Several spots in the kernel perform a sequence like:

	skb_queue_tail(&sk->s_receive_queue, skb);
	sk->sk_data_ready(sk, skb->len);

But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up.  So this skb->len access is potentially
to freed up memory.

Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.

And finally, no actual implementation of this callback actually uses
the length argument.  And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.

So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.

Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.

Signed-off-by: David S. Miller <davem@davemloft.net>

We should let user space request the peer address also in the pending
connect states, i.e. BT_CONNECT and BT_CONNECT2. There is existing user
space code that tries to do this and will fail without extending the set
of allowed states for the peer address information.

This patch adds the two states to the allowed ones in the L2CAP and
RFCOMM sock_getname functions, thereby preventing ENOTCONN from being
returned.

Reported-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When binding RFCOMM socket with non-zero channel we're checking if
there is already any other socket which has the same channel number
assigned and then fail. This check does not consider situation where
we have another socket connected to remote device on given channel
number in which case we still should be able to bind local socket.

This patch changes __rfcomm_get_sock_by_addr() to return only sockets
in either BT_BOUND or BT_LISTEN states, also name is updated to better
describe what this function does now.

Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The skb truesize of a 12-byte payload with a 10-byte head/tail
reserve is 768 bytes. Consequently, even with 40 tx_credits, at
most 6 packets could be queued at any one time:

  40 tx_credits * 127-byte mtu < 768-byte truesize * 7

This error could also cause the tx queue to apparently stall if
credit flow control is disabled (where tx_credits is fixed at 5),
or if the receiver only granted a limited number of tx credits
(eg., less than 7).

Instead, track the outstanding number of queued packets not yet sent
in wmem_alloc and allow for a maximum of 40 queued packets. Report
the space avail for a single write() as the mtu * number of packets
left before reaching the maximum.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Compute the amount of space available for a single write()
within rfcomm_room(); clamp to 0 for negative values. Note
this patch does not change the result of the computation.

Report the amount of room returned in the debug printk.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The tty driver api design prefers no-fail writes if the driver
write_room() method has previously indicated space is available
to accept writes. Since this is trivially possible for the
RFCOMM tty driver, do so.

Introduce rfcomm_dlc_send_noerror(), which queues but does not
schedule the krfcomm thread if the dlc is not yet connected
(and thus does not error based on the connection state).
The mtu size test is also unnecessary since the caller already
chunks the written data into mtu size.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If rfcomm_dlc_open() fails, set tty into error state which returns
-EIO from reads and writes.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If RFCOMM tty device registration fails, cleanup by releasing
the tty_port reference to trigger rfcomm_dev destruction
(rather than open-coding it).

The dlc reference release is moved into rfcomm_dev_add(),
which ensures cleanup in both error paths -- ie., if
__rfcomm_dev_add() fails or if tty_port_register_device() fails.

Fixes releasing the module reference if device registration fails.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Move rfcomm_dev allocation and initialization into new function,
__rfcomm_dev_add(), to simplify resource release in error handling.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>