linux-stable.git/net/ipv4/route.c, branch linux-3.12.y

ipv4: mask tos for input route

2017-03-28T13:49:20+00:00

[ Upstream commit 6e28099d38c0e50d62c1afc054e37e573adf3d21 ]

Restore the lost masking of TOS in input route code to
allow ip rules to match it properly.

Problem [1] noticed by Shmulik Ladkani 

[1] http://marc.info/?t=137331755300040&r=1&w=2

Fixes: 89aef8921bfb ("ipv4: Delete routing cache.")
Signed-off-by: Julian Anastasov 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

ipv4: use new_gw for redirect neigh lookup

2016-11-28T21:22:40+00:00

[ Upstream commit 969447f226b451c453ddc83cac6144eaeac6f2e3 ]

In v2.6, ip_rt_redirect() calls arp_bind_neighbour() which returns 0
and then the state of the neigh for the new_gw is checked. If the state
isn't valid then the redirected route is deleted. This behavior is
maintained up to v3.5.7 by check_peer_redirect() because rt->rt_gateway
is assigned to peer->redirect_learned.a4 before calling
ipv4_neigh_lookup().

After commit 5943634fc559 ("ipv4: Maintain redirect and PMTU info in
struct rtable again."), ipv4_neigh_lookup() is performed without the
rt_gateway assigned to the new_gw. In the case when rt_gateway (old_gw)
isn't zero, the function uses it as the key. The neigh is most likely
valid since the old_gw is the one that sends the ICMP redirect message.
Then the new_gw is assigned to fib_nh_exception. The problem is: the
new_gw ARP may never gets resolved and the traffic is blackholed.

So, use the new_gw for neigh lookup.

Changes from v1:
 - use __ipv4_neigh_lookup instead (per Eric Dumazet).

Fixes: 5943634fc559 ("ipv4: Maintain redirect and PMTU info in struct rtable again.")
Signed-off-by: Stephen Suryaputra Lin 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

neigh: check error pointer instead of NULL for ipv4_neigh_lookup()

2016-11-28T21:22:39+00:00

commit 2c1a4311b61072afe2309d4152a7993e92caa41c upstream.

Fixes: commit f187bc6efb7250afee0e2009b6106 ("ipv4: No need to set generic neighbour pointer")
Cc: David S. Miller 
Signed-off-by: Cong Wang 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

ipmr, ip6mr: fix scheduling while atomic and a deadlock with ipmr_get_route

2016-11-24T15:24:04+00:00

[ Upstream commit 2cf750704bb6d7ed8c7d732e071dd1bc890ea5e8 ]

Since the commit below the ipmr/ip6mr rtnl_unicast() code uses the portid
instead of the previous dst_pid which was copied from in_skb's portid.
Since the skb is new the portid is 0 at that point so the packets are sent
to the kernel and we get scheduling while atomic or a deadlock (depending
on where it happens) by trying to acquire rtnl two times.
Also since this is RTM_GETROUTE, it can be triggered by a normal user.

Here's the sleeping while atomic trace:
[ 7858.212557] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
[ 7858.212748] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 7858.212881] 2 locks held by swapper/0/0:
[ 7858.213013]  #0:  (((&mrt->ipmr_expire_timer))){+.-...}, at: [] call_timer_fn+0x5/0x350
[ 7858.213422]  #1:  (mfc_unres_lock){+.....}, at: [] ipmr_expire_process+0x25/0x130
[ 7858.213807] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.8.0-rc7+ #179
[ 7858.213934] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 7858.214108]  0000000000000000 ffff88005b403c50 ffffffff813a7804 0000000000000000
[ 7858.214412]  ffffffff81a1338e ffff88005b403c78 ffffffff810a4a72 ffffffff81a1338e
[ 7858.214716]  000000000000026c 0000000000000000 ffff88005b403ca8 ffffffff810a4b9f
[ 7858.215251] Call Trace:
[ 7858.215412]    [] dump_stack+0x85/0xc1
[ 7858.215662]  [] ___might_sleep+0x192/0x250
[ 7858.215868]  [] __might_sleep+0x6f/0x100
[ 7858.216072]  [] mutex_lock_nested+0x33/0x4d0
[ 7858.216279]  [] ? netlink_lookup+0x25f/0x460
[ 7858.216487]  [] rtnetlink_rcv+0x1b/0x40
[ 7858.216687]  [] netlink_unicast+0x19c/0x260
[ 7858.216900]  [] rtnl_unicast+0x20/0x30
[ 7858.217128]  [] ipmr_destroy_unres+0xa9/0xf0
[ 7858.217351]  [] ipmr_expire_process+0x8f/0x130
[ 7858.217581]  [] ? ipmr_net_init+0x180/0x180
[ 7858.217785]  [] ? ipmr_net_init+0x180/0x180
[ 7858.217990]  [] call_timer_fn+0xa5/0x350
[ 7858.218192]  [] ? call_timer_fn+0x5/0x350
[ 7858.218415]  [] ? ipmr_net_init+0x180/0x180
[ 7858.218656]  [] run_timer_softirq+0x260/0x640
[ 7858.218865]  [] ? __do_softirq+0xbb/0x54f
[ 7858.219068]  [] __do_softirq+0xe8/0x54f
[ 7858.219269]  [] irq_exit+0xb8/0xc0
[ 7858.219463]  [] smp_apic_timer_interrupt+0x42/0x50
[ 7858.219678]  [] apic_timer_interrupt+0x8c/0xa0
[ 7858.219897]    [] ? native_safe_halt+0x6/0x10
[ 7858.220165]  [] ? trace_hardirqs_on+0xd/0x10
[ 7858.220373]  [] default_idle+0x23/0x190
[ 7858.220574]  [] arch_cpu_idle+0xf/0x20
[ 7858.220790]  [] default_idle_call+0x4c/0x60
[ 7858.221016]  [] cpu_startup_entry+0x39b/0x4d0
[ 7858.221257]  [] rest_init+0x135/0x140
[ 7858.221469]  [] start_kernel+0x50e/0x51b
[ 7858.221670]  [] ? early_idt_handler_array+0x120/0x120
[ 7858.221894]  [] x86_64_start_reservations+0x2a/0x2c
[ 7858.222113]  [] x86_64_start_kernel+0x13b/0x14a

Fixes: 2942e9005056 ("[RTNETLINK]: Use rtnl_unicast() for rtnetlink unicasts")
Signed-off-by: Nikolay Aleksandrov 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

route: do not cache fib route info on local routes with oif

2016-05-18T07:03:50+00:00

[ Upstream commit d6d5e999e5df67f8ec20b6be45e2229455ee3699 ]

For local routes that require a particular output interface we do not want
to cache the result.  Caching the result causes incorrect behaviour when
there are multiple source addresses on the interface.  The end result
being that if the intended recipient is waiting on that interface for the
packet he won't receive it because it will be delivered on the loopback
interface and the IP_PKTINFO ipi_ifindex will be set to the loopback
interface as well.

This can be tested by running a program such as "dhcp_release" which
attempts to inject a packet on a particular interface so that it is
received by another program on the same board.  The receiving process
should see an IP_PKTINFO ipi_ifndex value of the source interface
(e.g., eth1) instead of the loopback interface (e.g., lo).  The packet
will still appear on the loopback interface in tcpdump but the important
aspect is that the CMSG info is correct.

Sample dhcp_release command line:

   dhcp_release eth1 192.168.204.222 02:11:33:22:44:66

Signed-off-by: Allain Legacy 
Signed off-by: Chris Friesen 
Reviewed-by: Julian Anastasov 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

route: check and remove route cache when we get route

2016-03-02T15:29:14+00:00

[ Upstream commit deed49df7390d5239024199e249190328f1651e7 ]

Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.

Fix this issue by checking  and removing route cache when we get route.

Signed-off-by: Xin Long 
Acked-by: Hannes Frederic Sowa 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

route: Use ipv4_mtu instead of raw rt_pmtu

2016-01-09T10:32:43+00:00

commit cb6ccf09d6b94bec4def1ac5cf4678d12b216474 upstream.

The commit 3cdaa5be9e81a914e633a6be7b7d2ef75b528562 ("ipv4: Don't
increase PMTU with Datagram Too Big message") broke PMTU in cases
where the rt_pmtu value has expired but is smaller than the new
PMTU value.

This obsolete rt_pmtu then prevents the new PMTU value from being
installed.

Fixes: 3cdaa5be9e81 ("ipv4: Don't increase PMTU with Datagram Too Big message")
Reported-by: Gerd v. Egidy 
Signed-off-by: Herbert Xu 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

ipv4: Don't increase PMTU with Datagram Too Big message.

2016-01-09T10:32:06+00:00

commit 3cdaa5be9e81a914e633a6be7b7d2ef75b528562 upstream.

RFC 1191 said, "a host MUST not increase its estimate of the Path
MTU in response to the contents of a Datagram Too Big message."

Signed-off-by: Li Wei 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

ipv4: Avoid crashing in ip_error

2015-06-10T09:18:10+00:00

[ Upstream commit 381c759d9916c42959515ad34a6d467e24a88e93 ]

ip_error does not check if in_dev is NULL before dereferencing it.

IThe following sequence of calls is possible:
CPU A                          CPU B
ip_rcv_finish
    ip_route_input_noref()
        ip_route_input_slow()
                               inetdev_destroy()
    dst_input()

With the result that a network device can be destroyed while processing
an input packet.

A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device.   The error condition
was created by the removal of the network device.

As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.

Therefore handle this weird case by just dropping the packet if
!in_dev.  It will result in dropping the packet sooner, and will not
result in an actual change of behavior.

Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.")
Reported-by: Vittorio Gambaletta 
Tested-by: Vittorio Gambaletta 
Signed-off-by: Vittorio Gambaletta 
Signed-off-by: "Eric W. Biederman" 
Acked-by: Eric Dumazet 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby

ipv4: try to cache dst_entries which would cause a redirect

2015-02-10T10:16:49+00:00

[ Upstream commit df4d92549f23e1c037e83323aff58a21b3de7fe0 ]

Not caching dst_entries which cause redirects could be exploited by hosts
on the same subnet, causing a severe DoS attack. This effect aggravated
since commit f88649721268999 ("ipv4: fix dst race in sk_dst_get()").

Lookups causing redirects will be allocated with DST_NOCACHE set which
will force dst_release to free them via RCU.  Unfortunately waiting for
RCU grace period just takes too long, we can end up with >1M dst_entries
waiting to be released and the system will run OOM. rcuos threads cannot
catch up under high softirq load.

Attaching the flag to emit a redirect later on to the specific skb allows
us to cache those dst_entries thus reducing the pressure on allocation
and deallocation.

This issue was discovered by Marcelo Leitner.

Cc: Julian Anastasov 
Signed-off-by: Marcelo Leitner 
Signed-off-by: Florian Westphal 
Signed-off-by: Hannes Frederic Sowa 
Signed-off-by: Julian Anastasov 
Signed-off-by: David S. Miller 
Signed-off-by: Jiri Slaby