If a frame's timestamp is calculated, and the bitrate
calculation goes wrong and returns zero, the system
will attempt to divide by zero and crash. Catch this
case and print the rate information that the driver
reported when this happens.

Cc: stable@vger.kernel.org
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

__ieee80211_scan_completed is called from a worker. This
means that the following flow is possible.

 * driver calls ieee80211_scan_completed
 * mac80211 cancels the scan (that is already complete)
 * __ieee80211_scan_completed runs

When scan_work will finally run, it will see that the scan
hasn't been aborted and might even trigger another scan on
another band. This leads to a situation where cfg80211's
scan is not done and no further scan can be issued.

Fix this by setting a new flag when a HW scan is being
cancelled so that no other scan will be triggered.

Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211 scan processing could get stuck if roc work for pending, but
not started when a scan request was deferred due to such roc item.
Normally the deferred scan would be started from
ieee80211_start_next_roc(), but ieee80211_sw_roc_work() calls that only
if the finished ROC was started. Fix this by calling
ieee80211_run_deferred_scan() in the case the last ROC was not actually
started.

This issue was hit relatively easily in P2P find operations where Listen
state (remain-on-channel) and Search state (scan) are repeated in a
loop.

Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When clients are idle for too long, hostapd sends nullfunc frames for
probing. When those are acked by the client, the idle time needs to be
updated.

To make this work (and to avoid unnecessary probing), update sta->last_rx
whenever an ACK was received for a tx packet. Only do this if the flag
IEEE80211_HW_REPORTS_TX_ACK_STATUS is set.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This allows calls for clients in AP_VLANs (e.g. for 4-addr) to succeed

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The patch "mac80211: select and adjust bitrates according to
channel mode" causes regression and breaks the extended supported rate
IE setting. Since "i" is starting with 8, so this is not necessary
to introduce "skip" here.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Reviewed-by: Jason Abele <jason@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If an Ad-Hoc node receives packets with the Cell ID or its own MAC
address as source address, it hits a WARN_ON in sta_info_insert_check()
With many packets, this can massively spam the logs. One way that this
can easily happen is through having Cisco APs in the area with rouge AP
detection and countermeasures enabled.
Such Cisco APs will regularly send fake beacons, disassoc and deauth
packets that trigger these warnings.

To fix this issue, drop such spoofed packets early in the rx path.

Cc: stable@vger.kernel.org
Reported-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Conflicts:
	drivers/net/wireless/iwlwifi/pcie/trans.c
	net/mac80211/ibss.c