linux-stable.git/net/ipv4/arp.c, branch linux-4.3.y

ipv4: fix reply_dst leakage on arp reply

2015-10-05T11:05:15+00:00

There are cases when the created metadata reply is not used. Ensure the
allocated memory is freed also in such cases.

Fixes: 63d008a4e9ee ("ipv4: send arp replies to the correct tunnel")
Reported-by: Hannes Frederic Sowa 
Signed-off-by: Jiri Benc 
Signed-off-by: David S. Miller

ipv4: send arp replies to the correct tunnel

2015-09-24T21:31:36+00:00

When using ip lwtunnels, the additional data for xmit (basically, the actual
tunnel to use) are carried in ip_tunnel_info either in dst->lwtstate or in
metadata dst. When replying to ARP requests, we need to send the reply to
the same tunnel the request came from. This means we need to construct
proper metadata dst for ARP replies.

We could perform another route lookup to get a dst entry with the correct
lwtstate. However, this won't always ensure that the outgoing tunnel is the
same as the incoming one, and it won't work anyway for IPv4 duplicate
address detection.

The only thing to do is to "reverse" the ip_tunnel_info.

Signed-off-by: Jiri Benc 
Acked-by: Thomas Graf 
Signed-off-by: David S. Miller

net: Fix up inet_addr_type checks

2015-08-14T05:43:21+00:00

Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.

inet_addr_type_dev_table keeps the same semantics as inet_addr_type but
if the passed in device is enslaved to a VRF then the table for that VRF
is used for the lookup.

Signed-off-by: David Ahern 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2015-08-01T06:52:20+00:00

Conflicts:
	arch/s390/net/bpf_jit_comp.c
	drivers/net/ethernet/ti/netcp_ethss.c
	net/bridge/br_multicast.c
	net/ipv4/ip_fragment.c

All four conflicts were cases of simple overlapping
changes.

Signed-off-by: David S. Miller

arp: filter NOARP neighbours for SIOCGARP

2015-07-29T06:41:24+00:00

When arp is off on a device, and ioctl(SIOCGARP) is queried,
a buggy answer is given with MAC address of the device, instead
of the mac address of the destination/gateway.

We filter out NUD_NOARP neighbours for /proc/net/arp,
we must do the same for SIOCGARP ioctl.

Tested:

lpaa23:~# ./arp 10.246.7.190
MAC=00:01:e8:22:cb:1d      // correct answer

lpaa23:~# ip link set dev eth0 arp off
lpaa23:~# cat /proc/net/arp   # check arp table is now 'empty'
IP address       HW type     Flags       HW address    Mask     Device
lpaa23:~# ./arp 10.246.7.190
MAC=00:1a:11:c3:0d:7f   // buggy answer before patch (this is eth0 mac)

After patch :

lpaa23:~# ip link set dev eth0 arp off
lpaa23:~# ./arp 10.246.7.190
ioctl(SIOCGARP) failed: No such device or address

Signed-off-by: Eric Dumazet 
Reported-by: Vytautas Valancius 
Cc: Willem de Bruijn 
Signed-off-by: David S. Miller

arp: Inherit metadata dst when creating ARP requests

2015-07-21T17:39:05+00:00

If output device wants to see the dst, inherit the dst of the
original skb and pass it on to generate the ARP request.

Signed-off-by: Thomas Graf 
Signed-off-by: David S. Miller

netfilter: Pass socket pointer down through okfn().

2015-04-07T19:25:55+00:00

On the output paths in particular, we have to sometimes deal with two
socket contexts.  First, and usually skb->sk, is the local socket that
generated the frame.

And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.

We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.

The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device.  We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.

Signed-off-by: David S. Miller

ipv4: coding style: comparison for inequality with NULL

2015-04-03T16:11:15+00:00

The ipv4 code uses a mixture of coding styles. In some instances check
for non-NULL pointer is done as x != NULL and sometimes as x. x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.

No changes detected by objdiff.

Signed-off-by: Ian Morris 
Signed-off-by: David S. Miller

ipv4: coding style: comparison for equality with NULL

2015-04-03T16:11:15+00:00

The ipv4 code uses a mixture of coding styles. In some instances check
for NULL pointer is done as x == NULL and sometimes as !x. !x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.

No changes detected by objdiff.

Signed-off-by: Ian Morris 
Signed-off-by: David S. Miller

neigh: Factor out ___neigh_lookup_noref

2015-03-04T05:23:23+00:00

While looking at the mpls code I found myself writing yet another
version of neigh_lookup_noref.  We currently have __ipv4_lookup_noref
and __ipv6_lookup_noref.

So to make my work a little easier and to make it a smidge easier to
verify/maintain the mpls code in the future I stopped and wrote
___neigh_lookup_noref.  Then I rewote __ipv4_lookup_noref and
__ipv6_lookup_noref in terms of this new function.  I tested my new
version by verifying that the same code is generated in
ip_finish_output2 and ip6_finish_output2 where these functions are
inlined.

To get to ___neigh_lookup_noref I added a new neighbour cache table
function key_eq.  So that the static size of the key would be
available.

I also added __neigh_lookup_noref for people who want to to lookup
a neighbour table entry quickly but don't know which neibhgour table
they are going to look up.

Signed-off-by: "Eric W. Biederman" 
Signed-off-by: David S. Miller