Newer binutils (>= 2.36) refuse to assemble lmw/stmw when building in
little endian mode. That breaks compilation of our alignment handler
test:

  /tmp/cco4l14N.s: Assembler messages:
  /tmp/cco4l14N.s:1440: Error: `lmw' invalid when little-endian
  /tmp/cco4l14N.s:1814: Error: `stmw' invalid when little-endian
  make[2]: *** [../../lib.mk:139: /output/kselftest/powerpc/alignment/alignment_handler] Error 1

These tests do pass on little endian machines, as the kernel will
still emulate those instructions even when running little
endian (which is arguably a kernel bug).

But we don't really need to test that case, so ifdef those
instructions out to get the alignment test building again.

Reported-by: Libor Pechacek <lpechacek@suse.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Libor Pechacek <lpechacek@suse.com>
Link: https://lore.kernel.org/r/20210119041800.3093047-1-mpe@ellerman.id.au

Since main() does not return a value explicitly, the
return values from FAIL_IF() conditions are ignored
and the tests can still pass irrespective of failures.
This makes sure that we always explicitly return the
correct test exit status.

Fixes: 1addb6444791 ("selftests/powerpc: Add test for execute-disabled pkeys")
Fixes: c27f2fd1705a ("selftests/powerpc: Add test for pkey siginfo verification")
Reported-by: Eirik Fuller <efuller@redhat.com>
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210118093145.10134-1-sandipan@linux.ibm.com

Patch fixes uninitialized variable warning in bad_accesses test
which causes the selftests build to fail in older distibutions

bad_accesses.c: In function ‘bad_access’:
bad_accesses.c:52:9: error: ‘x’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
   printf("Bad - no SEGV! (%c)\n", x);
         ^
cc1: all warnings being treated as errors

Signed-off-by: Harish <harish@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201201092403.238182-1-harish@linux.ibm.com

I did an in-place build of the self-tests and found that it left
the tree dirty.

Add missed test binaries to .gitignore

Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201201144427.1228745-1-dja@axtens.net

Merge our fixes branch, in particular to bring in the changes for the
entry/uaccess flush.

For simplicity in backporting, the original entry_flush test contained
a lot of duplicated code from the rfi_flush test. De-duplicate that code.

Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add a test modelled on the RFI flush test which counts the number
of L1D misses doing a simple syscall with the entry flush on and off.

For simplicity of backporting, this test duplicates a lot of code from
rfi_flush. We clean that up in the next patch.

Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We are about to add an entry flush. The rfi (exit) flush test measures
the number of L1D flushes over a syscall with the RFI flush enabled and
disabled. But if the entry flush is also enabled, the effect of enabling
and disabling the RFI flush is masked.

If there is a debugfs entry for the entry flush, disable it during the RFI
flush and restore it later.

Reported-by: Spoorthy S <spoorts2@in.ibm.com>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The eeh-basic test got its own 60 seconds timeout (defined in commit
414f50434aa2 "selftests/eeh: Bump EEH wait time to 60s") per breakable
device.

And we have discovered that the number of breakable devices varies
on different hardware. The device recovery time ranges from 0 to 35
seconds. In our test pool it will take about 30 seconds to run on a
Power8 system that with 5 breakable devices, 60 seconds to run on a
Power9 system that with 4 breakable devices.

Extend the timeout setting in the kselftest framework to 5 minutes
to give it a chance to finish.

Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201023024539.9512-1-po-hsu.lin@canonical.com

Pull powerpc fixes from Michael Ellerman:

 - A fix for undetected data corruption on Power9 Nimbus <= DD2.1 in the
   emulation of VSX loads. The affected CPUs were not widely available.

 - Two fixes for machine check handling in guests under PowerVM.

 - A fix for our recent changes to SMP setup, when
   CONFIG_CPUMASK_OFFSTACK=y.

 - Three fixes for races in the handling of some of our powernv sysfs
   attributes.

 - One change to remove TM from the set of Power10 CPU features.

 - A couple of other minor fixes.

Thanks to: Aneesh Kumar K.V, Christophe Leroy, Ganesh Goudar, Jordan
Niethe, Mahesh Salgaonkar, Michael Neuling, Oliver O'Halloran, Qian Cai,
Srikar Dronamraju, Vasant Hegde.

* tag 'powerpc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Avoid using addr_to_pfn in real mode
  powerpc/uaccess: Don't use "m<>" constraint with GCC 4.9
  powerpc/eeh: Fix eeh_dev_check_failure() for PE#0
  powerpc/64s: Remove TM from Power10 features
  selftests/powerpc: Make alignment handler test P9N DD2.1 vector CI load workaround
  powerpc: Fix undetected data corruption with P9N DD2.1 VSX CI load emulation
  powerpc/powernv/dump: Handle multiple writes to ack attribute
  powerpc/powernv/dump: Fix race while processing OPAL dump
  powerpc/smp: Use GFP_ATOMIC while allocating tmp mask
  powerpc/smp: Remove unnecessary variable
  powerpc/mce: Avoid nmi_enter/exit in real mode on pseries hash
  powerpc/opal_elog: Handle multiple writes to ack attribute