linux-stable.git/net/ipv4, branch v5.4.97

net: ip_tunnel: fix mtu calculation

2021-02-10T08:25:32+00:00

commit 28e104d00281ade30250b24e098bf50887671ea4 upstream.

dev->hard_header_len for tunnel interface is set only when header_ops
are set too and already contains full overhead of any tunnel encapsulation.
That's why there is not need to use this overhead twice in mtu calc.

Fixes: fdafed459998 ("ip_gre: set dev->hard_header_len and dev->needed_headroom properly")
Reported-by: Slava Bacherikov 
Signed-off-by: Vadim Fedorenko 
Link: https://lore.kernel.org/r/1611959267-20536-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

tcp: make TCP_USER_TIMEOUT accurate for zero window probes

2021-02-07T14:35:47+00:00

commit 344db93ae3ee69fc137bd6ed89a8ff1bf5b0db08 upstream.

The TCP_USER_TIMEOUT is checked by the 0-window probe timer. As the
timer has backoff with a max interval of about two minutes, the
actual timeout for TCP_USER_TIMEOUT can be off by up to two minutes.

In this patch the TCP_USER_TIMEOUT is made more accurate by taking it
into account when computing the timer value for the 0-window probes.

This patch is similar to and builds on top of the one that made
TCP_USER_TIMEOUT accurate for RTOs in commit b701a99e431d ("tcp: Add
tcp_clamp_rto_to_user_timeout() helper to improve accuracy").

Fixes: 9721e709fa68 ("tcp: simplify window probe aborting on USER_TIMEOUT")
Signed-off-by: Enke Chen 
Reviewed-by: Neal Cardwell 
Signed-off-by: Eric Dumazet 
Link: https://lore.kernel.org/r/20210122191306.GA99540@localhost.localdomain
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

tcp: fix TLP timer not set when CA_STATE changes from DISORDER to OPEN

2021-02-03T22:26:02+00:00

commit 62d9f1a6945ba69c125e548e72a36d203b30596e upstream.

Upon receiving a cumulative ACK that changes the congestion state from
Disorder to Open, the TLP timer is not set. If the sender is app-limited,
it can only wait for the RTO timer to expire and retransmit.

The reason for this is that the TLP timer is set before the congestion
state changes in tcp_ack(), so we delay the time point of calling
tcp_set_xmit_timer() until after tcp_fastretrans_alert() returns and
remove the FLAG_SET_XMIT_TIMER from ack_flag when the RACK reorder timer
is set.

This commit has two additional benefits:
1) Make sure to reset RTO according to RFC6298 when receiving ACK, to
avoid spurious RTO caused by RTO timer early expires.
2) Reduce the xmit timer reschedule once per ACK when the RACK reorder
timer is set.

Fixes: df92c8394e6e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Link: https://lore.kernel.org/netdev/1611311242-6675-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Pengcheng Yang 
Acked-by: Neal Cardwell 
Acked-by: Yuchung Cheng 
Cc: Eric Dumazet 
Link: https://lore.kernel.org/r/1611464834-23030-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

tcp: fix TCP_USER_TIMEOUT with zero window

2021-01-27T10:47:55+00:00

commit 9d9b1ee0b2d1c9e02b2338c4a4b0a062d2d3edac upstream.

The TCP session does not terminate with TCP_USER_TIMEOUT when data
remain untransmitted due to zero window.

The number of unanswered zero-window probes (tcp_probes_out) is
reset to zero with incoming acks irrespective of the window size,
as described in tcp_probe_timer():

    RFC 1122 4.2.2.17 requires the sender to stay open indefinitely
    as long as the receiver continues to respond probes. We support
    this by default and reset icsk_probes_out with incoming ACKs.

This counter, however, is the wrong one to be used in calculating the
duration that the window remains closed and data remain untransmitted.
Thanks to Jonathan Maxwell  for diagnosing the
actual issue.

In this patch a new timestamp is introduced for the socket in order to
track the elapsed time for the zero-window probes that have not been
answered with any non-zero window ack.

Fixes: 9721e709fa68 ("tcp: simplify window probe aborting on USER_TIMEOUT")
Reported-by: William McCall 
Co-developed-by: Neal Cardwell 
Signed-off-by: Neal Cardwell 
Signed-off-by: Enke Chen 
Reviewed-by: Yuchung Cheng 
Reviewed-by: Eric Dumazet 
Link: https://lore.kernel.org/r/20210115223058.GA39267@localhost.localdomain
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

tcp: do not mess with cloned skbs in tcp_add_backlog()

2021-01-27T10:47:55+00:00

commit b160c28548bc0a87cbd16d5af6d3edcfd70b8c9a upstream.

Heiner Kallweit reported that some skbs were sent with
the following invalid GSO properties :
- gso_size > 0
- gso_type == 0

This was triggerring a WARN_ON_ONCE() in rtl8169_tso_csum_v2.

Juerg Haefliger was able to reproduce a similar issue using
a lan78xx NIC and a workload mixing TCP incoming traffic
and forwarded packets.

The problem is that tcp_add_backlog() is writing
over gso_segs and gso_size even if the incoming packet will not
be coalesced to the backlog tail packet.

While skb_try_coalesce() would bail out if tail packet is cloned,
this overwriting would lead to corruptions of other packets
cooked by lan78xx, sharing a common super-packet.

The strategy used by lan78xx is to use a big skb, and split
it into all received packets using skb_clone() to avoid copies.
The drawback of this strategy is that all the small skb share a common
struct skb_shared_info.

This patch rewrites TCP gso_size/gso_segs handling to only
happen on the tail skb, since skb_try_coalesce() made sure
it was not cloned.

Fixes: 4f693b55c3d2 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet 
Bisected-by: Juerg Haefliger 
Tested-by: Juerg Haefliger 
Reported-by: Heiner Kallweit 
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209423
Link: https://lore.kernel.org/r/20210119164900.766957-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

udp: mask TOS bits in udp_v4_early_demux()

2021-01-27T10:47:53+00:00

commit 8d2b51b008c25240914984208b2ced57d1dd25a5 upstream.

udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.

This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).

ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.

Reproducer:

  Setup two netns, connected with veth:
  $ ip netns add ns0
  $ ip netns add ns1
  $ ip -netns ns0 link set dev lo up
  $ ip -netns ns1 link set dev lo up
  $ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
  $ ip -netns ns0 link set dev veth01 up
  $ ip -netns ns1 link set dev veth10 up
  $ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
  $ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10

  In ns0, add route to multicast address 224.0.2.0/24 using source
  address 198.51.100.10:
  $ ip -netns ns0 address add 198.51.100.10/32 dev lo
  $ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10

  In ns1, define route to 198.51.100.10, only for packets with TOS 4:
  $ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10

  Also activate rp_filter in ns1, so that incoming packets not matching
  the above route get dropped:
  $ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1

  Now try to receive packets on 224.0.2.11:
  $ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -

  In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
  tos 6 for socat):
  $ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6

  The "test0" message is properly received by socat in ns1, because
  early-demux has no cached dst to use, so source address validation
  is done by ip_route_input_mc(), which receives a TOS that has the
  ECN bits masked.

  Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
  $ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6

  The "test1" message isn't received by socat in ns1, because, now,
  early-demux has a cached dst to use and calls ip_mc_validate_source()
  immediately, without masking the ECN bits.

Fixes: bc044e8db796 ("udp: perform source validation for mcast early demux")
Signed-off-by: Guillaume Nault 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

netfilter: rpfilter: mask ecn bits before fib lookup

2021-01-27T10:47:52+00:00

commit 2e5a6266fbb11ae93c468dfecab169aca9c27b43 upstream.

RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.

Reproducer:

  Create two netns, connected with a veth:
  $ ip netns add ns0
  $ ip netns add ns1
  $ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
  $ ip -netns ns0 link set dev veth01 up
  $ ip -netns ns1 link set dev veth10 up
  $ ip -netns ns0 address add 192.0.2.10/32 dev veth01
  $ ip -netns ns1 address add 192.0.2.11/32 dev veth10

  Add a route to ns1 in ns0:
  $ ip -netns ns0 route add 192.0.2.11/32 dev veth01

  In ns1, only packets with TOS 4 can be routed to ns0:
  $ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10

  Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
  is 4:
  $ ip netns exec ns0 ping -Q 4 192.0.2.11   # TOS 4, Not-ECT
    ... 0% packet loss ...
  $ ip netns exec ns0 ping -Q 5 192.0.2.11   # TOS 4, ECT(1)
    ... 0% packet loss ...
  $ ip netns exec ns0 ping -Q 6 192.0.2.11   # TOS 4, ECT(0)
    ... 0% packet loss ...
  $ ip netns exec ns0 ping -Q 7 192.0.2.11   # TOS 4, CE
    ... 0% packet loss ...

  Now use iptable's rpfilter module in ns1:
  $ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP

  Not-ECT and ECT(1) packets still pass:
  $ ip netns exec ns0 ping -Q 4 192.0.2.11   # TOS 4, Not-ECT
    ... 0% packet loss ...
  $ ip netns exec ns0 ping -Q 5 192.0.2.11   # TOS 4, ECT(1)
    ... 0% packet loss ...

  But ECT(0) and ECN packets are dropped:
  $ ip netns exec ns0 ping -Q 6 192.0.2.11   # TOS 4, ECT(0)
    ... 100% packet loss ...
  $ ip netns exec ns0 ping -Q 7 192.0.2.11   # TOS 4, CE
    ... 100% packet loss ...

After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.

Fixes: 8f97339d3feb ("netfilter: add ipv4 reverse path filter match")
Signed-off-by: Guillaume Nault 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

esp: avoid unneeded kmap_atomic call

2021-01-23T14:57:58+00:00

[ Upstream commit 9bd6b629c39e3fa9e14243a6d8820492be1a5b2e ]

esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for
the esp trailer.

It accesses the page with kmap_atomic to handle highmem. But
skb_page_frag_refill can return compound pages, of which
kmap_atomic only maps the first underlying page.

skb_page_frag_refill does not return highmem, because flag
__GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP.
That also does not call kmap_atomic, but directly uses page_address,
in skb_copy_to_page_nocache. Do the same for ESP.

This issue has become easier to trigger with recent kmap local
debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP.

Fixes: cac2661c53f3 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a27 ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Willem de Bruijn 
Acked-by: Steffen Klassert 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

nexthop: Unlink nexthop group entry in error path

2021-01-17T13:05:32+00:00

[ Upstream commit 7b01e53eee6dce7a8a6736e06b99b68cd0cc7a27 ]

In case of error, remove the nexthop group entry from the list to which
it was previously added.

Fixes: 430a049190de ("nexthop: Add support for nexthop groups")
Signed-off-by: Ido Schimmel 
Reviewed-by: Petr Machata 
Reviewed-by: David Ahern 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

nexthop: Fix off-by-one error in error path

2021-01-17T13:05:32+00:00

[ Upstream commit 07e61a979ca4dddb3661f59328b3cd109f6b0070 ]

A reference was not taken for the current nexthop entry, so do not try
to put it in the error path.

Fixes: 430a049190de ("nexthop: Add support for nexthop groups")
Signed-off-by: Ido Schimmel 
Reviewed-by: Petr Machata 
Reviewed-by: David Ahern 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman