linux-stable.git/net/hsr, branch linux-5.11.y

net: hsr: Reset MAC header for Tx path

2021-04-14T06:47:13+00:00

commit 9d6803921a16f4d768dc41a75375629828f4d91e upstream.

Reset MAC header in HSR Tx path. This is needed, because direct packet
transmission, e.g. by specifying PACKET_QDISC_BYPASS does not reset the MAC
header.

This has been observed using the following setup:

|$ ip link add name hsr0 type hsr slave1 lan0 slave2 lan1 supervision 45 version 1
|$ ifconfig hsr0 up
|$ ./test hsr0

The test binary is using mmap'ed sockets and is specifying the
PACKET_QDISC_BYPASS socket option.

This patch resolves the following warning on a non-patched kernel:

|[  112.725394] ------------[ cut here ]------------
|[  112.731418] WARNING: CPU: 1 PID: 257 at net/hsr/hsr_forward.c:560 hsr_forward_skb+0x484/0x568
|[  112.739962] net/hsr/hsr_forward.c:560: Malformed frame (port_src hsr0)

The warning can be safely removed, because the other call sites of
hsr_forward_skb() make sure that the skb is prepared correctly.

Fixes: d346a3fae3ff ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Kurt Kanzenbach 
Reviewed-by: Eric Dumazet 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: hsr: add support for EntryForgetTime

2021-03-07T11:35:47+00:00

commit f176411401127a07a9360dec14eca448eb2e9d45 upstream.

In IEC 62439-3 EntryForgetTime is defined with a value of 400 ms. When a
node does not send any frame within this time, the sequence number check
for can be ignored. This solves communication issues with Cisco IE 2000
in Redbox mode.

Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Marco Wenzel 
Reviewed-by: George McCollister 
Tested-by: George McCollister 
Reviewed-by: Andrew Lunn 
Link: https://lore.kernel.org/r/20210224094653.1440-1-marco.wenzel@a-eberle.de
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

net: hsr: align sup_multicast_addr in struct hsr_priv to u16 boundary

2021-02-02T16:57:18+00:00

sup_multicast_addr is passed to ether_addr_equal for address comparison
which casts the address inputs to u16 leading to an unaligned access.
Aligning the sup_multicast_addr to u16 boundary fixes the issue.

Signed-off-by: Andreas Oetken 
Link: https://lore.kernel.org/r/20210202090304.2740471-1-ennoerlangen@gmail.com
Signed-off-by: Jakub Kicinski

genetlink: move to smaller ops wherever possible

2020-10-03T02:11:11+00:00

Bulk of the genetlink users can use smaller ops, move them.

Signed-off-by: Jakub Kicinski 
Reviewed-by: Johannes Berg 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2020-09-22T23:45:34+00:00

Two minor conflicts:

1) net/ipv4/route.c, adding a new local variable while
   moving another local variable and removing it's
   initial assignment.

2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
   One pretty prints the port mode differently, whilst another
   changes the driver to try and obtain the port mode from
   the port node rather than the switch node.

Signed-off-by: David S. Miller

net: hsr: Convert to DEFINE_SHOW_ATTRIBUTE

2020-09-18T00:05:10+00:00

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.

Signed-off-by: Qinglang Miao 
Signed-off-by: David S. Miller

hsr: avoid newline at end of message in NL_SET_ERR_MSG_MOD

2020-09-09T18:15:26+00:00

clean follow coccicheck warning:
net//hsr/hsr_netlink.c:94:8-42: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
net//hsr/hsr_netlink.c:87:30-57: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
net//hsr/hsr_netlink.c:79:29-53: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD

Signed-off-by: Ye Bin 
Signed-off-by: David S. Miller

hsr: Use %pM format specifier for MAC addresses

2020-07-31T23:46:26+00:00

Convert to %pM instead of using custom code.

Signed-off-by: Andy Shevchenko 
Signed-off-by: David S. Miller

net: prp: enhance debugfs to display PRP info

2020-07-27T19:20:40+00:00

Print PRP specific information from node table as part of debugfs
node table display. Also display the node as DAN-H or DAN-P depending
on the info from node table.

Signed-off-by: Murali Karicheri 
Signed-off-by: David S. Miller

net: prp: add packet handling support

2020-07-27T19:20:40+00:00

DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads.  This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.

Signed-off-by: Murali Karicheri 
Signed-off-by: David S. Miller