linux-stable.git/sound, branch v6.3.7

ALSA: oss: avoid missing-prototype warnings

2023-06-09T08:48:09+00:00

[ Upstream commit 040b5a046a9e18098580d3ccd029e2318fca7859 ]

Two functions are defined and used in pcm_oss.c but also optionally
used from io.c, with an optional prototype. If CONFIG_SND_PCM_OSS_PLUGINS
is disabled, this causes a warning as the functions are not static
and have no prototype:

sound/core/oss/pcm_oss.c:1235:19: error: no previous prototype for 'snd_pcm_oss_write3' [-Werror=missing-prototypes]
sound/core/oss/pcm_oss.c:1266:19: error: no previous prototype for 'snd_pcm_oss_read3' [-Werror=missing-prototypes]

Avoid this by making the prototypes unconditional.

Signed-off-by: Arnd Bergmann 
Link: https://lore.kernel.org/r/20230516195046.550584-2-arnd@kernel.org
Signed-off-by: Takashi Iwai 
Signed-off-by: Sasha Levin

ASoC: SOF: pm: save io region state in case of errors in resume

2023-06-09T08:48:06+00:00

[ Upstream commit 171b53be635ac15d4feafeb33946035649b1ca14 ]

If there are failures in DSP runtime resume, the device state will not
reach active and this makes it impossible e.g. to retrieve a possible
DSP panic dump via "exception" debugfs node. If
CONFIG_SND_SOC_SOF_DEBUG_ENABLE_DEBUGFS_CACHE=y is set, the data in
cache is stale. If debugfs cache is not used, the region simply cannot
be read.

To allow debugging these scenarios, update the debugfs cache contents in
resume error handler. User-space can then later retrieve DSP panic and
other state via debugfs (requires SOF debugfs cache to be enabled in
build).

Reported-by: Curtis Malainey

ASoC: SOF: sof-client-probes: fix pm_runtime imbalance in error handling

2023-06-09T08:48:06+00:00

[ Upstream commit bc424273c74c1565c459c8f2a6ed95caee368d0a ]

When an error occurs, we need to make sure the device can pm_runtime
suspend instead of keeping it active.

Signed-off-by: Pierre-Louis Bossart

ASoC: SOF: pcm: fix pm_runtime imbalance in error handling

2023-06-09T08:48:06+00:00

[ Upstream commit da0fe8fd515a471d373acc3682bfb5522cca4d55 ]

When an error occurs, we need to make sure the device can pm_runtime
suspend instead of keeping it active.

Signed-off-by: Pierre-Louis Bossart

ASoC: SOF: debug: conditionally bump runtime_pm counter on exceptions

2023-06-09T08:48:05+00:00

[ Upstream commit 3de975862f985f1c9e225a0d13aa3d501373f7c3 ]

When a firmware IPC error happens during a pm_runtime suspend, we
ignore the error and suspend anyways. However, the code
unconditionally increases the runtime_pm counter. This results in a
confusing configuration where the code will suspend, resume but never
suspend again due to the use of pm_runtime_get_noresume().

The intent of the counter increase was to prevent entry in D3, but if
that transition to D3 is already started it cannot be stopped. In
addition, there's no point in that case in trying to prevent anything,
the firmware error is handled and the next resume will re-initialize
the firmware completely.

This patch changes the logic to prevent suspend when the device is
pm_runtime active and has a use_count > 0.

Signed-off-by: Pierre-Louis Bossart

ASoC: ssm2602: Add workaround for playback distortions

2023-06-09T08:48:03+00:00

[ Upstream commit f63550e2b165208a2f382afcaf5551df9569e1d4 ]

Apply a workaround for what appears to be a hardware quirk.

The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.

This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).

Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
        i2cset -y 0 0x1a $(($1*2)) $2
}

For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x87 # out, dac
  ssmset 0x06 0x07 # chip
  OK

  (disable MCLK)
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x1f # chip
  ssmset 0x06 0x07 # out, dac
  (enable MCLK)
  OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x1f # chip
  ssmset 0x06 0x07 # out, dac
  NOT OK

  ssmset 0x06 0x1f # chip
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # out, dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x0f # chip, out
  ssmset 0x06 0x07 # dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x17 # chip, dac
  ssmset 0x06 0x07 # out
  NOT OK

For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  OK

  (disable MCLK)
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  (enable MCLK after reset)
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x17 # chip, dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x0f # chip, out
  NOT OK

  ssmset 0x06 0x07 # chip, out, dac
  NOT OK

Signed-off-by: Paweł Anikiel

ALSA: hda/realtek: Add quirks for ASUS GU604V and GU603V

2023-06-09T08:48:03+00:00

[ Upstream commit 4b963ae1df6426f0e51de64133d379d9bde50c48 ]

These models use 2 CS35L41 amplifiers using SPI for down-facing
speakers.

alc285_fixup_speaker2_to_dac1 is needed to fix volume control of the
down-facing speakers.

Pin configs are needed to enable headset mic detection.

Note that these models lack the ACPI _DSD properties needed to
initialize the amplifiers. They can be added during boot to get working
sound out of the speakers:
  https://gist.github.com/lamperez/862763881c0e1c812392b5574727f6ff

Signed-off-by: Alexandru Sorodoc 
Link: https://lore.kernel.org/r/20230511161510.315170-1-ealex95@gmail.com
Signed-off-by: Takashi Iwai 
Signed-off-by: Sasha Levin

ASoC: jz4740-i2s: Make I2S divider calculations more robust

2023-06-09T08:48:03+00:00

[ Upstream commit ad721bc919edfd8b4b06977458a412011e2f0c50 ]

When the CPU supplies bit/frame clocks, the system clock (clk_i2s)
is divided to produce the bit clock. This is a simple 1/N divider
with a fairly limited range, so for a given system clock frequency
only a few sample rates can be produced. Usually a wider range of
sample rates is supported by varying the system clock frequency.

The old calculation method was not very robust and could easily
produce the wrong clock rate, especially with non-standard rates.
For example, if the system clock is 1.99x the target bit clock
rate, the divider would be calculated as 1 instead of the more
accurate 2.

Instead, use a more accurate method that considers two adjacent
divider settings and selects the one that produces the least error
versus the requested rate. If the error is 5% or higher then the
rate setting is rejected to prevent garbled audio.

Skip divider calculation when the codec is supplying both the bit
and frame clock; in that case, the divider outputs are unused and
we don't want to constrain the sample rate.

Signed-off-by: Aidan MacDonald

ASoC: SOF: amd: Fix NULL pointer crash in acp_sof_ipc_msg_data function

2023-06-09T08:48:02+00:00

[ Upstream commit 051d71e073614a72ad423d6dacba37a7eeff274d ]

Check substream and runtime variables before assigning.

Signed-off-by: V sujith kumar Reddy

ASoC: dwc: limit the number of overrun messages

2023-06-09T08:48:02+00:00

[ Upstream commit ab6ecfbf40fccf74b6ec2ba7ed6dd2fc024c3af2 ]

On slow CPU (FPGA/QEMU emulated) printing overrun messages from
interrupt handler to uart console may leads to more overrun errors.
So use dev_err_ratelimited to limit the number of error messages.

Signed-off-by: Maxim Kochetkov