linux-stable.git/net/sctp/protocol.c, branch linux-4.0.y

Merge branch 'for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu

2014-10-10T11:26:02+00:00

Pull percpu updates from Tejun Heo:
 "A lot of activities on percpu front.  Notable changes are...

   - percpu allocator now can take @gfp.  If @gfp doesn't contain
     GFP_KERNEL, it tries to allocate from what's already available to
     the allocator and a work item tries to keep the reserve around
     certain level so that these atomic allocations usually succeed.

     This will replace the ad-hoc percpu memory pool used by
     blk-throttle and also be used by the planned blkcg support for
     writeback IOs.

     Please note that I noticed a bug in how @gfp is interpreted while
     preparing this pull request and applied the fix 6ae833c7fe0c
     ("percpu: fix how @gfp is interpreted by the percpu allocator")
     just now.

   - percpu_ref now uses longs for percpu and global counters instead of
     ints.  It leads to more sparse packing of the percpu counters on
     64bit machines but the overhead should be negligible and this
     allows using percpu_ref for refcnting pages and in-memory objects
     directly.

   - The switching between percpu and single counter modes of a
     percpu_ref is made independent of putting the base ref and a
     percpu_ref can now optionally be initialized in single or killed
     mode.  This allows avoiding percpu shutdown latency for cases where
     the refcounted objects may be synchronously created and destroyed
     in rapid succession with only a fraction of them reaching fully
     operational status (SCSI probing does this when combined with
     blk-mq support).  It's also planned to be used to implement forced
     single mode to detect underflow more timely for debugging.

  There's a separate branch percpu/for-3.18-consistent-ops which cleans
  up the duplicate percpu accessors.  That branch causes a number of
  conflicts with s390 and other trees.  I'll send a separate pull
  request w/ resolutions once other branches are merged"

* 'for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (33 commits)
  percpu: fix how @gfp is interpreted by the percpu allocator
  blk-mq, percpu_ref: start q->mq_usage_counter in atomic mode
  percpu_ref: make INIT_ATOMIC and switch_to_atomic() sticky
  percpu_ref: add PERCPU_REF_INIT_* flags
  percpu_ref: decouple switching to percpu mode and reinit
  percpu_ref: decouple switching to atomic mode and killing
  percpu_ref: add PCPU_REF_DEAD
  percpu_ref: rename things to prepare for decoupling percpu/atomic mode switch
  percpu_ref: replace pcpu_ prefix with percpu_
  percpu_ref: minor code and comment updates
  percpu_ref: relocate percpu_ref_reinit()
  Revert "blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe"
  Revert "percpu: free percpu allocation info for uniprocessor system"
  percpu-refcount: make percpu_ref based on longs instead of ints
  percpu-refcount: improve WARN messages
  percpu: fix locking regression in the failure path of pcpu_alloc()
  percpu-refcount: add @gfp to percpu_ref_init()
  proportions: add @gfp to init functions
  percpu_counter: add @gfp to percpu_counter_init()
  percpu_counter: make percpu_counters_lock irq-safe
  ...

net/ipv4: bind ip_nonlocal_bind to current netns

2014-09-09T18:27:09+00:00

net.ipv4.ip_nonlocal_bind sysctl was global to all network
namespaces. This patch allows to set a different value for each
network namespace.

Signed-off-by: Vincent Bernat 
Signed-off-by: David S. Miller

percpu_counter: add @gfp to percpu_counter_init()

2014-09-08T00:51:29+00:00

Percpu allocator now supports allocation mask.  Add @gfp to
percpu_counter_init() so that !GFP_KERNEL allocation masks can be used
with percpu_counters too.

We could have left percpu_counter_init() alone and added
percpu_counter_init_gfp(); however, the number of users isn't that
high and introducing _gfp variants to all percpu data structures would
be quite ugly, so let's just do the conversion.  This is the one with
the most users.  Other percpu data structures are a lot easier to
convert.

This patch doesn't make any functional difference.

Signed-off-by: Tejun Heo 
Acked-by: Jan Kara 
Acked-by: "David S. Miller" 
Cc: x86@kernel.org
Cc: Jens Axboe 
Cc: "Theodore Ts'o" 
Cc: Alexander Viro 
Cc: Andrew Morton

sctp: Fixup v4mapped behaviour to comply with Sock API

2014-08-01T04:49:06+00:00

The SCTP socket extensions API document describes the v4mapping option as
follows:

8.1.15.  Set/Clear IPv4 Mapped Addresses (SCTP_I_WANT_MAPPED_V4_ADDR)

   This socket option is a Boolean flag which turns on or off the
   mapping of IPv4 addresses.  If this option is turned on, then IPv4
   addresses will be mapped to V6 representation.  If this option is
   turned off, then no mapping will be done of V4 addresses and a user
   will receive both PF_INET6 and PF_INET type addresses on the socket.
   See [RFC3542] for more details on mapped V6 addresses.

This description isn't really in line with what the code does though.

Introduce addr_to_user (renamed addr_v4map), which should be called
before any sockaddr is passed back to user space. The new function
places the sockaddr into the correct format depending on the
SCTP_I_WANT_MAPPED_V4_ADDR option.

Audit all places that touched v4mapped and either sanely construct
a v4 or v6 address then call addr_to_user, or drop the
unnecessary v4mapped check entirely.

Audit all places that call addr_to_user and verify they are on a sycall
return path.

Add a custom getname that formats the address properly.

Several bugs are addressed:
 - SCTP_I_WANT_MAPPED_V4_ADDR=0 often returned garbage for
   addresses to user space
 - The addr_len returned from recvmsg was not correct when
   returning AF_INET on a v6 socket
 - flowlabel and scope_id were not zerod when promoting
   a v4 to v6
 - Some syscalls like bind and connect behaved differently
   depending on v4mapped

Tested bind, getpeername, getsockname, connect, and recvmsg for proper
behaviour in v4mapped = 1 and 0 cases.

Signed-off-by: Neil Horman 
Tested-by: Jason Gunthorpe 
Signed-off-by: Jason Gunthorpe 
Signed-off-by: David S. Miller

net: Eliminate no_check from protosw

2014-05-23T20:28:53+00:00

It doesn't seem like an protocols are setting anything other
than the default, and allowing to arbitrarily disable checksums
for a whole protocol seems dangerous. This can be done on a per
socket basis.

Signed-off-by: Tom Herbert 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2014-05-12T17:19:14+00:00

Conflicts:
	drivers/net/ethernet/altera/altera_sgdma.c
	net/netlink/af_netlink.c
	net/sched/cls_api.c
	net/sched/sch_api.c

The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces.  These were simple transformations from
netlink_capable to netlink_ns_capable.

The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.

Signed-off-by: David S. Miller

net: clean up snmp stats code

2014-05-07T20:06:05+00:00

commit 8f0ea0fe3a036a47767f9c80e (snmp: reduce percpu needs by 50%)
reduced snmp array size to 1, so technically it doesn't have to be
an array any more. What's more, after the following commit:

	commit 933393f58fef9963eac61db8093689544e29a600
	Date:   Thu Dec 22 11:58:51 2011 -0600

	    percpu: Remove irqsafe_cpu_xxx variants

	    We simply say that regular this_cpu use must be safe regardless of
	    preemption and interrupt state.  That has no material change for x86
	    and s390 implementations of this_cpu operations.  However, arches that
	    do not provide their own implementation for this_cpu operations will
	    now get code generated that disables interrupts instead of preemption.

probably no arch wants to have SNMP_ARRAY_SZ == 2. At least after
almost 3 years, no one complains.

So, just convert the array to a single pointer and remove snmp_mib_init()
and snmp_mib_free() as well.

Cc: Christoph Lameter 
Cc: Eric Dumazet 
Cc: David S. Miller 
Signed-off-by: Cong Wang 
Signed-off-by: David S. Miller

sctp: reset flowi4_oif parameter on route lookup

2014-04-27T23:46:17+00:00

commit 813b3b5db83 (ipv4: Use caller's on-stack flowi as-is
in output route lookups.) introduces another regression which
is very similar to the problem of commit e6b45241c (ipv4: reset
flowi parameters on route connect) wants to fix:
Before we call ip_route_output_key() in sctp_v4_get_dst() to
get a dst that matches a bind address as the source address,
we have already called this function previously and the flowi
parameters have been initialized including flowi4_oif, so when
we call this function again, the process in __ip_route_output_key()
will be different because of the setting of flowi4_oif, and we'll
get a networking device which corresponds to the inputted flowi4_oif
as the output device, this is wrong because we'll never hit this
place if the previously returned source address of dst match one
of the bound addresses.

To reproduce this problem, a vlan setting is enough:
  # ifconfig eth0 up
  # route del default
  # vconfig add eth0 2
  # vconfig add eth0 3
  # ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0
  # route add default gw 10.0.1.254 dev eth0.2
  # ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0
  # ip rule add from 10.0.0.14 table 4
  # ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3
  # sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I
You'll detect that all the flow are routed to eth0.2(10.0.1.254).

Signed-off-by: Xufeng Zhang 
Signed-off-by: Julian Anastasov 
Acked-by: Vlad Yasevich 
Signed-off-by: David S. Miller

ipv4: add a sock pointer to ip_queue_xmit()

2014-04-15T16:58:34+00:00

ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d5956fc ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.

One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.

Fixes: 31c70d5956fc ("l2tp: keep original skb ownership")
Reported-by: Zhan Jianyu 
Tested-by: Zhan Jianyu 
Signed-off-by: Eric Dumazet 
Signed-off-by: David S. Miller

sctp: remove macros sctp_bh_[un]lock_sock

2014-01-22T02:41:36+00:00

Redefined bh_[un]lock_sock to sctp_bh[un]lock_sock for user
space friendly code which we haven't use in years, so removing them.

Signed-off-by: Wang Weidong 
Signed-off-by: David S. Miller