linux-stable.git/tools/testing/selftests/drivers/net, branch v6.2

selftests: ocelot: tc_flower_chains: make test_vlan_ingress_modify() more comprehensive

2023-02-07T11:20:21+00:00

We have two IS1 filters of the OCELOT_VCAP_KEY_ANY key type (the one with
"action vlan pop" and the one with "action vlan modify") and one of the
OCELOT_VCAP_KEY_IPV4 key type (the one with "action skbedit priority").
But we have no IS1 filter with the OCELOT_VCAP_KEY_ETYPE key type, and
there was an uncaught breakage there.

To increase test coverage, convert one of the OCELOT_VCAP_KEY_ANY
filters to OCELOT_VCAP_KEY_ETYPE, by making the filter also match on the
MAC SA of the traffic sent by mausezahn, $h1_mac.

Signed-off-by: Vladimir Oltean 
Link: https://lore.kernel.org/r/20230205192409.1796428-2-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni

selftests: devlink: add a warning for interfaces coming up

2022-12-16T10:21:37+00:00

NetworkManager (and other daemons) may bring the interface up
and cause failures in quiescence checks. Print a helpful warning,
and take the interface down again.

I seem to forget about this every time I run these tests on a new VM.

Signed-off-by: Jakub Kicinski 
Signed-off-by: David S. Miller

selftests: devlink: fix the fd redirect in dummy_reporter_test

2022-12-16T10:21:36+00:00

$number + > bash means redirect FD $number, e.g. commonly
used 2> redirects stderr (fd 2). The test uses 8192> to
write the number 8192 to a file, this results in:

  ./devlink.sh: line 499: 8192: Bad file descriptor

Oddly the test also papers over this issue by checking
for failure (expecting an error rather than success)
so it passes, anyway.

Fixes: ff18176ad806 ("selftests: Add a test of large binary to devlink health test")
Signed-off-by: Jakub Kicinski 
Signed-off-by: David S. Miller

selftests: bonding: add bonding prio option test

2022-12-14T03:19:54+00:00

Add a test for bonding prio option. Here is the test result:

]# ./option_prio.sh
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=arp_ip_target and primary_reselect=0)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=arp_ip_target and primary_reselect=1)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=arp_ip_target and primary_reselect=2)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=miimon and primary_reselect=0)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=miimon and primary_reselect=1)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=miimon and primary_reselect=2)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=5 monitor=miimon and primary_reselect=0)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=5 monitor=miimon and primary_reselect=1)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=5 monitor=miimon and primary_reselect=2)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=6 monitor=miimon and primary_reselect=0)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=6 monitor=miimon and primary_reselect=1)  [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=6 monitor=miimon and primary_reselect=2)  [ OK ]

Signed-off-by: Liang Li 
Signed-off-by: Hangbin Liu 
Signed-off-by: Jakub Kicinski

selftests: mlxsw: Move IPv6 decap_error test to shared directory

2022-12-09T02:46:32+00:00

Now that Spectrum-1 gained ip6gre support we can move the test out of
the Spectrum-2 directory.

Signed-off-by: Ido Schimmel 
Reviewed-by: Amit Cohen 
Signed-off-by: Petr Machata 
Signed-off-by: Jakub Kicinski

selftests: bonding: up/down delay w/ slave link flapping

2022-11-24T04:14:48+00:00

Verify when a bond is configured with {up,down}delay and the link state
of slave members flaps if there are no remaining members up the bond
should immediately select a member to bring up. (from bonding.txt
section 13.1 paragraph 4)

Suggested-by: Liang Li 
Signed-off-by: Jonathan Toppins 
Signed-off-by: Jakub Kicinski

selftests: mlxsw: Add a test for invalid locked bridge port configurations

2022-11-10T03:06:16+00:00

Test that locked bridge port configurations that are not supported by
mlxsw are rejected.

Signed-off-by: Ido Schimmel 
Reviewed-by: Petr Machata 
Signed-off-by: Petr Machata 
Reviewed-by: Vladimir Oltean 
Signed-off-by: Jakub Kicinski

selftests: mlxsw: Add a test for locked port trap

2022-11-10T03:06:16+00:00

Test that packets received via a locked bridge port whose {SMAC, VID}
does not appear in the bridge's FDB or appears with a different port,
trigger the "locked_port" packet trap.

Signed-off-by: Ido Schimmel 
Reviewed-by: Petr Machata 
Signed-off-by: Petr Machata 
Reviewed-by: Vladimir Oltean 
Signed-off-by: Jakub Kicinski

selftests: mlxsw: Add a test for EAPOL trap

2022-11-10T03:06:16+00:00

Test that packets with a destination MAC of 01:80:C2:00:00:03 trigger
the "eapol" packet trap.

Signed-off-by: Ido Schimmel 
Reviewed-by: Petr Machata 
Signed-off-by: Petr Machata 
Reviewed-by: Vladimir Oltean 
Signed-off-by: Jakub Kicinski

selftests: net: Fix netdev name mismatch in cleanup

2022-10-21T04:09:22+00:00

lag_lib.sh creates the interfaces dummy1 and dummy2 whereas
dev_addr_lists.sh:destroy() deletes the interfaces dummy0 and dummy1. Fix
the mismatch in names.

Fixes: bbb774d921e2 ("net: Add tests for bonding and team address list management")
Signed-off-by: Benjamin Poirier 
Reviewed-by: Jonathan Toppins 
Signed-off-by: Jakub Kicinski