linux-stable.git/net/mac80211/debugfs_netdev.c, branch linux-5.0.y

mac80211: don't attempt to rename ERR_PTR() debugfs dirs

2019-05-08T05:22:43+00:00

commit 517879147493a5e1df6b89a50f708f1133fcaddb upstream.

We need to dereference the directory to get its parent to
be able to rename it, so it's clearly not safe to try to
do this with ERR_PTR() pointers. Skip in this case.

It seems that this is most likely what was causing the
report by syzbot, but I'm not entirely sure as it didn't
come with a reproducer this time.

Cc: stable@vger.kernel.org
Reported-by: syzbot+4ece1a28b8f4730547c9@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg 
Signed-off-by: Greg Kroah-Hartman

{nl,mac}80211: add dot11MeshConnectedToMeshGate to meshconf

2018-11-09T10:39:44+00:00

When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table.  Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.

Signed-off-by: Bob Copeland 
Signed-off-by: Johannes Berg

networking: convert many more places to skb_put_zero()

2017-06-16T15:48:35+00:00

There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.

The following spatch found many more and also removes the
now unnecessary casts:

    @@
    identifier p, p2;
    expression len;
    expression skb;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_zero(skb, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_zero(skb, len);
    )
    ... when != p
    (
    p2 = (t2)p;
    -memset(p2, 0, len);
    |
    -memset(p, 0, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_zero(skb, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_zero(skb, sizeof(t));
    )
    ... when != p
    (
    p2 = (t2)p;
    -memset(p2, 0, sizeof(*p));
    |
    -memset(p, 0, sizeof(*p));
    )

    @@
    expression skb, len;
    @@
    -memset(skb_put(skb, len), 0, len);
    +skb_put_zero(skb, len);

Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)

Signed-off-by: Johannes Berg 
Signed-off-by: David S. Miller

mac80211: multicast to unicast conversion

2016-12-13T15:05:11+00:00

Add the ability for an AP (and associated VLANs) to perform
multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own
MAC address rather than the group address.

Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)

This also doesn't implement the 802.11 DMS (directed multicast
service).

Signed-off-by: Michael Braun 
[use true/false, rename label to the correct "multicast",
 use __be16 for ethertype and network order for constants]
Signed-off-by: Johannes Berg

mac80211: filter multicast data packets on AP / AP_VLAN

2016-10-12T09:33:29+00:00

This patch adds filtering for multicast data packets on AP_VLAN
interfaces that have no authorized station connected and changes
filtering on AP interfaces to not count stations assigned to
AP_VLAN interfaces.

This saves airtime and avoids waking up other stations currently
authorized in this BSS. When using WPA, the packets dropped could
not be decrypted by any station.

The behaviour when there are no AP_VLAN interfaces is left unchanged.

When there are AP_VLAN interfaces, this patch
1. adds filtering multicast data packets sent on AP_VLAN interfaces
   that have no authorized station connected.
   No filtering happens on 4addr AP_VLAN interfaces.
2. makes filtering of multicast data packets sent on AP interfaces
   depend on the number of authorized stations in this bss not
   assigned to an AP_VLAN interface.

Therefore, a new num_mcast_sta counter is added for AP_VLAN interfaces.
The existing one for AP interfaces is altered to not track stations
assigned to an AP_VLAN interface.

The new counter is exposed in debugfs.

Signed-off-by: Michael Braun 
[reformat commit message a bit, unline ieee80211_vif_{inc,dec}_num_mcast]
Signed-off-by: Johannes Berg

mac80211: add offset_tsf driver op and use it for mesh

2016-09-30T11:45:44+00:00

This allows the mesh sync (and debugfs) code to make incremental
TSF adjustments, avoiding any uncertainty introduced by delay in
programming absolute TSF.

Signed-off-by: Thomas Pedersen 
Signed-off-by: Johannes Berg

mac80211: Re-structure aqm debugfs output and keep CoDel stats per txq

2016-09-13T06:20:16+00:00

Currently the 'aqm' stats in mac80211 only keeps overlimit drop stats,
not CoDel stats. This moves the CoDel stats into the txqi structure to
keep them per txq in order to show them in debugfs.

In addition, the aqm debugfs output is restructured by splitting it up
into three files: One global per phy, one per netdev and one per
station, in the appropriate directories. The files are all called aqm,
and are only created if the driver supports the wake_tx_queue op (rather
than emitting an error on open as previously).

Signed-off-by: Toke Høiland-Jørgensen 
Signed-off-by: Johannes Berg

cfg80211: remove enum ieee80211_band

2016-04-12T13:56:15+00:00

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.

Signed-off-by: Johannes Berg

mac80211: remove last_beacon/ave_beacon debugfs files

2015-09-22T13:21:25+00:00

These file aren't really useful:
 - if per beacon data is required then you need to use
   radiotap or similar anyway, debugfs won't help much
 - average beacon signal is reported in station info in
   nl80211 and can be looked up with iw

Signed-off-by: Johannes Berg

mac80211: debugfs: add file to disallow TDLS wider-bw

2015-09-22T13:21:21+00:00

Sometimes we are interested in testing TDLS performance in a specific
width setting. Add the ability to disable the wider-band feature, thereby
allowing the TDLS channel width to be controlled by the BSS width.

Signed-off-by: Arik Nemtsov 
Signed-off-by: Emmanuel Grumbach 
Signed-off-by: Johannes Berg