fix the mirroring removal side: bcm_release() called
bcm_remove_op() - which frees the op via call_rcu() - on ops that were
still linked in bo->tx_ops/bo->rx_ops, without list_del_rcu() first.
Unlink each op with list_del_rcu() before handing it to bcm_remove_op(),
matching the existing pattern in bcm_delete_tx_op()/bcm_delete_rx_op().
Reported-by: sashiko-reviews@lists.linux.dev
Closes: https://lore.kernel.org/linux-can/20260610094654.A1FFE1F00893@smtp.kernel.org/
Fixes: dac5e6249159 ("can: bcm: add missing rcu read protection for procfs content")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-5-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
KCSAN detected a data race within the bcm_rx_handler() when two CAN frames
have been simultaneously received and processed in a single rx op by two
different CPUs.
Use atomic operations with (signed) long data types to access the
statistics in the hot path to fix the KCSAN complaint.
Additionally simplify the update and check of statistics overflow by
using the atomic operations in separate bcm_update_[rx|tx]_stats()
functions. The rx variant runs under bcm_rx_update_lock to prevent
races when resetting the two rx counters; the tx variant runs under
bcm_tx_lock and only needs to guard its own counter's overflow.
As the rx path resets its values already at LONG_MAX / 100, there is
no conflict between the two locking domains (bcm_rx_update_lock vs.
bcm_tx_lock) even for ops that use both paths.
The rx statistics update and the frames_filtered update in
bcm_rx_changed() were previously performed in two separate
bcm_rx_update_lock sections. For an rx op subscribed on all interfaces
(ifindex == 0), bcm_rx_handler() can run concurrently on different
CPUs, so a counter reset by one CPU between these two sections could
leave frames_filtered larger than frames_abs on another CPU, producing
a bogus (even negative) reduction percentage in procfs. Update the
statistics in the same critical section as bcm_rx_changed() to close
this gap, which also removes the now unneeded extra lock/unlock pair
around the traffic_flags calculation.
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-4-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
KCSAN detected a simultaneous access to timer values that can be
overwritten in bcm_rx_setup() when updating timer and filter content
while bcm_rx_handler(), bcm_rx_timeout_handler() or bcm_rx_thr_handler()
run concurrently on incoming CAN traffic.
Protect the timer (ival1/ival2/kt_ival1/kt_ival2/kt_lastmsg) and filter
(nframes/flags/frames/last_frames) updates in bcm_rx_setup() with a new
per-op bcm_rx_update_lock, taken with the matching scope in the RX
handlers. memcpy_from_msg() is staged into a temporary buffer before the
lock is taken, since it can sleep and must not run under a spinlock.
hrtimer_cancel() is always called without bcm_rx_update_lock held, since
bcm_rx_timeout_handler()/bcm_rx_thr_handler() take the same lock and a
running callback would otherwise deadlock against the canceller.
Also close a related race: bcm_rx_setup() cleared the RTR flag in the
stored reply frame's can_id as a separate, unprotected step after the
frame content was already installed, so a concurrent bcm_rx_handler()
could transmit a stale reply with CAN_RTR_FLAG still set. Fold that
normalization into the initial frame preparation instead (on the staged
buffer for updates, directly on op->frames pre-registration for new
ops), so the installed frame is always atomically self-consistent.
bcm_rx_handler()'s RX_RTR_FRAME check now takes a lock-protected
snapshot of op->flags before deciding whether to call bcm_can_tx(),
but does not hold the lock across that call.
Also take a lock-protected snapshot of the currframe in bcm_can_tx()
to avoid partly overwrites by content updates in bcm_tx_setup().
Finally check if a TX_RESET_MULTI_IDX/SETTIMER might have reset
op->currframe between the two locked sections in bcm_can_tx().
Omit calling hrtimer_forward() with zero interval in bcm_rx_thr_handler().
kt_ival2 may have been concurrently cleared by bcm_rx_setup() before it
cancels this timer, so check kt_ival2 inside the bcm_rx_update_lock.
Fixes: c2aba69d0c36 ("can: bcm: add locking for bcm_op runtime updates")
Reported-by: syzbot+75e5e4ae00c3b4bb544e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-can/6975d5cf.a00a0220.33ccc7.0022.GAE@google.com/
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-3-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
bcm_sendmsg() reads bo->ifindex and checks bo->bound before taking
lock_sock(), while bcm_notify(), bcm_connect() and bcm_release() all
mutate both fields under that same lock. Because the lockless reads
and the locked writes are unordered with respect to each other, a
racing bcm_notify() (device unregister) or bcm_connect() (concurrent
bind on another thread sharing the socket) can make bcm_sendmsg()
observe an inconsistent combination, e.g. a stale bound=1 together
with the now-cleared ifindex=0, silently turning a socket bound to a
specific CAN interface into one that also matches "any" interface.
Keep the lockless bo->bound check purely as a fast-path reject, and
move the ifindex read (and a bo->bound re-check) into the locked
section, where every writer already serializes. This removes the
possibility of observing the two fields torn against each other,
rather than trying to fix it with more READ_ONCE()/WRITE_ONCE() pairs
on two independently updated fields. Annotate the now-purely-lockless
bo->bound accesses consistently across all its write sites.
Also fix bcm_rx_setup() silently returning success when the target
device disappears concurrently instead of reporting -ENODEV, so a
broken RX op is no longer left registered as if it had succeeded.
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol")
Reported-by: Ginger <ginger.jzllee@gmail.com>
Closes: https://lore.kernel.org/linux-can/CAGp+u1aBK8QVjsvAxM2Ldzep4rEbsP9x_pV3At4g=h1kVEtyhA@mail.gmail.com/
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-2-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Commit f1b4e32aca08 ("can: bcm: use call_rcu() instead of costly
synchronize_rcu()") replaced synchronize_rcu() in bcm_delete_rx_op()
with call_rcu() and introduced the RX_NO_AUTOTIMER flag.
However, this flag check was omitted for thrtimer in the packet rx
fast-path. During BCM RX operation teardown, a concurrent RCU reader
(bcm_rx_handler) can race and re-arm thrtimer via
bcm_rx_update_and_send() after call_rcu() has been scheduled. Once
the RCU grace period elapses, bcm_op is freed. The subsequently
firing thrtimer then dereferences the deallocated op, causing a UAF.
Adding flag checks to the rx fast-path (bcm_rx_update_and_send) does not
fully close the TOCTOU race and introduces latency for every CAN frame.
Conversely, calling hrtimer_cancel() directly inside the RCU callback
(softirq context) is fatal as hrtimer_cancel() can sleep, triggering
a "scheduling while atomic" panic.
Resolve this by deferring the timer cancellation and memory free to a
dedicated unbound workqueue (bcm_wq). The RCU callback now queues a
work item to bcm_wq, which safely cancels both timers and deallocates
memory in sleepable process context. A dedicated workqueue is used to
prevent system-wide WQ saturation and is cleanly flushed/destroyed
on module unload to avoid rmmod page faults.
Since the deferred work can now outlive the calling context by an
unbounded amount, also take a reference on op->sk when it is assigned
and drop it only once the deferred work has cancelled both timers, so a
socket can no longer be freed out from under a still-armed timer whose
callback (bcm_send_to_user()) dereferences op->sk.
Fixes: f1b4e32aca08 ("can: bcm: use call_rcu() instead of costly synchronize_rcu()")
Tested-by: Feng Xue <feng.xue@outlook.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260714-bcm_fixes-v15-1-562f7e3e42da@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Following the sale of PEAK-System France by HMS-Networks, this update is
intended to change all my @hms-networks.com email addresses to my new
@peak-system.fr address.
Signed-off-by: Stéphane Grosjean <s.grosjean@peak-system.fr>
Link: https://patch.msgid.link/20260410124251.40506-1-stephane.grosjean@free.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
j1939_priv.ents[].nusers is documented as protected by priv->lock, and
its updates already happen under that lock. j1939_can_recv() also reads
it under read_lock_bh(). However, j1939_session_skb_queue() and
j1939_tp_send() still read priv->ents[da].nusers without taking the
lock.
Those transport-side checks decide whether to set J1939_ECU_LOCAL_DST, so
they can race with j1939_local_ecu_get() and j1939_local_ecu_put() while
userspace is binding or releasing sockets concurrently with TP traffic.
This can misclassify TP/ETP sessions as local or remote and take the wrong
transport path.
Fix both transport paths by routing the destination-locality check through
a helper that reads ents[].nusers under read_lock_bh(&priv->lock).
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Shuhao Fu <sfual@cse.ust.hk>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260419140614.GA4041240@chcpu16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
hotplug
If a vCPU stays scheduled out (or blocked) while the last pCPU it ran
on goes through a hotplug cycle (online->offline->online), and the vCPU
then resumes execution on the same pCPU, then it is possible for it to
run with an ASID that has now been assigned to a different vCPU,
resulting in stale TLB translations being used.
svm_enable_virtualization_cpu() resets asid_generation to 1 and sets
next_asid to max_asid + 1 on every CPU online event, including hotplug
cycles. Because next_asid starts beyond the pool boundary, the first
call to new_asid() after an online event always wraps the pool,
incrementing asid_generation to 2 and assigning ASIDs starting from
min_asid.
Consider two vCPUs from different VMs, vCPU-A pinned to CPU-X holding
asid_generation=2 and ASID=N from before the hotplug event:
1. CPU-X goes offline and back online: asid_generation resets to 1,
next_asid = max_asid + 1.
2. One or more vCPUs migrate to CPU-X and call new_asid(), wrapping
the pool and consuming ASIDs starting from min_asid. Eventually
vCPU-B from a different VM is assigned asid_generation=2, ASID=N
— the same ASID that vCPU-A held before the hotplug.
3. vCPU-A enters pre_svm_run() on CPU-X: current_vmcb->cpu is
unchanged so the migration branch is skipped. Its saved
asid_generation=2 matches sd->asid_generation=2, so the generation
check silently passes and vCPU-A continues running with ASID=N —
the same ASID just freshly assigned to vCPU-B.
Both vCPUs from different VMs now run on CPU-X with the same ASID,
causing them to share NPT TLB entries and producing stale translations.
The collision manifests as a KVM internal error (Suberror: 1, emulation
failure). The NPT page fault reports a faulting GPA far outside the
VM's physical memory range — a sign of stale TLB translations being
used. KVM falls back to instruction emulation, which fails on
FPU/XSave instructions (XRSTOR, STMXCSR) that the emulator does not
implement.
Fix this by incrementing asid_generation instead of resetting it to 1
in svm_enable_virtualization_cpu(). On module load, asid_generation
starts at 0 (memset) and the increment produces 1, identical to the
old behaviour. On subsequent hotplug cycles the generation advances
beyond any value a vCPU previously observed on this CPU, so the
generation check in pre_svm_run() reliably forces new_asid() on every
vCPU after every hotplug cycle.
Fixes: 774c47f1d78e ("[PATCH] KVM: cpu hotplug support")
Reported-by: Chandrakanth Silveru <Chandrakanth.Silveru@amd.com>
Tested-by: Srikanth Aithal <Srikanth.Aithal@amd.com>
Reviewed-by: K Prateek Nayak <kprateek.nayak@amd.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Nikunj A Dadhania <nikunj@amd.com>
Message-ID: <20260715063506.672432-1-nikunj@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit fix from Shuah Khan:
"Fix warning suppressions with kunit built as module:
CONFIG_KUNIT is a tristate symbol but the warning suppression code in
lib/bug.c is only built if it's built-in due to it using a plain
#ifdef, rendering warning suppressions broken for kunit build as
loadable module.
kunit_is_suppressed_warning() already has a stub for when kunit is
disabled so drop that guard entirely"
* tag 'linux_kselftest-kunit-fixes-7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
bug: fix warning suppressions with kunit built as module
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- Fix ftrace reading enabled_func test in add_remove_fprobe_module test
- Fix tracing trigger-hist-poll.tc to use sched_process_exit
* tag 'linux_kselftest-fixes-7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/tracing: Have trigger-hist-poll.tc use sched_process_exit
selftests/ftrace: Fix reading enabled_functions in add_remove_fprobe_module test
|
|
During one of my local btrfs fstests runs, folio_alloc() inside
folio_alloc_greedy() triggered an allocation failure report when trying
to allocate an order-4 folio.
The kernel is from the latest development branch, which is utilizing
the IOMAP_DIO_BOUNCE flag for direct writes when the inode requires
checksum.
Unfortunately I didn't save the full log, only the function and the
order.
When the IOMAP_DIO_BOUNCE flag is utilized, we will hit the following call
chain:
bio_iov_iter_bounce_write()
|- folio_alloc_greedy()
|- folio_alloc(gfp | __GFP_NORETRY, get_order(*size));
However __GFP_NORETRY will still emit an allocation failure report
when it fails.
And folio_alloc_greedy() will retry with a smaller order anyway, there
is no point in emitting that allocation failure report.
Append the __GFP_NOWARN flag to folio_alloc() for the larger-order folio
attempts.
Fixes: 8dd5e7c75d7b ("block: add helpers to bounce buffer an iov_iter into bios")
Signed-off-by: Qu Wenruo <wqu@suse.com>
Link: https://patch.msgid.link/d10571445ee505d95ba6eaad7558fc1f556d2921.1784020005.git.wqu@suse.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
aix_partition() reads the logical-volume descriptor array as a single
sector and then scans it:
if (numlvs && (d = read_part_sector(state, vgda_sector + 1, §))) {
struct lvd *p = (struct lvd *)d;
...
for (i = 0; foundlvs < numlvs && i < state->limit; i++) {
lvip[i].pps_per_lv = be16_to_cpu(p[i].num_lps);
p points at a single 512-byte sector, which holds SECTOR_SIZE /
sizeof(struct lvd) = 16 entries, but the loop runs until foundlvs reaches
the on-disk numlvs or i reaches state->limit (DISK_MAX_PARTS, 256).
numlvs is an on-disk __be16 read straight from the volume group
descriptor and is not validated, so a crafted AIX image with numlvs
larger than 16 and lvd entries whose num_lps fields are zero (so foundlvs
never advances) drives the loop to read p[i] well past the end of the
read sector buffer.
Commit d97a86c170b4 ("partitions: aix.c: off by one bug") hardened the
matching write of lvip[lv_ix] in 2014 but left this read loop unbounded.
Bound the scan to the number of struct lvd entries that fit in the
sector that was actually read.
Fixes: 6ceea22bbbc8 ("partitions: add aix lvm partition support files")
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://patch.msgid.link/20260714114806.3761553-1-michael.bommarito@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When radix_tree_insert() fails in blkg_create(), the error path has two
issues:
1. blkg->online is set to true unconditionally, even when the blkg was
never fully inserted. Move the assignment inside the success block.
2. The error path calls blkg_put() without first calling
percpu_ref_kill(). Because the refcount is still in percpu mode,
percpu_ref_put() only does this_cpu_sub() without checking for zero,
so blkg_release() is never triggered. This permanently leaks the
blkg memory, its percpu iostat, policy data, the parent blkg
reference, and the cgroup css reference — the latter preventing the
cgroup from ever being destroyed.
Fix by replacing blkg_put() with percpu_ref_kill(), matching the pattern
used in blkg_destroy().
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tao Cui <cuitao@kylinos.cn>
Link: https://patch.msgid.link/20260715132407.1469777-1-cui.tao@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 267ec4d7223a ("loop: fix partition scan race between udev and
loop_reread_partitions()") stopped disk_force_media_change() from
setting GD_NEED_PART_SCAN because loop devices with LO_FLAGS_PARTSCAN
rescan partitions explicitly. However, partitions can also be added
manually with BLKPG while LO_FLAGS_PARTSCAN is clear.
When such a loop device is detached, __loop_clr_fd() skips
bdev_disk_changed(). Without GD_NEED_PART_SCAN, reopening the unbound
device no longer performs the previous lazy cleanup, leaving dead
partition devices behind. A subsequent LOOP_CONFIGURE can then fail its
partition scan with -EBUSY, as seen in blktests loop/009 after loop/008.
Call bdev_disk_changed() unconditionally during __loop_clr_fd(). The
disk capacity is already zero and the release path holds open_mutex, so
this drops all partitions without rescanning the detached backing file.
The new blktests loop/013 case covers this sequence by adding a partition
with BLKPG without LO_FLAGS_PARTSCAN, detaching the loop device, and
checking that the partition is gone when the device is reopened.
Fixes: 267ec4d7223a ("loop: fix partition scan race between udev and loop_reread_partitions()")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202607150754.b660f5b9-lkp@intel.com
Signed-off-by: Daan De Meyer <daan@amutable.com>
Link: https://patch.msgid.link/20260715-b4-loop-partition-cleanup-v1-1-b9f59910cd1e@amutable.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
blk_time_get_ns() populates the per-plug cached timestamp and then
returns it by re-reading the field:
if (!plug->cur_ktime) {
plug->cur_ktime = ktime_get_ns();
current->flags |= PF_BLOCK_TS;
}
return plug->cur_ktime;
This is problematic when the compiler emits the final
"return plug->cur_ktime" as a reload from memory, after PF_BLOCK_TS has
already been set.
Since the cached timestamp is now invalidated from finish_task_switch()
(fad156c2af22 "block: invalidate cached plug timestamp after task
switch"), a task preempted between setting PF_BLOCK_TS and that reload
has plug->cur_ktime zeroed by blk_plug_invalidate_ts() when it is
scheduled back in. The reload then returns 0.
A 0 handed back here is stored as a start timestamp -- e.g.
blk_account_io_start() writes it to rq->start_time_ns -- and later
subtracted from "now". blk_account_io_done() then adds (now - 0), i.e.
roughly the system uptime, to the per-group nsecs[] counters. On an
otherwise idle, healthy device this appears as sudden ~uptime-sized jumps
in the diskstats time fields (write_ticks/discard_ticks/time_in_queue).
The solution is to be explicit in our reads and writes to this field
that is preemption volatile. We also add a barrier() to ensure that any
setting of PF_BLOCK_TS is ordered to happen after the cur_ktime update.
This issue was discovered using AI-assisted kprobes looking for paths
that were leaking zeroed timestamps in a live system, based on the
observation that we were sometimes seeing uptime-sized jumps in kernel
exported counters. This was flagged by NodeDiskIOSaturation
prometheus alerts that started firing on all hosts post 7.1.3 kernel
upgrade, due to node-exporter now exporting a nonsensical
node_disk_io_time_weighted_seconds_total.
Fixes: fad156c2af22 ("block: invalidate cached plug timestamp after task switch")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Waychison <mike@waychison.com>
Assisted-by: Claude:claude-opus-4.8
Link: https://patch.msgid.link/20260715192950.2488921-1-mike@waychison.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm SCMI/FF-A fixes for v7.2
Fix two runtime issues in the SCMI framework. Use full 64-bit division
when rounding range-based clock rates, avoiding divisor truncation and
a possible divide-by-zero on 32-bit systems. Rate-limit notification
queue-full warnings emitted from interrupt context to prevent printk
floods and prolonged system stalls during notification bursts. Also
correct a grammar error in the ARM_SCMI_POWER_CONTROL Kconfig help
text.
Fix the FF-A driver RX/TX buffer sizing logic to respect the maximum
buffer size advertised by firmware, while retaining compatibility with
older implementations that may reject PAGE_SIZE-rounded buffers.
Also fix a NULL pointer dereference in ffa_partition_info_get() by
rejecting NULL UUID strings before passing them to uuid_parse().
* tag 'scmi-ffa-fixes-7.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Rate-limit queue-full warnings in IRQ context
firmware: arm_scmi: Use 64-bit division for clock rate rounding
firmware: arm_scmi: Grammar s/may needed/may be needed/
firmware: arm_ffa: Fix NULL dereference in ffa_partition_info_get()
firmware: arm_ffa: Respect firmware advertised RX/TX buffer size limits
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When cpusetsize < cpumask_size(), hwprobe_get_cpus() did not fully
initialize its copy of the cpu mask, which could cause non-deterministic
results from the riscv_hwprobe syscall on a system with more than 8 CPUs
when the supplied cpu mask is empty. Address this by fully initializing
the cpu mask.
Fixes: e178bf146e4b ("RISC-V: hwprobe: Introduce which-cpus flag")
Signed-off-by: Mark Harris <mark.hsj@gmail.com>
Reviewed-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@kernel.org>
Link: https://patch.msgid.link/20260714003056.73707-1-mark.hsj@gmail.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
|
|
ev variable is userspace controlled via event->attr.config and used
as an array index after bounds checking, but without speculation
barriers.
Add the missing array_index_nospec() call to prevent speculative
execution.
Cc: stable@vger.kernel.org
Fixes: 212188a596d1 ("[S390] perf: add support for s390x CPU counters")
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Currently csum_partial() calls csum_copy() with copy=false and dst=NULL.
On machines without the vector facility, csum_copy() falls back to
cksm(dst, ...), causing the checksum to be calculated from address zero
instead of the source buffer.
The VX implementation already checksums data loaded from src. Make the
fallback do the same by passing src to cksm().
Fixes: dcd3e1de9d17 ("s390/checksum: provide csum_partial_copy_nocheck()")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
fw_log_from_bo() validates the tracing buffer header_size and that the
log fits within the BO, but never checks that log->size is at least
log->header_size. fw_log_print_buffer() then computes:
u32 data_size = log->size - log->header_size;
which underflows to a near-U32_MAX value when firmware reports a log whose
size is smaller than its header. That huge data_size defeats the
log_start/log_end bounds clamps added by commit dd1311bcf0e6 ("accel/ivpu:
Add bounds checks for firmware log indices"), so fw_log_print_lines() reads
far past the small real data region of the BO. A size of 0 also makes
fw_log_from_bo() advance the offset by 0, causing the callers to loop
forever on the same header.
Reject logs whose size is smaller than the header (which also rejects
size == 0).
Fixes: d4e4257afa6e ("accel/ivpu: Add firmware tracing support")
Cc: stable@vger.kernel.org
Signed-off-by: Jhonraushan <raushan.jhon@gmail.com>
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Link: https://patch.msgid.link/20260715074206.867712-1-raushan.jhon@gmail.com
|
|
drmm_mutex_init() can fail while registering the managed cleanup action.
When that happens, drmm_add_action_or_reset() destroys the mutex before
returning the error. Continuing initialization would therefore leave the
debugfs GEM object list with an unusable lock.
Propagate the error as is already done for the other managed mutexes in
panthor_device_init().
Fixes: a3707f53eb3f ("drm/panthor: show device-wide list of DRM GEM objects over DebugFS")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patch.msgid.link/20260713082912.321021-1-lilinmao@kylinos.cn
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
panthor_fw_load() detects truncated firmware images, but jumps to the
common cleanup path without setting ret. If no previous error was recorded,
the function can return 0 and treat the invalid firmware as successfully
loaded.
Set ret to -EINVAL before leaving the truncated-image path.
Fixes: 2718d91816ee ("drm/panthor: Add the FW logical block")
Cc: stable@vger.kernel.org
Signed-off-by: Osama Abdelkader <osama.abdelkader@gmail.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patch.msgid.link/20260714163056.22329-1-osama.abdelkader@gmail.com
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
Put all vmcs12 pages if KVM synthesizes a nested VM-Exit due to invalid
guest while emulating VMLAUNCH or VMRESUME. The invalid guest state path
doesn't use nested_vmx_vmexit() as that API is intended to be used if and
only if L2 is active, and the open coded equivalent neglects to put the
vmcs12 pages. Failure to put the vmcs12 pages leaks any pinned pages
(and/or mappings) if L1 retries VMLAUNCH/VMRESUME.
Note, the !from_vmenter scenario doesn't suffer the same problem, as
vmx_get_nested_state_pages() only gets/pins/maps the vmcs12 pages if L2 is
active, i.e. if a "full" VM-Exit is guaranteed before KVM will retry
getting vmcs12 pages.
Fixes: 96c66e87deee ("KVM/nVMX: Use kvm_vcpu_map when mapping the virtual APIC page")
Fixes: 3278e0492554 ("KVM/nVMX: Use kvm_vcpu_map when mapping the posted interrupt descriptor table")
Fixes: fe1911aa443e ("KVM: nVMX: Use kvm_vcpu_map() to get/pin vmcs12's APIC-access page")
Reported-by: Minh Nguyen <minhnguyen.080505@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fixes for 7.2
- more gmap KVM memory management fixes
- PCI passthru fixes
|
|
KVM x86 fixes for 7.2-rcN
- Fix a bug where KVM will trigger a UAF if updating IOMMU IRTEs fails when
registering an IRQ-bypass producer.
- Ignore pending PV EOI instead of BUG()ing the host if the feature was
disabled by the guest.
- Fix nVMX bugs where KVM would run L1 with an L1-controlled CR3 after a
failed "late" consistency check when KVM is NOT using EPT.
- Disallow intra-host migration/mirroring of SNP VMs as KVM doesn't yet
support moving/mirroring SNP state.
- Fix a TOCTOU bug in KVM's handling of the "trusted" CPUID for TDX guests.
- Fix a NULL pointer deref in trace_kvm_inj_exception() where a change to the
core infrastructure missed KVM's unique (ab)use of __print_symbolic().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 7.2, take #2
- Move locking for kvm_io_bus_get_dev() into the caller, ensuring
race-free checks that the returned object is of the correct type
- Fix initialisation of the page-table walk level when relaxing
permissions
- Correctly update the XN attribute when relaxing permissions
- Fix the sign extension of loads from emulated MMIO regions
- Assorted collection of fixes for pKVM's FFA proxy, together with a
couple of FFA driver adjustments
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 7.2, take #1
- Fix an accounting buglet when reclaiming pages from a protected
guest
- Fix a bunch of architectural compliance issues when injecting a
synthesised exception, most of which were missing the PSTATE.IL bit
indicating a 32bit-wide instruction
- Another set of fixes addressing issues with translation of VNCR_EL2,
including corner cases where the guest point that register at a RO
page...
- Don't warn when trapping accesses to ZCR_EL2 from an L2 guest, as
that's not unexpected at all
- Address a bunch of races with LPI migration vs LPIs being disabled
- Fix a total howler of a bug combining FEAT_MOPS and NV, resulting in
exception returning in the wrong place...
- Coerce Fuad Tabba into a reviewer role, and may his Inbox catch
fire!
|
|
Sun Jian says:
====================
bpf: Reject negative const offsets for buffer pointers
Reject negative effective offsets for PTR_TO_TP_BUFFER and PTR_TO_BUF
accesses. Calculate the effective access start using signed arithmetic
to prevent unsigned access-end accounting from wrapping, and cover both
load-time rejection and the raw tracepoint writable attach-time path.
---
Changes in v5:
- Simplify __check_buffer_access() to reject a negative effective start
after confirming that var_off is constant. Validate the combined
offset instead of rejecting negative instruction offsets separately.
Drop the duplicate BPF_MAX_VAR_OFF check because pointer arithmetic
already bounds constant offsets, and remove the redundant size < 0
check.
- Switch the raw tracepoint writable attach tests from nbd_send_request
to bpf_testmod_test_writable_bare_tp, avoiding the NBD configuration
dependency and its false-pass condition.
- Split the attach coverage into named subtests and require
bpf_raw_tracepoint_open() to return -EINVAL.
- Add verifier coverage for a negative constant PTR_TO_BUF offset.
Changes in v4:
- Correct the Fixes tag to point to 022ac0750883, where pointer offsets
were folded into reg->var_off.
- Drop the end > U32_MAX check, which is unreachable after bounding const
var_off with BPF_MAX_VAR_OFF while keeping instruction offsets and
access sizes bounded.
Changes in v3:
- Check constant var_off against +/-BPF_MAX_VAR_OFF before computing
the effective access range, matching the existing verifier pointer
offset convention.
- Keep explicit rejection of negative instruction offsets and keep
bounded negative constant var_off valid when the effective offset is
non-negative.
Changes in v2:
- Split the kernel fix and selftests into separate patches.
- Add an attach-time raw tracepoint writable test that exercises
max_tp_access against nbd_send_request's writable size.
- Adjust selftest formatting to use the 100 character line width.
Tested:
- ./test_progs -v -t verifier_raw_tp_writable
- ./test_progs -v -t verifier_ptr_to_buf
- ./test_progs -v -t raw_tp_writable_reject_bad_access
- ./test_progs -v -t raw_tp_writable_test_run
v4: https://lore.kernel.org/bpf/20260708090151.151729-1-sun.jian.kdev@gmail.com/
v3: https://lore.kernel.org/bpf/20260708040715.116680-1-sun.jian.kdev@gmail.com/
v2: https://lore.kernel.org/bpf/20260707060804.93561-1-sun.jian.kdev@gmail.com/
v1: https://lore.kernel.org/bpf/20260703035137.109608-1-sun.jian.kdev@gmail.com/
====================
Link: https://patch.msgid.link/20260714093846.18159-1-sun.jian.kdev@gmail.com
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
|
