wiphy names were recently limited to 128 bytes by commit a7cfebcb7594
("cfg80211: limit wiphy names to 128 bytes").  As it turns out though,
this isn't sufficient because dev_vprintk_emit() needs the syslog header
string "SUBSYSTEM=ieee80211\0DEVICE=+ieee80211:$devname" to fit into 128
bytes.  This triggered the "device/subsystem name too long" WARN when
the device name was >= 90 bytes.  As before, this was reproduced by
syzbot by sending an HWSIM_CMD_NEW_RADIO command to the MAC80211_HWSIM
generic netlink family.

Fix it by further limiting wiphy names to 64 bytes.

Reported-by: syzbot+e64565577af34b3768dc@syzkaller.appspotmail.com
Fixes: a7cfebcb7594 ("cfg80211: limit wiphy names to 128 bytes")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's currently no limit on wiphy names, other than netlink
message size and memory limitations, but that causes issues when,
for example, the wiphy name is used in a uevent, e.g. in rfkill
where we use the same name for the rfkill instance, and then the
buffer there is "only" 2k for the environment variables.

This was reported by syzkaller, which used a 4k name.

Limit the name to something reasonable, I randomly picked 128.

Reported-by: syzbot+230d9e642a85d3fec29c@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME.
Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME.
Userspace should also provide the destination address and the protocol
type to use when sending the frame.  This is used to implement TX of
Pre-authentication frames.  If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is
specified, then the driver will be asked not to encrypt the outgoing
frame.

A new EXT_FEATURE flag is introduced so that nl80211 code can check
whether a given wiphy has capability to pass EAPoL frames over nl80211.

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This commit also adds cfg80211_rx_control_port function.  This is used
to generate a CMD_CONTROL_PORT_FRAME event out to userspace.  The
conn_owner_nlportid is used as the unicast destination.  This means that
userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port
over nl80211 routing is requested in NL80211_CMD_CONNECT,
NL80211_CMD_ASSOCIATE, NL80211_CMD_START_AP or IBSS/mesh join.

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix return value of cfg80211_rx_control_port()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add wiphy EXT_FEATURE flag to indicate that HW or driver does
all DFS actions by itself.
User-space functionality already implemented in hostapd using
vendor-specific (QCA) OUI to advertise DFS offload support.
Need to introduce generic flag to inform about DFS offload support.
For devices with DFS_OFFLOAD flag set user-space will no longer
need to issue CAC or do any actions in response to
"radar detected" events. HW will do everything by itself and send
events to user-space to indicate that CAC was started/finished, etc.

Signed-off-by: Dmitrii Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

CAC_STARTED event is needed for DFS offload feature and
should be generated by driver/HW if DFS_OFFLOAD is enabled.

Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>