The switch that conditionally sets CPUPOWER_CAP_HAS_TURBO_RATIO and
CPUPOWER_CAP_IS_SNB flags is missing a break, so all cores get both
flags set and an assumed base clock of 100 MHz for turbo values.

Reported-by: GSR <gsr.bugs@infernal-iceberg.com>
Tested-by: GSR <gsr.bugs@infernal-iceberg.com>
References: https://bugs.debian.org/859978
Fixes: 8fb2e440b223 (cpupower: Show Intel turbo ratio support via ...)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull turbostat utility fixes for v4.11 from Len Brown.

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: update version number
  tools/power turbostat: fix impossibly large CPU%c1 value
  tools/power turbostat: turbostat.8 add missing column definitions
  tools/power turbostat: update HWP dump to decimal from hex
  tools/power turbostat: enable package THERM_INTERRUPT dump
  tools/power turbostat: show missing Core and GFX power on SKL and KBL
  tools/power turbostat: bugfix: GFXMHz column not changing

Signed-off-by: Len Brown <len.brown@intel.com>

Most CPUs do not have a hardware c1 counter,
and so turbostat derives c1 residency:

c1 = TSC - MPERF - other_core_cstate_counters

As it is not possible to atomically read these coutners,
measurement jitter can case this calcuation to "go negative"
when very close to 0.  Turbostat detect that case and
simply prints c1 = 0.00%

But that check neglected to account for systems where the TSC
crystal clock domain and the MPERF BCLK domain are differ by
a small amount.  That allowed very small negative c1 numbers
to escape this check and be printed as huge positve numbers.

This code begs for a bit of cleanup, but this patch
is the minimal change to fix the issue.

Signed-off-by: Len Brown <len.brown@intel.com>

Add GFX%rc6 and GFXMHz to the column descriptions section
of the turbostat man page.

Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Len Brown <len.brown@intel.com>

Syntax only.

The HWP CAPABILTIES and REQUEST ratios are more easily
viewed in decimal -- just multiply by 100 and you get MHz...

new:
cpu0: MSR_HWP_CAPABILITIES: 0x010c1b23 (high 35 guar 27 eff 12 low 1)
cpu0: MSR_HWP_REQUEST: 0x80002301 (min 1 max 35 des 0 epp 0x80 window 0x0 pkg 0x0)

old:
cpu0: MSR_HWP_CAPABILITIES: 0x010c1b23 (high 0x23 guar 0x1b eff 0xc low 0x1)
cpu0: MSR_HWP_REQUEST: 0x80002301 (min 0x1 max 0x23 des 0x0 epp 0x80 window 0x0 pkg 0x0)

Signed-off-by: Len Brown <len.brown@intel.com>

cpu0: MSR_IA32_TEMPERATURE_TARGET: 0x00641400 (100 C)
cpu0: MSR_IA32_PACKAGE_THERM_STATUS: 0x884b0800 (25 C)
cpu0: MSR_IA32_PACKAGE_THERM_INTERRUPT: 0x00000003 (100 C, 100 C)

Enable the same per-core output, but hide it behind --debug
because it is too verbose on big systems.

Signed-off-by: Len Brown <len.brown@intel.com>

While the current SDM is silent on the matter, the Core and GFX
RAPL power meters on SKL and KBL appear to work -- so show them.

Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>

turbostat displays a GFXMHz column, which comes from reading
/sys/class/graphics/fb0/device/drm/card0/gt_cur_freq_mhz

But GFXMHz was not changing, even when a manual
cat /sys/class/graphics/fb0/device/drm/card0/gt_cur_freq_mhz
showed a new value.

It turns out that a rewind() on the open file is not sufficient,
fflush() (or a close/open) is needed to read fresh values.

Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Pull turbostat utility updates from Rafael Wysocki:
 "Power management turbostat utility updates.

  These update turbostat significantly and in particular:

   - default output is now verbose, --debug is no longer required to get
     all counters. As a result, some options have been added to specify
     exactly what output is wanted.

   - added --quiet to skip system configuration output

   - added --list, --show and --hide parameters

   - added --cpu parameter

   - enhanced Baytrail SoC support

   - added Gemini Lake SoC support

   - added sysfs C-state columns

  Also the symbol definitions in arch/x86/include/asm/intel-family.h and
  arch/x86/include/asm/msr-index.h are updated and the intel_idle and
  intel_pstate drivers are modified to use the updated symbols.

  Credits to Len Brown for all of these changes"

* tag 'pm-turbostat-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (44 commits)
  tools/power turbostat: version 17.02.24
  tools/power turbostat: bugfix: --add u32 was printed as u64
  tools/power turbostat: show error on exec
  tools/power turbostat: dump p-state software config
  tools/power turbostat: show package number, even without --debug
  tools/power turbostat: support "--hide C1" etc.
  tools/power turbostat: move --Package and --processor into the --cpu option
  tools/power turbostat: turbostat.8 update
  tools/power turbostat: update --list feature
  tools/power turbostat: use wide columns to display large numbers
  tools/power turbostat: Add --list option to show available header names
  tools/power turbostat: fix zero IRQ count shown in one-shot command mode
  tools/power turbostat: add --cpu parameter
  tools/power turbostat: print sysfs C-state stats
  tools/power turbostat: extend --add option to accept /sys path
  tools/power turbostat: skip unused counters on BDX
  tools/power turbostat: fix decoding for GLM, DNV, SKX turbo-ratio limits
  tools/power turbostat: skip unused counters on SKX
  tools/power turbostat: Denverton: use HW CC1 counter, skip C3, C7
  tools/power turbostat: initial Gemini Lake SOC support
  ...