linux-stable.git/net/tipc/discover.c, branch linux-3.3.y

tipc: rename struct link* to struct tipc_link*

2011-12-30T02:53:30+00:00

This converts the following:

	struct link		->	struct tipc_link
	struct link_req		->	struct tipc_link_req
	struct link_name	->	struct tipc_link_name

Signed-off-by: Paul Gortmaker

tipc: Ignore neighbor discovery messages containing invalid address

2011-12-27T16:33:38+00:00

Adds a check to ensure that TIPC ignores an incoming neighbor discovery
message that specifies an invalid media address as its source. The check
ensures that the source address is a valid, non-broadcast address that
could legally be used by a neighboring link endpoint.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker

tipc: Hide media-specific addressing details from generic bearer code

2011-12-27T16:33:36+00:00

Reworks TIPC's media address data structure and associated processing
routines to transfer all media-specific details of address conversion
to the associated TIPC media adaptation code. TIPC's generic bearer code
now only needs to know which media type an address is associated with
and whether or not it is a broadcast address, and totally ignores the
"value" field that contains the actual media-specific addressing info.

These changes eliminate the need for a number of endianness conversion
operations and will make it easier for TIPC to support new media types
in the future.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker

tipc: Ensure both nodes recognize loss of contact between them

2011-09-18T02:55:03+00:00

Enhances TIPC to ensure that a node that loses contact with a
neighboring node does not allow contact to be re-established until
it sees that its peer has also recognized the loss of contact.

Previously, nodes that were connected by two or more links could
encounter a situation in which node A would lose contact with node B
on all of its links, purge its name table of names published by B,
and then fail to repopulate those names once contact with B was restored.
This would happen because B was able to re-establish one or more links
so quickly that it never reached a point where it had no links to A --
meaning that B never saw a loss of contact with A, and consequently
didn't re-publish its names to A.

This problem is now prevented by enhancing the cleanup done by TIPC
following a loss of contact with a neighboring node to ensure that
node A ignores all messages sent by B until it receives a LINK_PROTOCOL
message that indicates B has lost contact with A, thereby preventing
the (re)establishment of links between the nodes. The loss of contact
is recognized when a RESET or ACTIVATE message is received that has
a "redundant link exists" field of 0, indicating that B's sending link
endpoint is in a reset state and that B has no other working links.

Additionally, TIPC now suppresses the sending of (most) link protocol
messages to a neighboring node while it is cleaning up after an earlier
loss of contact with that node. This stops the peer node from prematurely
activating its link endpoint, which would prevent TIPC from later
activating its own end. TIPC still allows outgoing RESET messages to
occur during cleanup, to avoid problems if its own node recognizes
the loss of contact first and tries to notify the peer of the situation.

Finally, TIPC now recognizes an impending loss of contact with a peer node
as soon as it receives a RESET message on a working link that is the
peer's only link to the node, and ensures that the link protocol
suppression mentioned above goes into effect right away -- that is,
even before its own link endpoints have failed. This is necessary to
ensure correct operation when there are redundant links between the nodes,
since otherwise TIPC would send an ACTIVATE message upon receiving a RESET
on its first link and only begin suppressing when a RESET on its second
link was received, instead of initiating suppression with the first RESET
message as it needs to.

Note: The reworked cleanup code also eliminates a check that prevented
a link endpoint's discovery object from responding to incoming messages
while stale name table entries are being purged. This check is now
unnecessary and would have slowed down re-establishment of communication
between the nodes in some situations.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker

tipc: Revise timings used when sending link request messages

2011-05-10T20:04:02+00:00

Revises the algorithm governing the sending of link request messages
to take into account the number of nodes each bearer is currently in
contact with, and to ensure more rapid rediscovery of neighboring nodes
if a bearer fails and then recovers.

The discovery object now sends requests at least once a second if it
is not in contact with any other nodes, and at least once a minute if
it has at least one neighbor; if contact with the only neighbor is
lost, the object immediately reverts to its initial rapid-fire search
timing to accelerate the rediscovery process.

In addition, the discovery object now stops issuing link request
messages if it is in contact with the only neighboring node it is
configured to communicate with, since further searching is unnecessary.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker

tipc: Add monitoring of number of nodes discovered by bearer

2011-05-10T20:04:01+00:00

Augments TIPC's discovery object to track the number of neighboring nodes
having an active link to the associated bearer.

This means tipc_disc_update_link_req() becomes either one of:

       tipc_disc_add_dest()
or:
       tipc_disc_remove_dest()

depending on the code flow direction of things.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker

tipc: Enhance sending of discovery object link request messages

2011-05-10T20:04:00+00:00

Augments TIPC's discovery object to send its initial neighbor discovery
request message as soon as the associated bearer is created, rather than
waiting for its first periodic timeout to occur, thereby speeding up the
discovery process. Also adds a check to suppress the initial request or
subsequent requests if the bearer is blocked at the time the request is
scheduled for transmission.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker

tipc: Enhance handling of discovery object creation failures

2011-05-10T20:03:59+00:00

Modifies bearer creation and deletion code to improve handling of
scenarios when a neighbor discovery object cannot be created. The
creation routine now aborts the creation of a bearer if its discovery
object cannot be created, and deletes the newly created bearer, rather
than failing quietly and leaving an unusable bearer hanging around.

Since the exit via the goto label really isn't a definitive failure
in all cases, relabel it appropriately.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker

tipc: Strengthen checks for neighboring node discovery

2011-05-10T20:03:55+00:00

Enhances existing checks on the discovery domain associated with a TIPC
bearer. A bearer can no longer be configured to accept links from itself
only (which would be pointless), or to nodes outside its own cluster
(since multi-cluster support has now been removed from TIPC). Also, the
neighbor discovery routine now validates link setup requests against the
configured discovery domain for the bearer, rather than simply ensuring
the requesting node belongs to the node's own cluster.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker

tipc: Don't respond to neighbor discovery request on blocked bearer

2011-03-13T20:35:19+00:00

Adds a check to prevent TIPC from trying to respond to an incoming
LINK_CONFIG request message if the associated bearer is currently
prohibited from sending messages.

Signed-off-by: Allan Stephens 
Signed-off-by: Paul Gortmaker