Pull x86 platform driver updates from Andy Shevchenko:

 - New bootctl driver for Mellanox BlueField SoC.

 - New driver to support System76 laptops.

 - Temperature monitoring and fan control on Acer Aspire 7551 is now
   supported.

 - Previously the Huawei driver handled only hotkeys. After the
   conversion to WMI it has been expanded to support newer laptop
   models.

 - Big refactoring of intel-speed-select tools allows to use it on Intel
   CascadeLake-N systems.

 - Touchscreen support for ezpad 6 m4 and Schneider SCT101CTM tablets

 - Miscellaneous clean ups and fixes here and there.

* tag 'platform-drivers-x86-v5.5-1' of git://git.infradead.org/linux-platform-drivers-x86: (59 commits)
  platform/x86: hp-wmi: Fix ACPI errors caused by passing 0 as input size
  platform/x86: hp-wmi: Fix ACPI errors caused by too small buffer
  platform/x86: intel_pmc_core: Add Comet Lake (CML) platform support to intel_pmc_core driver
  platform/x86: intel_pmc_core: Fix the SoC naming inconsistency
  platform/mellanox: Fix Kconfig indentation
  tools/power/x86/intel-speed-select: Display TRL buckets for just base config level
  tools/power/x86/intel-speed-select: Ignore missing config level
  platform/x86: touchscreen_dmi: Add info for the ezpad 6 m4 tablet
  tools/power/x86/intel-speed-select: Increment version
  tools/power/x86/intel-speed-select: Use core count for base-freq mask
  tools/power/x86/intel-speed-select: Support platform with limited Intel(R) Speed Select
  tools/power/x86/intel-speed-select: Use Frequency weight for CLOS
  tools/power/x86/intel-speed-select: Make CLOS frequency in MHz
  tools/power/x86/intel-speed-select: Use mailbox for CLOS_PM_QOS_CONFIG
  tools/power/x86/intel-speed-select: Auto mode for CLX
  tools/power/x86/intel-speed-select: Correct CLX-N frequency units
  tools/power/x86/intel-speed-select: Change display of "avx" to "avx2"
  tools/power/x86/intel-speed-select: Extend command set for perf-profile
  Add touchscreen platform data for the Schneider SCT101CTM tablet
  platform/x86: intel_int0002_vgpio: Pass irqchip when adding gpiochip
  ...

When only base config level is present, this tool is displaying TRL
(Turbo-ratio-limits) by reading legacy MSR. In this case, also present
core count for TRL by reading MSR 0x1AE.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

It is possible that certain config levels are not available, even
if the max level includes the level. There can be missing levels in
some platforms. So ignore the level when called for information dump
for all levels and fail if specifically ask for the missing level.

Here the changes is to continue reading information about other levels
even if we fail to get information for the current level. But use the
"processed" flag to indicate the failure. When the "processed" flag is
not set, don't dump information about that level.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Since the tool now adds support for another Intel SST implementation,
increment version number.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Some firmware implementation gives error when a command is sent get mask
for core count 32-61. So use core count to decide.

But there is no function to get core count. So introduce one function to
get core count.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There are some platforms, where there limited support of Intel(R) SST
features. Here perf-profile has only one base configuration and limited
support of commands. But still has support for discovery of base-freq and
turbo-freq features. So it is important to show minimum features to use
base-freq and turbo-freq features.

Here the change are:
- When there is no support of CONFIG_TDP_GET_LEVELS_INFO, then instead
of treating this as fatal error, treat this with number of config levels
= 0, that means only base level 0 is present.
- There is no support of mail box commands to get base frequencies or
turbo frequencies. Here present base frequency by reading cpufreq
base freq and turbo frequency by reading MSR 0x1AD.
- Don't display any field, which has value == 0.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Use different frequency weights for CLOS 0 and and CLOS1-3, to define
relative priority for power budgeting. This will be used for --auto
mode to enable base-freq and turbo-freq feature.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

To be consistant with the other frequency units, change the CLOS
unit to MHz instead of ratios.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Use mailbox to read/write CLOS_PM_QOS_CONFIG instead of read/write to
MMIO offset.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is an expectation in the CLX platform for SST base-freq feature that
Scaling min frequency be different for high and low priority cores.
This is the way the firmware will understand the priority.

So this change will look at high priority and low priority cores, and set
scaling_min_freq to P1High for high priority cores and P1Low to low
priority cores.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>