linux-stable.git/kernel/power/suspend.c, branch linux-5.15.y

PM: suspend: Set mem_sleep_current during kernel command line setup

2024-04-10T14:18:36+00:00

[ Upstream commit 9bc4ffd32ef8943f5c5a42c9637cfd04771d021b ]

psci_init_system_suspend() invokes suspend_set_ops() very early during
bootup even before kernel command line for mem_sleep_default is setup.
This leads to kernel command line mem_sleep_default=s2idle not working
as mem_sleep_current gets changed to deep via suspend_set_ops() and never
changes back to s2idle.

Set mem_sleep_current along with mem_sleep_default during kernel command
line setup as default suspend mode.

Fixes: faf7ec4a92c0 ("drivers: firmware: psci: add system suspend support")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Maulik Shah 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin

PM: s2idle: ACPI: Fix wakeup interrupts handling

2022-02-16T11:56:19+00:00

commit cb1f65c1e1424a4b5e4a86da8aa3b8fd8459c8ec upstream.

After commit e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed.  Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.

The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop().  However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.

To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup.  Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one.  [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]

Fixes: e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE")
Cc: 5.4+  # 5.4+
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

PM: sleep: s2idle: Replace deprecated CPU-hotplug functions

2021-08-04T18:18:13+00:00

The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().

Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.

Signed-off-by: Sebastian Andrzej Siewior 
Signed-off-by: Rafael J. Wysocki

PM / suspend: fix kernel-doc markup

2020-11-23T17:24:53+00:00

Add parameter explanation to fix kernel-doc marks:

kernel/power/suspend.c:233: warning: Function parameter or member
'state' not described in 'suspend_valid_only_mem'
kernel/power/suspend.c:344: warning: Function parameter or member
'state' not described in 'suspend_prepare'

Signed-off-by: Alex Shi 
[ rjw: Change the proposed parameter descriptions. ]
Signed-off-by: Rafael J. Wysocki

notifier: Fix broken error handling pattern

2020-09-01T07:58:03+00:00

The current notifiers have the following error handling pattern all
over the place:

	int err, nr;

	err = __foo_notifier_call_chain(&chain, val_up, v, -1, &nr);
	if (err & NOTIFIER_STOP_MASK)
		__foo_notifier_call_chain(&chain, val_down, v, nr-1, NULL)

And aside from the endless repetition thereof, it is broken. Consider
blocking notifiers; both calls take and drop the rwsem, this means
that the notifier list can change in between the two calls, making @nr
meaningless.

Fix this by replacing all the __foo_notifier_call_chain() functions
with foo_notifier_call_chain_robust() that embeds the above pattern,
but ensures it is inside a single lock region.

Note: I switched atomic_notifier_call_chain_robust() to use
      the spinlock, since RCU cannot provide the guarantee
      required for the recovery.

Note: software_resume() error handling was broken afaict.

Signed-off-by: Peter Zijlstra (Intel) 
Signed-off-by: Ingo Molnar 
Acked-by: Rafael J. Wysocki 
Link: https://lore.kernel.org/r/20200818135804.325626653@infradead.org

ACPI: PM: s2idle: Avoid possible race related to the EC GPE

2020-02-11T09:11:02+00:00

It is theoretically possible for the ACPI EC GPE to be set after the
s2idle_ops->wake() called from s2idle_loop() has returned and before
the subsequent pm_wakeup_pending() check is carried out.  If that
happens, the resulting wakeup event will cause the system to resume
even though it may be a spurious one.

To avoid that race, first make the ->wake() callback in struct
platform_s2idle_ops return a bool value indicating whether or not
to let the system resume and rearrange s2idle_loop() to use that
value instad of the direct pm_wakeup_pending() call if ->wake() is
present.

Next, rework acpi_s2idle_wake() to process EC events and check
pm_wakeup_pending() before re-arming the SCI for system wakeup
to prevent it from triggering prematurely and add comments to
that function to explain the rationale for the new code flow.

Fixes: 56b991849009 ("PM: sleep: Simplify suspend-to-idle control flow")
Cc: 5.4+  # 5.4+
Signed-off-by: Rafael J. Wysocki

PM: suspend: Add sysfs attribute to control the "sync on suspend" behavior

2020-01-16T20:47:03+00:00

The sysfs attribute `/sys/power/sync_on_suspend` controls, whether or not
filesystems are synced by the kernel before system suspend.

Congruously, the behaviour of build-time switch CONFIG_SUSPEND_SKIP_SYNC
is slightly changed: It now defines the run-tim default for the new sysfs
attribute `/sys/power/sync_on_suspend`.

The run-time attribute is added because the existing corresponding
build-time Kconfig flag for (`CONFIG_SUSPEND_SKIP_SYNC`) is not flexible
enough. E.g. Linux distributions that provide pre-compiled kernels
usually want to stick with the default (sync filesystems before suspend)
but under special conditions this needs to be changed.

One example for such a special condition is user-space handling of
suspending block devices (e.g. using `cryptsetup luksSuspend` or `dmsetup
suspend`) before system suspend. The Kernel trying to sync filesystems
after the underlying block device already got suspended obviously leads
to dead-locks. Be aware that you have to take care of the filesystem sync
yourself before suspending the system in those scenarios.

Signed-off-by: Jonas Meurer 
Signed-off-by: Rafael J. Wysocki

PM: suspend: Fix platform_suspend_prepare_noirq()

2019-08-10T11:18:06+00:00

After commit ac9eafbe930a ("ACPI: PM: s2idle: Execute LPS0 _DSM
functions with suspended devices"), a NULL pointer may be dereferenced
if suspend-to-idle is attempted on a platform without "traditional"
suspend support due to invalid fall-through in
platform_suspend_prepare_noirq().

Fix that and while at it add missing braces in platform_resume_noirq().

Fixes: ac9eafbe930a ("ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices")
Reported-by: Marek Szyprowski 
Signed-off-by: Rafael J. Wysocki

ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices

2019-08-08T09:26:01+00:00

According to Section 3.5 of the "Intel Low Power S0 Idle" document [1],
Function 5 of the LPS0 _DSM is expected to be invoked when the system
configuration matches the criteria for entering the target low-power
state of the platform.  In particular, this means that all devices
should be suspended and in low-power states already when that function
is invoked.

This is not the case currently, however, because Function 5 of the
LPS0 _DSM is invoked by it before the "noirq" phase of device suspend,
which means that some devices may not have been put into low-power
states yet at that point.  That is a consequence of the previous
design of the suspend-to-idle flow that allowed the "noirq" phase of
device suspend and the "noirq" phase of device resume to be carried
out for multiple times while "suspended" (if any spurious wakeup
events were detected) and the point of the LPS0 _DSM Function 5
invocation was chosen so as to call it (and LPS0 _DSM Function 6
analogously) once per suspend-resume cycle (regardless of how many
times the "noirq" phases of device suspend and resume were carried
out while "suspended").

Now that the suspend-to-idle flow has been redesigned to carry out
the "noirq" phases of device suspend and resume once in each cycle,
the code can be reordered to follow the specification that it is
based on more closely.

For this purpose, add ->prepare_late and ->restore_early platform
callbacks for suspend-to-idle, to be executed, respectively, after
the "noirq" phase of suspending devices and before the "noirq"
phase of resuming them and make ACPI use them for the invocation
of LPS0 _DSM functions as appropriate.

While at it, move the LPS0 entry requirements check to be made
before invoking Functions 3 and 5 of the LPS0 _DSM (also once
per cycle) as follows from the specification [1].

Link: https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf # [1]
Signed-off-by: Rafael J. Wysocki 
Tested-by: Kai-Heng Feng

PM: sleep: Integrate suspend-to-idle with generig suspend flow

2019-07-23T07:46:50+00:00

After previous changes the suspend-to-idle code flow can be
integrated more tightly with the generic system suspend code flow
by making suspend_enter() call s2idle_loop() later and removing
the direct invocations of dpm_noirq_begin(),
dpm_noirq_suspend_devices(), dpm_noirq_end(), and
dpm_noirq_resume_devices() from the latter, so do that.

This change is not expected to alter functionality.

Signed-off-by: Rafael J. Wysocki 
Acked-by: Thomas Gleixner