Pull networking updates from Jakub Kicinski:
 "Core & protocols:

   - Wrap datapath globals into net_aligned_data, to avoid false sharing

   - Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)

   - Add SO_INQ and SCM_INQ support to AF_UNIX

   - Add SIOCINQ support to AF_VSOCK

   - Add TCP_MAXSEG sockopt to MPTCP

   - Add IPv6 force_forwarding sysctl to enable forwarding per interface

   - Make TCP validation of whether packet fully fits in the receive
     window and the rcv_buf more strict. With increased use of HW
     aggregation a single "packet" can be multiple 100s of kB

   - Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
     improves latency up to 33% for sockmap users

   - Convert TCP send queue handling from tasklet to BH workque

   - Improve BPF iteration over TCP sockets to see each socket exactly
     once

   - Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code

   - Support enabling kernel threads for NAPI processing on per-NAPI
     instance basis rather than a whole device. Fully stop the kernel
     NAPI thread when threaded NAPI gets disabled. Previously thread
     would stick around until ifdown due to tricky synchronization

   - Allow multicast routing to take effect on locally-generated packets

   - Add output interface argument for End.X in segment routing

   - MCTP: add support for gateway routing, improve bind() handling

   - Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink

   - Add a new neighbor flag ("extern_valid"), which cedes refresh
     responsibilities to userspace. This is needed for EVPN multi-homing
     where a neighbor entry for a multi-homed host needs to be synced
     across all the VTEPs among which the host is multi-homed

   - Support NUD_PERMANENT for proxy neighbor entries

   - Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM

   - Add sequence numbers to netconsole messages. Unregister
     netconsole's console when all net targets are removed. Code
     refactoring. Add a number of selftests

   - Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
     should be used for an inbound SA lookup

   - Support inspecting ref_tracker state via DebugFS

   - Don't force bonding advertisement frames tx to ~333 ms boundaries.
     Add broadcast_neighbor option to send ARP/ND on all bonded links

   - Allow providing upcall pid for the 'execute' command in openvswitch

   - Remove DCCP support from Netfilter's conntrack

   - Disallow multiple packet duplications in the queuing layer

   - Prevent use of deprecated iptables code on PREEMPT_RT

  Driver API:

   - Support RSS and hashing configuration over ethtool Netlink

   - Add dedicated ethtool callbacks for getting and setting hashing
     fields

   - Add support for power budget evaluation strategy in PSE /
     Power-over-Ethernet. Generate Netlink events for overcurrent etc

   - Support DPLL phase offset monitoring across all device inputs.
     Support providing clock reference and SYNC over separate DPLL
     inputs

   - Support traffic classes in devlink rate API for bandwidth
     management

   - Remove rtnl_lock dependency from UDP tunnel port configuration

  Device drivers:

   - Add a new Broadcom driver for 800G Ethernet (bnge)

   - Add a standalone driver for Microchip ZL3073x DPLL

   - Remove IBM's NETIUCV device driver

   - Ethernet high-speed NICs:
      - Broadcom (bnxt):
         - support zero-copy Tx of DMABUF memory
         - take page size into account for page pool recycling rings
      - Intel (100G, ice, idpf):
         - idpf: XDP and AF_XDP support preparations
         - idpf: add flow steering
         - add link_down_events statistic
         - clean up the TSPLL code
         - preparations for live VM migration
      - nVidia/Mellanox:
         - support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
         - optimize context memory usage for matchers
         - expose serial numbers in devlink info
         - support PCIe congestion metrics
      - Meta (fbnic):
         - add 25G, 50G, and 100G link modes to phylink
         - support dumping FW logs
      - Marvell/Cavium:
         - support for CN20K generation of the Octeon chips
      - Amazon:
         - add HW clock (without timestamping, just hypervisor time access)

   - Ethernet virtual:
      - VirtIO net:
         - support segmentation of UDP-tunnel-encapsulated packets
      - Google (gve):
         - support packet timestamping and clock synchronization
      - Microsoft vNIC:
         - add handler for device-originated servicing events
         - allow dynamic MSI-X vector allocation
         - support Tx bandwidth clamping

   - Ethernet NICs consumer, and embedded:
      - AMD:
         - amd-xgbe: hardware timestamping and PTP clock support
      - Broadcom integrated MACs (bcmgenet, bcmasp):
         - use napi_complete_done() return value to support NAPI polling
         - add support for re-starting auto-negotiation
      - Broadcom switches (b53):
         - support BCM5325 switches
         - add bcm63xx EPHY power control
      - Synopsys (stmmac):
         - lots of code refactoring and cleanups
      - TI:
         - icssg-prueth: read firmware-names from device tree
         - icssg: PRP offload support
      - Microchip:
         - lan78xx: convert to PHYLINK for improved PHY and MAC management
         - ksz: add KSZ8463 switch support
      - Intel:
         - support similar queue priority scheme in multi-queue and
           time-sensitive networking (taprio)
         - support packet pre-emption in both
      - RealTek (r8169):
         - enable EEE at 5Gbps on RTL8126
      - Airoha:
         - add PPPoE offload support
         - MDIO bus controller for Airoha AN7583

   - Ethernet PHYs:
      - support for the IPQ5018 internal GE PHY
      - micrel KSZ9477 switch-integrated PHYs:
         - add MDI/MDI-X control support
         - add RX error counters
         - add cable test support
         - add Signal Quality Indicator (SQI) reporting
      - dp83tg720: improve reset handling and reduce link recovery time
      - support bcm54811 (and its MII-Lite interface type)
      - air_en8811h: support resume/suspend
      - support PHY counters for QCA807x and QCA808x
      - support WoL for QCA807x

   - CAN drivers:
      - rcar_canfd: support for Transceiver Delay Compensation
      - kvaser: report FW versions via devlink dev info

   - WiFi:
      - extended regulatory info support (6 GHz)
      - add statistics and beacon monitor for Multi-Link Operation (MLO)
      - support S1G aggregation, improve S1G support
      - add Radio Measurement action fields
      - support per-radio RTS threshold
      - some work around how FIPS affects wifi, which was wrong (RC4 is
        used by TKIP, not only WEP)
      - improvements for unsolicited probe response handling

   - WiFi drivers:
      - RealTek (rtw88):
         - IBSS mode for SDIO devices
      - RealTek (rtw89):
         - BT coexistence for MLO/WiFi7
         - concurrent station + P2P support
         - support for USB devices RTL8851BU/RTL8852BU
      - Intel (iwlwifi):
         - use embedded PNVM in (to be released) FW images to fix
           compatibility issues
         - many cleanups (unused FW APIs, PCIe code, WoWLAN)
         - some FIPS interoperability
      - MediaTek (mt76):
         - firmware recovery improvements
         - more MLO work
      - Qualcomm/Atheros (ath12k):
         - fix scan on multi-radio devices
         - more EHT/Wi-Fi 7 features
         - encapsulation/decapsulation offload
      - Broadcom (brcm80211):
         - support SDIO 43751 device

   - Bluetooth:
      - hci_event: add support for handling LE BIG Sync Lost event
      - ISO: add socket option to report packet seqnum via CMSG
      - ISO: support SCM_TIMESTAMPING for ISO TS

   - Bluetooth drivers:
      - intel_pcie: support Function Level Reset
      - nxpuart: add support for 4M baudrate
      - nxpuart: implement powerup sequence, reset, FW dump, and FW loading"

* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
  dpll: zl3073x: Fix build failure
  selftests: bpf: fix legacy netfilter options
  ipv6: annotate data-races around rt->fib6_nsiblings
  ipv6: fix possible infinite loop in fib6_info_uses_dev()
  ipv6: prevent infinite loop in rt6_nlmsg_size()
  ipv6: add a retry logic in net6_rt_notify()
  vrf: Drop existing dst reference in vrf_ip6_input_dst
  net/sched: taprio: align entry index attr validation with mqprio
  net: fsl_pq_mdio: use dev_err_probe
  selftests: rtnetlink.sh: remove esp4_offload after test
  vsock: remove unnecessary null check in vsock_getname()
  igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
  stmmac: xsk: fix negative overflow of budget in zerocopy mode
  dt-bindings: ieee802154: Convert at86rf230.txt yaml format
  net: dsa: microchip: Disable PTP function of KSZ8463
  net: dsa: microchip: Setup fiber ports for KSZ8463
  net: dsa: microchip: Write switch MAC address differently for KSZ8463
  net: dsa: microchip: Use different registers for KSZ8463
  net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
  dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
  ...

Found by codespell.

Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This code (tty_get -> vhangup -> tty_put) is repeated on few places.
Introduce a helper similar to tty_port_tty_hangup() (asynchronous) to
handle even vhangup (synchronous).

And use it on those places.

In fact, reuse the tty_port_tty_hangup()'s code and call tty_vhangup()
depending on a new bool parameter.

Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move this API to the canonical timer_*() namespace.

[ tglx: Redone against pre rc1 ]

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com

timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.

Conversion was done with coccinelle plus manual fixups where necessary.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

This reverts commit 4d94f05558271654670d18c26c912da0c1c15549 which has
problems (see [1]) and is no longer needed since 581dd2dc168f
("Bluetooth: hci_event: Fix using rcu_read_(un)lock while iterating")
has reworked the code where the original bug has been found.

[1] Link: https://lore.kernel.org/linux-bluetooth/877c55ci1r.wl-tiwai@suse.de/T/#t
Fixes: 4d94f0555827 ("Bluetooth: hci_core: Fix sleeping function called from invalid context")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Use usb_autopm_get_interface() and usb_autopm_put_interface()
in btmtk_usb_shutdown(), it could send func ctrl after enabling
autosuspend.

Bluetooth: btmtk_usb_hci_wmt_sync() hci0: Execution of wmt command
           timed out
Bluetooth: btmtk_usb_shutdown() hci0: Failed to send wmt func ctrl
           (-110)

Fixes: 5c5e8c52e3ca ("Bluetooth: btmtk: move btusb_mtk_[setup, shutdown] to btmtk.c")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This reworks hci_cb_list to not use mutex hci_cb_list_lock to avoid bugs
like the bellow:

BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585
in_atomic(): 0, irqs_disabled(): 0, non_block: 0, pid: 5070, name: kworker/u9:2
preempt_count: 0, expected: 0
RCU nest depth: 1, expected: 0
4 locks held by kworker/u9:2/5070:
 #0: ffff888015be3948 ((wq_completion)hci0#2){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3229 [inline]
 #0: ffff888015be3948 ((wq_completion)hci0#2){+.+.}-{0:0}, at: process_scheduled_works+0x8e0/0x1770 kernel/workqueue.c:3335
 #1: ffffc90003b6fd00 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3230 [inline]
 #1: ffffc90003b6fd00 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0}, at: process_scheduled_works+0x91b/0x1770 kernel/workqueue.c:3335
 #2: ffff8880665d0078 (&hdev->lock){+.+.}-{3:3}, at: hci_le_create_big_complete_evt+0xcf/0xae0 net/bluetooth/hci_event.c:6914
 #3: ffffffff8e132020 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:298 [inline]
 #3: ffffffff8e132020 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:750 [inline]
 #3: ffffffff8e132020 (rcu_read_lock){....}-{1:2}, at: hci_le_create_big_complete_evt+0xdb/0xae0 net/bluetooth/hci_event.c:6915
CPU: 0 PID: 5070 Comm: kworker/u9:2 Not tainted 6.8.0-syzkaller-08073-g480e035fc4c7 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
Workqueue: hci0 hci_rx_work
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
 __might_resched+0x5d4/0x780 kernel/sched/core.c:10187
 __mutex_lock_common kernel/locking/mutex.c:585 [inline]
 __mutex_lock+0xc1/0xd70 kernel/locking/mutex.c:752
 hci_connect_cfm include/net/bluetooth/hci_core.h:2004 [inline]
 hci_le_create_big_complete_evt+0x3d9/0xae0 net/bluetooth/hci_event.c:6939
 hci_event_func net/bluetooth/hci_event.c:7514 [inline]
 hci_event_packet+0xa53/0x1540 net/bluetooth/hci_event.c:7569
 hci_rx_work+0x3e8/0xca0 net/bluetooth/hci_core.c:4171
 process_one_work kernel/workqueue.c:3254 [inline]
 process_scheduled_works+0xa00/0x1770 kernel/workqueue.c:3335
 worker_thread+0x86d/0xd70 kernel/workqueue.c:3416
 kthread+0x2f0/0x390 kernel/kthread.c:388
 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:243
 </TASK>

Reported-by: syzbot+2fb0835e0c9cefc34614@syzkaller.appspotmail.com
Tested-by: syzbot+2fb0835e0c9cefc34614@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2fb0835e0c9cefc34614
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The bt_copy_from_sockptr() return value is being misinterpreted by most
users: a non-zero result is mistakenly assumed to represent an error code,
but actually indicates the number of bytes that could not be copied.

Remove bt_copy_from_sockptr() and adapt callers to use
copy_safe_from_sockptr().

For sco_sock_setsockopt() (case BT_CODEC) use copy_struct_from_sockptr() to
scrub parts of uninitialized buffer.

Opportunistically, rename `len` to `optlen` in hci_sock_setsockopt_old()
and hci_sock_setsockopt().

Fixes: 51eda36d33e4 ("Bluetooth: SCO: Fix not validating setsockopt user input")
Fixes: a97de7bff13b ("Bluetooth: RFCOMM: Fix not validating setsockopt user input")
Fixes: 4f3951242ace ("Bluetooth: L2CAP: Fix not validating setsockopt user input")
Fixes: 9e8742cdfc4b ("Bluetooth: ISO: Fix not validating setsockopt user input")
Fixes: b2186061d604 ("Bluetooth: hci_sock: Fix not validating setsockopt user input")
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: David Wei <dw@davidwei.uk>
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Commit 9bf4e919ccad worked around an issue introduced after an innocuous
optimisation change in LLVM main:

> len is defined as an 'int' because it is assigned from
> '__user int *optlen'. However, it is clamped against the result of
> sizeof(), which has a type of 'size_t' ('unsigned long' for 64-bit
> platforms). This is done with min_t() because min() requires compatible
> types, which results in both len and the result of sizeof() being casted
> to 'unsigned int', meaning len changes signs and the result of sizeof()
> is truncated. From there, len is passed to copy_to_user(), which has a
> third parameter type of 'unsigned long', so it is widened and changes
> signs again. This excessive casting in combination with the KCSAN
> instrumentation causes LLVM to fail to eliminate the __bad_copy_from()
> call, failing the build.

The same issue occurs in rfcomm in functions rfcomm_sock_getsockopt and
rfcomm_sock_getsockopt_old.

Change the type of len to size_t in both rfcomm_sock_getsockopt and
rfcomm_sock_getsockopt_old and replace min_t() with min().

Cc: stable@vger.kernel.org
Co-authored-by: Aleksei Vetrov <vvvvvv@google.com>
Improves: 9bf4e919ccad ("Bluetooth: Fix type of len in {l2cap,sco}_sock_getsockopt_old()")
Link: https://github.com/ClangBuiltLinux/linux/issues/2007
Link: https://github.com/llvm/llvm-project/issues/85647
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>