linux-stable.git/net/wireless/chan.c, branch linux-5.9.y

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2020-09-04T01:50:48+00:00

Pull networking fixes from David Miller:

 1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
    Kivilinna.

 2) Fix loss of RTT samples in rxrpc, from David Howells.

 3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.

 4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.

 5) We disable BH for too lokng in sctp_get_port_local(), add a
    cond_resched() here as well, from Xin Long.

 6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.

 7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
    Yonghong Song.

 8) Missing of_node_put() in mt7530 DSA driver, from Sumera
    Priyadarsini.

 9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.

10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.

11) Memory leak in rxkad_verify_response, from Dinghao Liu.

12) In tipc, don't use smp_processor_id() in preemptible context. From
    Tuong Lien.

13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.

14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.

15) Fix ABI mismatch between driver and firmware in nfp, from Louis
    Peens.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
  net/smc: fix sock refcounting in case of termination
  net/smc: reset sndbuf_desc if freed
  net/smc: set rx_off for SMCR explicitly
  net/smc: fix toleration of fake add_link messages
  tg3: Fix soft lockup when tg3_reset_task() fails.
  doc: net: dsa: Fix typo in config code sample
  net: dp83867: Fix WoL SecureOn password
  nfp: flower: fix ABI mismatch between driver and firmware
  tipc: fix shutdown() of connectionless socket
  ipv6: Fix sysctl max for fib_multipath_hash_policy
  drivers/net/wan/hdlc: Change the default of hard_header_len to 0
  net: gemini: Fix another missing clk_disable_unprepare() in probe
  net: bcmgenet: fix mask check in bcmgenet_validate_flow()
  amd-xgbe: Add support for new port mode
  net: usb: dm9601: Add USB ID of Keenetic Plus DSL
  vhost: fix typo in error message
  net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
  pktgen: fix error message with wrong function name
  net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
  cxgb4: fix thermal zone device registration
  ...

wireless: fix wrong 160/80+80 MHz setting

2020-08-27T08:46:53+00:00

Fix cfg80211_chandef_usable():
consider IEEE80211_VHT_CAP_EXT_NSS_BW when verifying 160/80+80 MHz.

Based on:
"Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW
Support subfield at a STA transmitting the VHT Capabilities Information field"
From "Draft P802.11REVmd_D3.0.pdf"

Signed-off-by: Aviad Brikman 
Signed-off-by: Shay Bar 
Link: https://lore.kernel.org/r/20200826143139.25976-1-shay.bar@celeno.com
[reformat the code a bit and use u32_get_bits()]
Signed-off-by: Johannes Berg

treewide: Use fallthrough pseudo-keyword

2020-08-23T22:36:59+00:00

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva

nl80211: S1G band and channel definitions

2020-07-31T07:24:13+00:00

Gives drivers the definitions needed to advertise support
for S1G bands.

Signed-off-by: Thomas Pedersen 
Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com
Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg

cfg80211: treat 6 GHz channels as valid regardless of capability

2020-05-31T09:27:08+00:00

If a 6 GHz channel exists, then we can probably safely assume that
the device actually supports it, and then it should support most
bandwidths.

This will probably need to be extended to check the interface type
and then dig into the HE capabilities for that though, to have the
correct bandwidth check.

Link: https://lore.kernel.org/r/20200528213443.d4864ef52e92.I82f09b2b14a56413ce20376d09967fe954a033eb@changeid
Signed-off-by: Johannes Berg

cfg80211: reject channels/chandefs with KHz offset >= 1000

2020-04-24T10:38:20+00:00

This should be covered by the next MHz, make sure that the
numbers are always normalized.

Signed-off-by: Johannes Berg 
Link: https://lore.kernel.org/r/20200424120103.12b91ecf75f9.I4bf499d58404283bbfacb517d614a816763bccf2@changeid
Signed-off-by: Johannes Berg

cfg80211: express channels with a KHz component

2020-04-24T10:33:43+00:00

Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:

MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;

Also provide some helper functions to do the frequency
conversion and test for equality.

Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.

Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.

mesh, ibss, wext, etc. are currently ignored.

Signed-off-by: Thomas Pedersen 
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg

nl80211: Disallow setting of HT for channel 14

2019-10-30T09:07:22+00:00

This patch disables setting of HT20 and more for channel 14 because
the channel is only for IEEE 802.11b.

The patch for net/wireless/util.c was unit-tested.

The patch for net/wireless/chan.c was tested with iw command.

Before this patch.
$ sudo iw dev  set channel 14 HT20
$

After this patch.
$ sudo iw dev  set channel 14 HT20
kernel reports: invalid channel definition
command failed: Invalid argument (-22)
$

Signed-off-by: Masashi Honma 
Link: https://lore.kernel.org/r/20191021075045.2719-1-masashi.honma@gmail.com
[clean up the code, use != instead of equivalent >]
Signed-off-by: Johannes Berg

nl80211: Add support for EDMG channels

2019-08-21T09:07:35+00:00

802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.

Introduce new NL attributes that are needed for enabling and
configuring EDMG support.

Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.

Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG

New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.

Signed-off-by: Alexei Avshalom Lazar 
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg

cfg80211: use same IR permissive rules for 6GHz band

2019-08-21T08:54:35+00:00

The function cfg80211_ir_permissive_chan() is applicable for
6GHz band as well so make sure it is handled.

Reviewed-by: Pieter-Paul Giesberts 
Reviewed-by: Leon Zegers 
Signed-off-by: Arend van Spriel 
Link: https://lore.kernel.org/r/1564745465-21234-7-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg