Add #define pr_fmt(fmt) as appropriate. Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files. Standardize on "UDPLite: " for appropriate uses. Some prefixes were previously "UDPLITE: " and "UDP-Lite: ". Add KBUILD_MODNAME ": " to icmp and gre. Remove embedded prefixes as appropriate. Add missing "\n" to pr_info in gre.c. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current kernel messaging style. Convert a printk block to print_hex_dump. Coalesce formats, align arguments. Use %s, __func__ instead of embedding function names. Some messages that were prefixed with <foo>_close are now prefixed with <foo>_fini. Some ah4 and esp messages are now not prefixed with "ip ". The intent of this patch is to later add something like #define pr_fmt(fmt) "IPv4: " fmt. to standardize the output messages. Text size is trivially reduced. (x86-32 allyesconfig) $ size net/ipv4/built-in.o* text data bss dec hex filename 887888 31558 249696 1169142 11d6f6 net/ipv4/built-in.o.new 887934 31558 249800 1169292 11d78c net/ipv4/built-in.o.old Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts: drivers/net/ethernet/sfc/rx.c Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change the rx_buf->is_page boolean into a set of u16 flags, and another to adjust how ->ip_summed is initialized. Signed-off-by: David S. Miller <davem@davemloft.net>
The original spelling and bad word choice makes these comments hard to read. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random() to set addr_assign_type correctly to NET_ADDR_RANDOM. Change the trivial cases. v2: adapt to renamed eth_hw_addr_random() Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion is very similar to that made to ipv6's SIT code. Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel devices set NETIF_F_LLTX to bypass HARD_TX_LOCK. Sit and ipip set this unconditionally in ops->setup, but gre enables it conditionally after parameter passing in ops->newlink. This is not called during tunnel setup as below, however, so GRE tunnels are still taking the lock. modprobe ip_gre ip tunnel add test0 mode gre remote 10.5.1.1 dev lo ip link set test0 up ip addr add 10.6.0.1 dev test0 # cat /sys/class/net/test0/features # $DIR/test_tunnel_xmit 10 10.5.2.1 ip route add 10.5.2.0/24 dev test0 ip tunnel del test0 The newlink callback is only called in rtnl_netlink, and only if the device is new, as it calls register_netdevice internally. Gre tunnels are created at 'ip tunnel add' with ioctl SIOCADDTUNNEL, which calls ipgre_tunnel_locate, which calls register_netdev. rtnl_newlink is called at 'ip link set', but skips ops->newlink and the device is up with locking still enabled. The equivalent ipip tunnel works fine, btw (just substitute 'method gre' for 'method ipip'). On kernels before /sys/class/net/*/features was removed [1], the first commented out line returns 0x6000 with method gre, which indicates that NETIF_F_LLTX (0x1000) is not set. With ipip, it reports 0x7000. This test cannot be used on recent kernels where the sysfs file is removed (and ETHTOOL_GFEATURES does not currently work for tunnel devices, because they lack dev->ethtool_ops). The second commented out line calls a simple transmission test [2] that sends on 24 cores at maximum rate. Results of a single run: ipip: 19,372,306 gre before patch: 4,839,753 gre after patch: 19,133,873 This patch replicates the condition check in ipgre_newlink to ipgre_tunnel_locate. It works for me, both with oseq on and off. This is the first time I looked at rtnetlink and iproute2 code, though, so someone more knowledgeable should probably check the patch. Thanks. The tail of both functions is now identical, by the way. To avoid code duplication, I'll be happy to rework this and merge the two. [1] http://patchwork.ozlabs.org/patch/104610/ [2] http://kernel.googlecode.com/files/xmit_udp_parallel.c Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove the rt_gateway == 0 check but we shouldn't remove the 'dst' initialization too. Noticed by Eric Dumazet. Signed-off-by: David S. Miller <davem@davemloft.net>
It can never actually happen. rt_gateway is either the fully resolved flow lookup key's destination address, or the non-zero FIB entry gateway address. Signed-off-by: David S. Miller <davem@davemloft.net>