Pull x96 apic updates from Thomas Gleixner:
"Updates for the x86 APIC interrupt handling and APIC timer:
- Fix a long standing issue with spurious interrupts which was caused
by the big vector management rework a few years ago. Robert Hodaszi
provided finally enough debug data and an excellent initial failure
analysis which allowed to understand the underlying issues.
This contains a change to the core interrupt management code which
is required to handle this correctly for the APIC/IO_APIC. The core
changes are NOOPs for most architectures except ARM64. ARM64 is not
impacted by the change as confirmed by Marc Zyngier.
- Newer systems allow to disable the PIT clock for power saving
causing panic in the timer interrupt delivery check of the IO/APIC
when the HPET timer is not enabled either. While the clock could be
turned on this would cause an endless whack a mole game to chase
the proper register in each affected chipset.
These systems provide the relevant frequencies for TSC, CPU and the
local APIC timer via CPUID and/or MSRs, which allows to avoid the
PIT/HPET based calibration. As the calibration code is the only
usage of the legacy timers on modern systems and is skipped anyway
when the frequencies are known already, there is no point in
setting up the PIT and actually checking for the interrupt delivery
via IO/APIC.
To achieve this on a wide variety of platforms, the CPUID/MSR based
frequency readout has been made more robust, which also allowed to
remove quite some workarounds which turned out to be not longer
required. Thanks to Daniel Drake for analysis, patches and
verification"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Seperate unused system vectors from spurious entry again
x86/irq: Handle spurious interrupt after shutdown gracefully
x86/ioapic: Implement irq_get_irqchip_state() callback
genirq: Add optional hardware synchronization for shutdown
genirq: Fix misleading synchronize_irq() documentation
genirq: Delay deactivation in free_irq()
x86/timer: Skip PIT initialization on modern chipsets
x86/apic: Use non-atomic operations when possible
x86/apic: Make apic_bsp_setup() static
x86/tsc: Set LAPIC timer period to crystal clock frequency
x86/apic: Rename 'lapic_timer_frequency' to 'lapic_timer_period'
x86/tsc: Use CPUID.0x16 to calculate missing crystal frequency
The NMI handlers handle_percpu_devid_fasteoi_nmi() and handle_fasteoi_nmi()
do not update the interrupt counts. Due to that the NMI interrupt count
does not show up correctly in /proc/interrupts.
Add the statistics and treat the NMI handlers in the same way as per cpu
interrupts and prevent them from updating irq_desc::tot_count as this might
be corrupted due to concurrency.
[ tglx: Massaged changelog ]
Fixes: 2dcf1fbcad35 ("genirq: Provide NMI handlers")
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1562313336-11888-1-git-send-email-sthotton@marvell.com
When interrupts are shutdown, they are immediately deactivated in the
irqdomain hierarchy. While this looks obviously correct there is a subtle
issue:
There might be an interrupt in flight when free_irq() is invoking the
shutdown. This is properly handled at the irq descriptor / primary handler
level, but the deactivation might completely disable resources which are
required to acknowledge the interrupt.
Split the shutdown code and deactivate the interrupt after synchronization
in free_irq(). Fixup all other usage sites where this is not an issue to
invoke the combined shutdown_and_deactivate() function instead.
This still might be an issue if the interrupt in flight servicing is
delayed on a remote CPU beyond the invocation of synchronize_irq(), but
that cannot be handled at that level and needs to be handled in the
synchronize_irq() context.
Fixes: f8264e34965a ("irqdomain: Introduce new interfaces to support hierarchy irqdomains")
Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.098196390@linutronix.de
Introduce irq_chip_{request,release}_resource_parent() apis so
that these can be used in hierarchical irqchips.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If a child irqchip calls irq_chip_set_wake_parent() but its parent irqchip
has the IRQCHIP_SKIP_SET_WAKE flag set an error is returned.
This is inconsistent behaviour vs. set_irq_wake_real() which returns 0 when
the irqchip has the IRQCHIP_SKIP_SET_WAKE flag set. It doesn't attempt to
walk the chain of parents and set irq wake on any chips that don't have the
flag set either. If the intent is to call the .irq_set_wake() callback of
the parent irqchip, then we expect irqchip implementations to omit the
IRQCHIP_SKIP_SET_WAKE flag and implement an .irq_set_wake() function that
calls irq_chip_set_wake_parent().
The problem has been observed on a Qualcomm sdm845 device where set wake
fails on any GPIO interrupts after applying work in progress wakeup irq
patches to the GPIO driver. The chain of chips looks like this:
QCOM GPIO -> QCOM PDC (SKIP) -> ARM GIC (SKIP)
The GPIO controllers parent is the QCOM PDC irqchip which in turn has ARM
GIC as parent. The QCOM PDC irqchip has the IRQCHIP_SKIP_SET_WAKE flag
set, and so does the grandparent ARM GIC.
The GPIO driver doesn't know if the parent needs to set wake or not, so it
unconditionally calls irq_chip_set_wake_parent() causing this function to
return a failure because the parent irqchip (PDC) doesn't have the
.irq_set_wake() callback set. Returning 0 instead makes everything work and
irqs from the GPIO controller can be configured for wakeup.
Make it consistent by returning 0 (success) from irq_chip_set_wake_parent()
when a parent chip has IRQCHIP_SKIP_SET_WAKE set.
[ tglx: Massaged changelog ]
Fixes: 08b55e2a9208e ("genirq: Add irqchip_set_wake_parent")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190325181026.247796-1-swboyd@chromium.org
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
Pull irqchip updates from Marc Zyngier - Core pseudo-NMI handling code - Allow the default irq domain to be retrieved - A new interrupt controller for the Loongson LS1X platform - Affinity support for the SiFive PLIC - Better support for the iMX irqsteer driver - NUMA aware memory allocations for GICv3 - A handful of other fixes (i8259, GICv3, PLIC)
The hierarchical irqchip never before ran into a situation where the parent is not "simple", i.e. does not implement .irq_ack() and .irq_mask() like most, but the qcom-pm8xxx.c happens to implement only .irq_mask_ack(). Since we want to make ssbi-gpio a hierarchical child of this irqchip, it must *also* only implement .irq_mask_ack() and call down to the parent, and for this we of course need irq_chip_mask_ack_parent(). Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Waiman reported that on large systems with a large amount of interrupts the readout of /proc/stat takes a long time to sum up the interrupt statistics. In principle this is not a problem. but for unknown reasons some enterprise quality software reads /proc/stat with a high frequency. The reason for this is that interrupt statistics are accounted per cpu. So the /proc/stat logic has to sum up the interrupt stats for each interrupt. This can be largely avoided for interrupts which are not marked as 'PER_CPU' interrupts by simply adding a per interrupt summation counter which is incremented along with the per interrupt per cpu counter. The PER_CPU interrupts need to avoid that and use only per cpu accounting because they share the interrupt number and the interrupt descriptor and concurrent updates would conflict or require unwanted synchronization. Reported-by: Waiman Long <longman@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Waiman Long <longman@redhat.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Davidlohr Bueso <dbueso@suse.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Kees Cook <keescook@chromium.org> Cc: linux-fsdevel@vger.kernel.org Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Miklos Szeredi <miklos@szeredi.hu> Cc: Daniel Colascione <dancol@google.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Randy Dunlap <rdunlap@infradead.org> Link: https://lkml.kernel.org/r/20190208135020.925487496@linutronix.de 8<------------- v2: Undo the unintentional layout change of struct irq_desc. include/linux/irqdesc.h | 1 + kernel/irq/chip.c | 12 ++++++++++-- kernel/irq/internals.h | 8 +++++++- kernel/irq/irqdesc.c | 7 ++++++- 4 files changed, 24 insertions(+), 4 deletions(-)