linux-stable.git/net/wireless/core.c, branch v4.4.271

cfg80211: fix memory leak of wiphy device name

2019-07-10T07:56:34+00:00

commit 4f488fbca2a86cc7714a128952eead92cac279ab upstream.

In wiphy_new_nm(), if an error occurs after dev_set_name() and
device_initialize() have already been called, it's necessary to call
put_device() (via wiphy_free()) to avoid a memory leak.

Reported-by: syzbot+7fddca22578bc67c3fe4@syzkaller.appspotmail.com
Fixes: 1f87f7d3a3b4 ("cfg80211: add rfkill support")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers 
Signed-off-by: Johannes Berg 
Signed-off-by: Greg Kroah-Hartman

cfg80211: limit wiphy names to 128 bytes

2018-05-26T06:49:00+00:00

commit a7cfebcb7594a24609268f91299ab85ba064bf82 upstream.

There's currently no limit on wiphy names, other than netlink
message size and memory limitations, but that causes issues when,
for example, the wiphy name is used in a uevent, e.g. in rfkill
where we use the same name for the rfkill instance, and then the
buffer there is "only" 2k for the environment variables.

This was reported by syzkaller, which used a 4k name.

Limit the name to something reasonable, I randomly picked 128.

Reported-by: syzbot+230d9e642a85d3fec29c@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg 
Signed-off-by: Greg Kroah-Hartman

cfg80211: check dev_set_name() return value

2018-02-25T10:03:35+00:00

commit 59b179b48ce2a6076448a44531242ac2b3f6cef2 upstream.

syzbot reported a warning from rfkill_alloc(), and after a while
I think that the reason is that it was doing fault injection and
the dev_set_name() failed, leaving the name NULL, and we didn't
check the return value and got to rfkill_alloc() with a NULL name.
Since we really don't want a NULL name, we ought to check the
return value.

Fixes: fb28ad35906a ("net: struct device - replace bus_id with dev_name(), dev_set_name()")
Reported-by: syzbot+1ddfb3357e1d7bb5b5d3@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg 
Signed-off-by: Greg Kroah-Hartman

cfg80211/wext: fix message ordering

2016-03-16T15:42:59+00:00

commit cb150b9d23be6ee7f3a0fff29784f1c5b5ac514d upstream.

Since cfg80211 frequently takes actions from its netdev notifier
call, wireless extensions messages could still be ordered badly
since the wext netdev notifier, since wext is built into the
kernel, runs before the cfg80211 netdev notifier. For example,
the following can happen:

5: wlan1:  mtu 1500 qdisc mq state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: 
    link/ether

when setting the interface down causes the wext message.

To also fix this, export the wireless_nlevent_flush() function
and also call it from the cfg80211 notifier.

Signed-off-by: Johannes Berg 
Signed-off-by: Greg Kroah-Hartman

cfg80211: fix gHz to GHz

2015-10-15T14:17:07+00:00

There's no "g" prefix, only "G" (1e9) that was clearly intended here.

Signed-off-by: Johannes Berg

cfg80211: Add multiple scan plans for scheduled scan

2015-10-13T08:35:26+00:00

Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.

When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.

Signed-off-by: Avraham Stern 
Signed-off-by: Luca Coelho 
Signed-off-by: Johannes Berg

net/wireless: enable wiphy device to suspend/resume asynchronously

2015-09-29T13:56:46+00:00

Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition timing dependency between devices. This
patch enables wiphy device to suspend/resume asynchronously. This can
take advantage of multicore and improve system suspend/resume speed.

Signed-off-by: Zhonghui Fu 
Signed-off-by: Johannes Berg

cfg80211: allow mgmt_frame_register callback to sleep

2015-07-17T13:38:26+00:00

This callback is currently not allowed to sleep, which makes it more
difficult to implement proper driver methods in mac80211 than it has
to be. Instead of doing asynchronous work here in mac80211, make it
possible for the callback to sleep by doing some asynchronous work
in cfg80211. This also enables improvements to other drivers, like
ath6kl, that would like to sleep in this callback.

While at it, also fix the code to call the driver on the implicit
unregistration when an interface is removed, and do that also when
a P2P-Device wdev is destroyed (otherwise we leak the structs.)

Signed-off-by: Johannes Berg

cfg80211: calls nl80211_exit on error

2015-02-24T10:41:21+00:00

nl80211_exit should be called in cfg80211_init if nl80211_init succeeds
but regulatory_init or create_singlethread_workqueue fails.

Signed-off-by: Junjie Mao 
Signed-off-by: Johannes Berg

Revert "wireless: Support of IFLA_INFO_KIND rtnl attribute"

2015-01-19T17:49:56+00:00

This reverts commit ba1debdfed974f25aa598c283567878657b292ee.

Oliver reported that it breaks network-manager, for some reason with
this patch NM decides that the device isn't wireless but "generic"
(ethernet), sees no carrier (as expected with wifi) and fails to do
anything else with it.

Revert this to unbreak userspace.

Reported-by: Oliver Hartkopp 
Tested-by: Oliver Hartkopp 
Signed-off-by: Johannes Berg