linux-stable.git/kernel/trace/ftrace.c, branch v5.4.166 Linux kernel stable tree tracing: Have all levels of checks prevent recursion 2021-10-27T07:54:29+00:00 Steven Rostedt (VMware) rostedt@goodmis.org 2021-10-18T19:44:12+00:00 a98c81ab17511704c1140a48b57906a9661cb3f0 commit ed65df63a39a3f6ed04f7258de8b6789e5021c18 upstream. While writing an email explaining the "bit = 0" logic for a discussion on making ftrace_test_recursion_trylock() disable preemption, I discovered a path that makes the "not do the logic if bit is zero" unsafe. The recursion logic is done in hot paths like the function tracer. Thus, any code executed causes noticeable overhead. Thus, tricks are done to try to limit the amount of code executed. This included the recursion testing logic. Having recursion testing is important, as there are many paths that can end up in an infinite recursion cycle when tracing every function in the kernel. Thus protection is needed to prevent that from happening. Because it is OK to recurse due to different running context levels (e.g. an interrupt preempts a trace, and then a trace occurs in the interrupt handler), a set of bits are used to know which context one is in (normal, softirq, irq and NMI). If a recursion occurs in the same level, it is prevented*. Then there are infrastructure levels of recursion as well. When more than one callback is attached to the same function to trace, it calls a loop function to iterate over all the callbacks. Both the callbacks and the loop function have recursion protection. The callbacks use the "ftrace_test_recursion_trylock()" which has a "function" set of context bits to test, and the loop function calls the internal trace_test_and_set_recursion() directly, with an "internal" set of bits. If an architecture does not implement all the features supported by ftrace then the callbacks are never called directly, and the loop function is called instead, which will implement the features of ftrace. Since both the loop function and the callbacks do recursion protection, it was seemed unnecessary to do it in both locations. Thus, a trick was made to have the internal set of recursion bits at a more significant bit location than the function bits. Then, if any of the higher bits were set, the logic of the function bits could be skipped, as any new recursion would first have to go through the loop function. This is true for architectures that do not support all the ftrace features, because all functions being traced must first go through the loop function before going to the callbacks. But this is not true for architectures that support all the ftrace features. That's because the loop function could be called due to two callbacks attached to the same function, but then a recursion function inside the callback could be called that does not share any other callback, and it will be called directly. i.e. traced_function_1: [ more than one callback tracing it ] call loop_func loop_func: trace_recursion set internal bit call callback callback: trace_recursion [ skipped because internal bit is set, return 0 ] call traced_function_2 traced_function_2: [ only traced by above callback ] call callback callback: trace_recursion [ skipped because internal bit is set, return 0 ] call traced_function_2 [ wash, rinse, repeat, BOOM! out of shampoo! ] Thus, the "bit == 0 skip" trick is not safe, unless the loop function is call for all functions. Since we want to encourage architectures to implement all ftrace features, having them slow down due to this extra logic may encourage the maintainers to update to the latest ftrace features. And because this logic is only safe for them, remove it completely. [*] There is on layer of recursion that is allowed, and that is to allow for the transition between interrupt context (normal -> softirq -> irq -> NMI), because a trace may occur before the context update is visible to the trace recursion logic. Link: https://lore.kernel.org/all/609b565a-ed6e-a1da-f025-166691b5d994@linux.alibaba.com/ Link: https://lkml.kernel.org/r/20211018154412.09fcad3c@gandalf.local.home Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <James.Bottomley@hansenpartnership.com> Cc: Helge Deller <deller@gmx.de> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Jisheng Zhang <jszhang@kernel.org> Cc: =?utf-8?b?546L6LSH?= <yun.wang@linux.alibaba.com> Cc: Guo Ren <guoren@kernel.org> Cc: stable@vger.kernel.org Fixes: edc15cafcbfa3 ("tracing: Avoid unnecessary multiple recursion checks") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit ed65df63a39a3f6ed04f7258de8b6789e5021c18 upstream.

While writing an email explaining the "bit = 0" logic for a discussion on
making ftrace_test_recursion_trylock() disable preemption, I discovered a
path that makes the "not do the logic if bit is zero" unsafe.

The recursion logic is done in hot paths like the function tracer. Thus,
any code executed causes noticeable overhead. Thus, tricks are done to try
to limit the amount of code executed. This included the recursion testing
logic.

Having recursion testing is important, as there are many paths that can
end up in an infinite recursion cycle when tracing every function in the
kernel. Thus protection is needed to prevent that from happening.

Because it is OK to recurse due to different running context levels (e.g.
an interrupt preempts a trace, and then a trace occurs in the interrupt
handler), a set of bits are used to know which context one is in (normal,
softirq, irq and NMI). If a recursion occurs in the same level, it is
prevented*.

Then there are infrastructure levels of recursion as well. When more than
one callback is attached to the same function to trace, it calls a loop
function to iterate over all the callbacks. Both the callbacks and the
loop function have recursion protection. The callbacks use the
"ftrace_test_recursion_trylock()" which has a "function" set of context
bits to test, and the loop function calls the internal
trace_test_and_set_recursion() directly, with an "internal" set of bits.

If an architecture does not implement all the features supported by ftrace
then the callbacks are never called directly, and the loop function is
called instead, which will implement the features of ftrace.

Since both the loop function and the callbacks do recursion protection, it
was seemed unnecessary to do it in both locations. Thus, a trick was made
to have the internal set of recursion bits at a more significant bit
location than the function bits. Then, if any of the higher bits were set,
the logic of the function bits could be skipped, as any new recursion
would first have to go through the loop function.

This is true for architectures that do not support all the ftrace
features, because all functions being traced must first go through the
loop function before going to the callbacks. But this is not true for
architectures that support all the ftrace features. That's because the
loop function could be called due to two callbacks attached to the same
function, but then a recursion function inside the callback could be
called that does not share any other callback, and it will be called
directly.

i.e.

 traced_function_1: [ more than one callback tracing it ]
   call loop_func

 loop_func:
   trace_recursion set internal bit
   call callback

 callback:
   trace_recursion [ skipped because internal bit is set, return 0 ]
   call traced_function_2

 traced_function_2: [ only traced by above callback ]
   call callback

 callback:
   trace_recursion [ skipped because internal bit is set, return 0 ]
   call traced_function_2

 [ wash, rinse, repeat, BOOM! out of shampoo! ]

Thus, the "bit == 0 skip" trick is not safe, unless the loop function is
call for all functions.

Since we want to encourage architectures to implement all ftrace features,
having them slow down due to this extra logic may encourage the
maintainers to update to the latest ftrace features. And because this
logic is only safe for them, remove it completely.

 [*] There is on layer of recursion that is allowed, and that is to allow
     for the transition between interrupt context (normal -> softirq ->
     irq -> NMI), because a trace may occur before the context update is
     visible to the trace recursion logic.

Link: https://lore.kernel.org/all/609b565a-ed6e-a1da-f025-166691b5d994@linux.alibaba.com/
Link: https://lkml.kernel.org/r/20211018154412.09fcad3c@gandalf.local.home

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <James.Bottomley@hansenpartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Jisheng Zhang <jszhang@kernel.org>
Cc: =?utf-8?b?546L6LSH?= <yun.wang@linux.alibaba.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: stable@vger.kernel.org
Fixes: edc15cafcbfa3 ("tracing: Avoid unnecessary multiple recursion checks")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ftrace: Do not blindly read the ip address in ftrace_bug() 2021-06-16T09:59:45+00:00 Steven Rostedt (VMware) rostedt@goodmis.org 2021-06-08T01:39:08+00:00 7e4e824b109f1d41ccf223fbb0565d877d6223a2 commit 6c14133d2d3f768e0a35128faac8aa6ed4815051 upstream. It was reported that a bug on arm64 caused a bad ip address to be used for updating into a nop in ftrace_init(), but the error path (rightfully) returned -EINVAL and not -EFAULT, as the bug caused more than one error to occur. But because -EINVAL was returned, the ftrace_bug() tried to report what was at the location of the ip address, and read it directly. This caused the machine to panic, as the ip was not pointing to a valid memory address. Instead, read the ip address with copy_from_kernel_nofault() to safely access the memory, and if it faults, report that the address faulted, otherwise report what was in that location. Link: https://lore.kernel.org/lkml/20210607032329.28671-1-mark-pk.tsai@mediatek.com/ Cc: stable@vger.kernel.org Fixes: 05736a427f7e1 ("ftrace: warn on failure to disable mcount callers") Reported-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com> Tested-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 6c14133d2d3f768e0a35128faac8aa6ed4815051 upstream.

It was reported that a bug on arm64 caused a bad ip address to be used for
updating into a nop in ftrace_init(), but the error path (rightfully)
returned -EINVAL and not -EFAULT, as the bug caused more than one error to
occur. But because -EINVAL was returned, the ftrace_bug() tried to report
what was at the location of the ip address, and read it directly. This
caused the machine to panic, as the ip was not pointing to a valid memory
address.

Instead, read the ip address with copy_from_kernel_nofault() to safely
access the memory, and if it faults, report that the address faulted,
otherwise report what was in that location.

Link: https://lore.kernel.org/lkml/20210607032329.28671-1-mark-pk.tsai@mediatek.com/

Cc: stable@vger.kernel.org
Fixes: 05736a427f7e1 ("ftrace: warn on failure to disable mcount callers")
Reported-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Tested-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ftrace: Handle commands when closing set_ftrace_filter file 2021-05-11T12:04:01+00:00 Steven Rostedt (VMware) rostedt@goodmis.org 2021-05-05T14:38:24+00:00 0b641b25870f02e2423e494365fc5243cc1e2759 commit 8c9af478c06bb1ab1422f90d8ecbc53defd44bc3 upstream. # echo switch_mm:traceoff > /sys/kernel/tracing/set_ftrace_filter will cause switch_mm to stop tracing by the traceoff command. # echo -n switch_mm:traceoff > /sys/kernel/tracing/set_ftrace_filter does nothing. The reason is that the parsing in the write function only processes commands if it finished parsing (there is white space written after the command). That's to handle: write(fd, "switch_mm:", 10); write(fd, "traceoff", 8); cases, where the command is broken over multiple writes. The problem is if the file descriptor is closed, then the write call is not processed, and the command needs to be processed in the release code. The release code can handle matching of functions, but does not handle commands. Cc: stable@vger.kernel.org Fixes: eda1e32855656 ("tracing: handle broken names in ftrace filter") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 8c9af478c06bb1ab1422f90d8ecbc53defd44bc3 upstream.

 # echo switch_mm:traceoff > /sys/kernel/tracing/set_ftrace_filter

will cause switch_mm to stop tracing by the traceoff command.

 # echo -n switch_mm:traceoff > /sys/kernel/tracing/set_ftrace_filter

does nothing.

The reason is that the parsing in the write function only processes
commands if it finished parsing (there is white space written after the
command). That's to handle:

 write(fd, "switch_mm:", 10);
 write(fd, "traceoff", 8);

cases, where the command is broken over multiple writes.

The problem is if the file descriptor is closed, then the write call is
not processed, and the command needs to be processed in the release code.
The release code can handle matching of functions, but does not handle
commands.

Cc: stable@vger.kernel.org
Fixes: eda1e32855656 ("tracing: handle broken names in ftrace filter")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ftrace: Fix updating FTRACE_FL_TRAMP 2020-12-11T12:23:29+00:00 Naveen N. Rao naveen.n.rao@linux.vnet.ibm.com 2020-11-26T18:08:38+00:00 205740ca4a4d12c3732f914f6342770646b107e9 commit 4c75b0ff4e4bf7a45b5aef9639799719c28d0073 upstream. On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in ftrace_get_addr_new() followed by the below message: Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001) The set of steps leading to this involved: - modprobe ftrace-direct-too - enable_probe - modprobe ftrace-direct - rmmod ftrace-direct <-- trigger The problem turned out to be that we were not updating flags in the ftrace record properly. From the above message about the trampoline accounting being bad, it can be seen that the ftrace record still has FTRACE_FL_TRAMP set though ftrace-direct module is going away. This happens because we are checking if any ftrace_ops has the FTRACE_FL_TRAMP flag set _before_ updating the filter hash. The fix for this is to look for any _other_ ftrace_ops that also needs FTRACE_FL_TRAMP. Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com Cc: stable@vger.kernel.org Fixes: a124692b698b0 ("ftrace: Enable trampoline when rec count returns back to one") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 4c75b0ff4e4bf7a45b5aef9639799719c28d0073 upstream.

On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in
ftrace_get_addr_new() followed by the below message:
  Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)

The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger

The problem turned out to be that we were not updating flags in the
ftrace record properly. From the above message about the trampoline
accounting being bad, it can be seen that the ftrace record still has
FTRACE_FL_TRAMP set though ftrace-direct module is going away. This
happens because we are checking if any ftrace_ops has the
FTRACE_FL_TRAMP flag set _before_ updating the filter hash.

The fix for this is to look for any _other_ ftrace_ops that also needs
FTRACE_FL_TRAMP.

Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com

Cc: stable@vger.kernel.org
Fixes: a124692b698b0 ("ftrace: Enable trampoline when rec count returns back to one")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ftrace: Move RCU is watching check after recursion check 2020-10-07T06:01:25+00:00 Steven Rostedt (VMware) rostedt@goodmis.org 2020-09-29T16:40:31+00:00 c524a17312d4c4ab8df79928aa1214d5afd086a9 commit b40341fad6cc2daa195f8090fd3348f18fff640a upstream. The first thing that the ftrace function callback helper functions should do is to check for recursion. Peter Zijlstra found that when "rcu_is_watching()" had its notrace removed, it caused perf function tracing to crash. This is because the call of rcu_is_watching() is tested before function recursion is checked and and if it is traced, it will cause an infinite recursion loop. rcu_is_watching() should still stay notrace, but to prevent this should never had crashed in the first place. The recursion prevention must be the first thing done in callback functions. Link: https://lore.kernel.org/r/20200929112541.GM2628@hirez.programming.kicks-ass.net Cc: stable@vger.kernel.org Cc: Paul McKenney <paulmck@kernel.org> Fixes: c68c0fa293417 ("ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too") Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reported-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit b40341fad6cc2daa195f8090fd3348f18fff640a upstream.

The first thing that the ftrace function callback helper functions should do
is to check for recursion. Peter Zijlstra found that when
"rcu_is_watching()" had its notrace removed, it caused perf function tracing
to crash. This is because the call of rcu_is_watching() is tested before
function recursion is checked and and if it is traced, it will cause an
infinite recursion loop.

rcu_is_watching() should still stay notrace, but to prevent this should
never had crashed in the first place. The recursion prevention must be the
first thing done in callback functions.

Link: https://lore.kernel.org/r/20200929112541.GM2628@hirez.programming.kicks-ass.net

Cc: stable@vger.kernel.org
Cc: Paul McKenney <paulmck@kernel.org>
Fixes: c68c0fa293417 ("ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too")
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tracing: Use trace_sched_process_free() instead of exit() for pid tracing 2020-08-21T11:05:27+00:00 Steven Rostedt (VMware) rostedt@goodmis.org 2020-08-05T00:00:02+00:00 9aab8b2b0f8f77c0a14548c90ec88ede1d5fe8d7 commit afcab636657421f7ebfa0783a91f90256bba0091 upstream. On exit, if a process is preempted after the trace_sched_process_exit() tracepoint but before the process is done exiting, then when it gets scheduled in, the function tracers will not filter it properly against the function tracing pid filters. That is because the function tracing pid filters hooks to the sched_process_exit() tracepoint to remove the exiting task's pid from the filter list. Because the filtering happens at the sched_switch tracepoint, when the exiting task schedules back in to finish up the exit, it will no longer be in the function pid filtering tables. This was noticeable in the notrace self tests on a preemptable kernel, as the tests would fail as it exits and preempted after being taken off the notrace filter table and on scheduling back in it would not be in the notrace list, and then the ending of the exit function would trace. The test detected this and would fail. Cc: stable@vger.kernel.org Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 1e10486ffee0a ("ftrace: Add 'function-fork' trace option") Fixes: c37775d57830a ("tracing: Add infrastructure to allow set_event_pid to follow children" Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit afcab636657421f7ebfa0783a91f90256bba0091 upstream.

On exit, if a process is preempted after the trace_sched_process_exit()
tracepoint but before the process is done exiting, then when it gets
scheduled in, the function tracers will not filter it properly against the
function tracing pid filters.

That is because the function tracing pid filters hooks to the
sched_process_exit() tracepoint to remove the exiting task's pid from the
filter list. Because the filtering happens at the sched_switch tracepoint,
when the exiting task schedules back in to finish up the exit, it will no
longer be in the function pid filtering tables.

This was noticeable in the notrace self tests on a preemptable kernel, as
the tests would fail as it exits and preempted after being taken off the
notrace filter table and on scheduling back in it would not be in the
notrace list, and then the ending of the exit function would trace. The test
detected this and would fail.

Cc: stable@vger.kernel.org
Cc: Namhyung Kim <namhyung@kernel.org>
Fixes: 1e10486ffee0a ("ftrace: Add 'function-fork' trace option")
Fixes: c37775d57830a ("tracing: Add infrastructure to allow set_event_pid to follow children"
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ftrace: Setup correct FTRACE_FL_REGS flags for module 2020-08-21T11:05:27+00:00 Chengming Zhou zhouchengming@bytedance.com 2020-07-28T18:05:53+00:00 3a1208574658b6126a566f296344a3472b8dfc08 commit 8a224ffb3f52b0027f6b7279854c71a31c48fc97 upstream. When module loaded and enabled, we will use __ftrace_replace_code for module if any ftrace_ops referenced it found. But we will get wrong ftrace_addr for module rec in ftrace_get_addr_new, because rec->flags has not been setup correctly. It can cause the callback function of a ftrace_ops has FTRACE_OPS_FL_SAVE_REGS to be called with pt_regs set to NULL. So setup correct FTRACE_FL_REGS flags for rec when we call referenced_filters to find ftrace_ops references it. Link: https://lkml.kernel.org/r/20200728180554.65203-1-zhouchengming@bytedance.com Cc: stable@vger.kernel.org Fixes: 8c4f3c3fa9681 ("ftrace: Check module functions being traced on reload") Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com> Signed-off-by: Muchun Song <songmuchun@bytedance.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 8a224ffb3f52b0027f6b7279854c71a31c48fc97 upstream.

When module loaded and enabled, we will use __ftrace_replace_code
for module if any ftrace_ops referenced it found. But we will get
wrong ftrace_addr for module rec in ftrace_get_addr_new, because
rec->flags has not been setup correctly. It can cause the callback
function of a ftrace_ops has FTRACE_OPS_FL_SAVE_REGS to be called
with pt_regs set to NULL.
So setup correct FTRACE_FL_REGS flags for rec when we call
referenced_filters to find ftrace_ops references it.

Link: https://lkml.kernel.org/r/20200728180554.65203-1-zhouchengming@bytedance.com

Cc: stable@vger.kernel.org
Fixes: 8c4f3c3fa9681 ("ftrace: Check module functions being traced on reload")
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ftrace: fpid_next() should increase position index 2020-02-24T07:36:59+00:00 Vasily Averin vvs@virtuozzo.com 2020-01-24T07:02:56+00:00 e349287276c2713423b9ade5516208da17f6c1f4 [ Upstream commit e4075e8bdffd93a9b6d6e1d52fabedceeca5a91b ] if seq_file .next fuction does not change position index, read after some lseek can generate unexpected output. Without patch: # dd bs=4 skip=1 if=/sys/kernel/tracing/set_ftrace_pid dd: /sys/kernel/tracing/set_ftrace_pid: cannot skip to specified offset id no pid 2+1 records in 2+1 records out 10 bytes copied, 0.000213285 s, 46.9 kB/s Notice the "id" followed by "no pid". With the patch: # dd bs=4 skip=1 if=/sys/kernel/tracing/set_ftrace_pid dd: /sys/kernel/tracing/set_ftrace_pid: cannot skip to specified offset id 0+1 records in 0+1 records out 3 bytes copied, 0.000202112 s, 14.8 kB/s Notice that it only prints "id" and not the "no pid" afterward. Link: http://lkml.kernel.org/r/4f87c6ad-f114-30bb-8506-c32274ce2992@virtuozzo.com https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit e4075e8bdffd93a9b6d6e1d52fabedceeca5a91b ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

Without patch:
 # dd bs=4 skip=1 if=/sys/kernel/tracing/set_ftrace_pid
 dd: /sys/kernel/tracing/set_ftrace_pid: cannot skip to specified offset
 id
 no pid
 2+1 records in
 2+1 records out
 10 bytes copied, 0.000213285 s, 46.9 kB/s

Notice the "id" followed by "no pid".

With the patch:
 # dd bs=4 skip=1 if=/sys/kernel/tracing/set_ftrace_pid
 dd: /sys/kernel/tracing/set_ftrace_pid: cannot skip to specified offset
 id
 0+1 records in
 0+1 records out
 3 bytes copied, 0.000202112 s, 14.8 kB/s

Notice that it only prints "id" and not the "no pid" afterward.

Link: http://lkml.kernel.org/r/4f87c6ad-f114-30bb-8506-c32274ce2992@virtuozzo.com

https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ftrace: Protect ftrace_graph_hash with ftrace_sync 2020-02-11T12:35:28+00:00 Steven Rostedt (VMware) rostedt@goodmis.org 2020-02-05T14:20:32+00:00 c8e9dafe668d9c50e1b1287ac2375497d747f367 [ Upstream commit 54a16ff6f2e50775145b210bcd94d62c3c2af117 ] As function_graph tracer can run when RCU is not "watching", it can not be protected by synchronize_rcu() it requires running a task on each CPU before it can be freed. Calling schedule_on_each_cpu(ftrace_sync) needs to be used. Link: https://lore.kernel.org/r/20200205131110.GT2935@paulmck-ThinkPad-P72 Cc: stable@vger.kernel.org Fixes: b9b0c831bed26 ("ftrace: Convert graph filter to use hash tables") Reported-by: "Paul E. McKenney" <paulmck@kernel.org> Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 54a16ff6f2e50775145b210bcd94d62c3c2af117 ]

As function_graph tracer can run when RCU is not "watching", it can not be
protected by synchronize_rcu() it requires running a task on each CPU before
it can be freed. Calling schedule_on_each_cpu(ftrace_sync) needs to be used.

Link: https://lore.kernel.org/r/20200205131110.GT2935@paulmck-ThinkPad-P72

Cc: stable@vger.kernel.org
Fixes: b9b0c831bed26 ("ftrace: Convert graph filter to use hash tables")
Reported-by: "Paul E. McKenney" <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
tracing: Annotate ftrace_graph_notrace_hash pointer with __rcu 2020-02-11T12:35:27+00:00 Amol Grover frextrite@gmail.com 2020-02-05T05:57:02+00:00 c9dc142b39a89e4bb29beaa92740413863fadca2 [ Upstream commit fd0e6852c407dd9aefc594f54ddcc21d84803d3b ] Fix following instances of sparse error kernel/trace/ftrace.c:5667:29: error: incompatible types in comparison kernel/trace/ftrace.c:5813:21: error: incompatible types in comparison kernel/trace/ftrace.c:5868:36: error: incompatible types in comparison kernel/trace/ftrace.c:5870:25: error: incompatible types in comparison Use rcu_dereference_protected to dereference the newly annotated pointer. Link: http://lkml.kernel.org/r/20200205055701.30195-1-frextrite@gmail.com Signed-off-by: Amol Grover <frextrite@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit fd0e6852c407dd9aefc594f54ddcc21d84803d3b ]

Fix following instances of sparse error
kernel/trace/ftrace.c:5667:29: error: incompatible types in comparison
kernel/trace/ftrace.c:5813:21: error: incompatible types in comparison
kernel/trace/ftrace.c:5868:36: error: incompatible types in comparison
kernel/trace/ftrace.c:5870:25: error: incompatible types in comparison

Use rcu_dereference_protected to dereference the newly annotated pointer.

Link: http://lkml.kernel.org/r/20200205055701.30195-1-frextrite@gmail.com

Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>