linux-stable.git/include/linux, branch v4.6.2

mm: use phys_addr_t for reserve_bootmem_region() arguments

2016-06-08T01:23:38+00:00

commit 4b50bcc7eda4d3cc9e3f2a0aa60e590fedf728c5 upstream.

Since commit 92923ca3aace ("mm: meminit: only set page reserved in the
memblock region") the reserved bit is set on reserved memblock regions.
However start and end address are passed as unsigned long.  This is only
32bit on i386, so it can end up marking the wrong pages reserved for
ranges at 4GB and above.

This was observed on a 32bit Xen dom0 which was booted with initial
memory set to a value below 4G but allowing to balloon in memory
(dom0_mem=1024M for example).  This would define a reserved bootmem
region for the additional memory (for example on a 8GB system there was
a reverved region covering the 4GB-8GB range).  But since the addresses
were passed on as unsigned long, this was actually marking all pages
from 0 to 4GB as reserved.

Fixes: 92923ca3aacef63 ("mm: meminit: only set page reserved in the memblock region")
Link: http://lkml.kernel.org/r/1463491221-10573-1-git-send-email-stefan.bader@canonical.com
Signed-off-by: Stefan Bader 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds 
Signed-off-by: Greg Kroah-Hartman

SIGNAL: Move generic copy_siginfo() to signal.h

2016-06-01T19:18:05+00:00

commit ca9eb49aa9562eaadf3cea071ec7018ad6800425 upstream.

The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.

It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.

Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.

Signed-off-by: James Hogan 
Cc: Arnd Bergmann 
Cc: Ralf Baechle 
Cc: Petr Malat 
Cc: Tony Luck 
Cc: Fenghua Yu 
Cc: Christopher Ferris 
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle 
Signed-off-by: Greg Kroah-Hartman

Fix OpenSSH pty regression on close

2016-06-01T19:18:03+00:00

commit 0f40fbbcc34e093255a2b2d70b6b0fb48c3f39aa upstream.

OpenSSH expects the (non-blocking) read() of pty master to return
EAGAIN only if it has received all of the slave-side output after
it has received SIGCHLD. This used to work on pre-3.12 kernels.

This fix effectively forces non-blocking read() and poll() to
block for parallel i/o to complete for all ttys. It also unwinds
these changes:

1) f8747d4a466ab2cafe56112c51b3379f9fdb7a12
   tty: Fix pty master read() after slave closes

2) 52bce7f8d4fc633c9a9d0646eef58ba6ae9a3b73
   pty, n_tty: Simplify input processing on final close

3) 1a48632ffed61352a7810ce089dc5a8bcd505a60
   pty: Fix input race when closing

Inspired by analysis and patch from Marc Aurele La France 

Reported-by: Volth 
Reported-by: Marc Aurele La France 
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492
Signed-off-by: Brian Bloniarz 
Reviewed-by: Peter Hurley 
Signed-off-by: Greg Kroah-Hartman

usb: core: hub: hub_port_init lock controller instead of bus

2016-06-01T19:18:02+00:00

commit feb26ac31a2a5cb88d86680d9a94916a6343e9e6 upstream.

The XHCI controller presents two USB buses to the system - one for USB2
and one for USB3. The hub init code (hub_port_init) is reentrant but
only locks one bus per thread, leading to a race condition failure when
two threads attempt to simultaneously initialise a USB2 and USB3 device:

[    8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[   13.183701] usb 3-3: device descriptor read/all, error -110

On a test system this failure occurred on 6% of all boots.

The call traces at the point of failure are:

Call Trace:
 [] schedule+0x37/0x90
 [] usb_kill_urb+0x8d/0xd0
 [] ? wake_up_atomic_t+0x30/0x30
 [] usb_start_wait_urb+0xbe/0x150
 [] usb_control_msg+0xbc/0xf0
 [] hub_port_init+0x51e/0xb70
 [] hub_event+0x817/0x1570
 [] process_one_work+0x1ff/0x620
 [] ? process_one_work+0x15f/0x620
 [] worker_thread+0x64/0x4b0
 [] ? rescuer_thread+0x390/0x390
 [] kthread+0x105/0x120
 [] ? kthread_create_on_node+0x200/0x200
 [] ret_from_fork+0x3f/0x70
 [] ? kthread_create_on_node+0x200/0x200

Call Trace:
 [] xhci_setup_device+0x53d/0xa40
 [] xhci_address_device+0xe/0x10
 [] hub_port_init+0x1bf/0xb70
 [] ? trace_hardirqs_on+0xd/0x10
 [] hub_event+0x817/0x1570
 [] process_one_work+0x1ff/0x620
 [] ? process_one_work+0x15f/0x620
 [] worker_thread+0x64/0x4b0
 [] ? rescuer_thread+0x390/0x390
 [] kthread+0x105/0x120
 [] ? kthread_create_on_node+0x200/0x200
 [] ret_from_fork+0x3f/0x70
 [] ? kthread_create_on_node+0x200/0x200

Which results from the two call chains:

hub_port_init
 usb_get_device_descriptor
  usb_get_descriptor
   usb_control_msg
    usb_internal_control_msg
     usb_start_wait_urb
      usb_submit_urb / wait_for_completion_timeout / usb_kill_urb

hub_port_init
 hub_set_address
  xhci_address_device
   xhci_setup_device

Mathias Nyman explains the current behaviour violates the XHCI spec:

 hub_port_reset() will end up moving the corresponding xhci device slot
 to default state.

 As hub_port_reset() is called several times in hub_port_init() it
 sounds reasonable that we could end up with two threads having their
 xhci device slots in default state at the same time, which according to
 xhci 4.5.3 specs still is a big no no:

 "Note: Software shall not transition more than one Device Slot to the
  Default State at a time"

 So both threads fail at their next task after this.
 One fails to read the descriptor, and the other fails addressing the
 device.

Fix this in hub_port_init by locking the USB controller (instead of an
individual bus) to prevent simultaneous initialisation of both buses.

Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.org/lkml/2016/2/8/312
Link: https://lkml.org/lkml/2016/2/4/748
Signed-off-by: Chris Bainbridge 
Acked-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

USB: leave LPM alone if possible when binding/unbinding interface drivers

2016-06-01T19:18:02+00:00

commit 6fb650d43da3e7054984dc548eaa88765a94d49f upstream.

When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward.  The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters.  This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.

However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary.  The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.

It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs.  Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.

And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.

Signed-off-by: Alan Stern 
Tested-by: Matthew Giassa 
CC: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

can: fix handling of unmodifiable configuration options

2016-06-01T19:17:59+00:00

commit bb208f144cf3f59d8f89a09a80efd04389718907 upstream.

As described in 'can: m_can: tag current CAN FD controllers as non-ISO'
(6cfda7fbebe) it is possible to define fixed configuration options by
setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'.
This leads to the incovenience that the fixed configuration bits can not be
passed by netlink even when they have the correct values (e.g. non-ISO, FD).

This patch fixes that issue and not only allows fixed set bit values to be set
again but now requires(!) to provide these fixed values at configuration time.
A valid CAN FD configuration consists of a nominal/arbitration bittiming, a
data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now
enforced by a new can_validate() function. This fix additionally removed the
inconsistency that was prohibiting the support of 'CANFD-only' controller
drivers, like the RCar CAN FD.

For this reason a new helper can_set_static_ctrlmode() has been introduced to
provide a proper interface to handle static enabled CAN controller options.

Reported-by: Ramesh Shanmugasundaram 
Signed-off-by: Oliver Hartkopp 
Reviewed-by: Ramesh Shanmugasundaram  
Signed-off-by: Marc Kleine-Budde 
Signed-off-by: Greg Kroah-Hartman

fscrypto/f2fs: allow fs-specific key prefix for fs encryption

2016-06-01T19:17:59+00:00

commit b5a7aef1ef436ec005fef0efe31a676ec5f4ab31 upstream.

This patch allows fscrypto to handle a second key prefix given by filesystem.
The main reason is to provide backward compatibility, since previously f2fs
used "f2fs:" as a crypto prefix instead of "fscrypt:".
Later, ext4 should also provide key_prefix() to give "ext4:".

One concern decribed by Ted would be kinda double check overhead of prefixes.
In x86, for example, validate_user_key consumes 8 ms after boot-up, which turns
out derive_key_aes() consumed most of the time to load specific crypto module.
After such the cold miss, it shows almost zero latencies, which treats as a
negligible overhead.
Note that request_key() detects wrong prefix in prior to derive_key_aes() even.

Cc: Ted Tso 
Signed-off-by: Jaegeuk Kim 
Signed-off-by: Greg Kroah-Hartman

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs

2016-05-14T18:59:43+00:00

Pull vfs fixes from Al Viro:
 "Overlayfs fixes from Miklos, assorted fixes from me.

  Stable fodder of varying severity, all sat in -next for a while"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ovl: ignore permissions on underlying lookup
  vfs: add lookup_hash() helper
  vfs: rename: check backing inode being equal
  vfs: add vfs_select_inode() helper
  get_rock_ridge_filename(): handle malformed NM entries
  ecryptfs: fix handling of directory opening
  atomic_open(): fix the handling of create_error
  fix the copy vs. map logics in blk_rq_map_user_iov()
  do_splice_to(): cap the size before passing to ->splice_read()

Merge branch 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup

2016-05-13T23:26:46+00:00

Pull cgroup fixes from Tejun Heo:
 "During v4.6-rc1 cgroup namespace support was merged.  There is an
  issue where it's impossible to tell whether a given cgroup mount point
  is bind mounted or namespaced.  Serge has been working on the issue
  but it took longer than expected to resolve, so the late pull request.

  Given that it's a completely new feature and the patches don't touch
  anything else, the risk seems acceptable.  However, if this is too
  late, an alternative is plugging new cgroup ns creation for v4.6 and
  retrying for v4.7"

* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix compile warning
  kernfs: kernfs_sop_show_path: don't return 0 after seq_dentry call
  cgroup, kernfs: make mountinfo show properly scoped path for cgroup namespaces
  kernfs_path_from_node_locked: don't overwrite nlen

Merge tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

2016-05-13T16:46:00+00:00

Pull regulator fixes from Mark Brown:
 "A small collection of driver specific fixes for the regulator
  subsysetem:

   - Fix handling of probe deferral for GPIO regulators

   - Fix a typo in the module alias for DA9053

   - Fix the definition of BUCK9 in the S2MPS11 driver.  This change
     looks larger than it is because an irregularity in the hardware
     means that the macro used to define bucks 6-10 needs duplicating
     and tweaking to have a separate macro for 9

   - Fix a series of errors in the definitions of the LDOs the AXP20x
     regulators, some of which had always been present and some of which
     were introduced in the merge window"

* tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: da9063: Correct module alias prefix to fix module autoloading
  regulator: axp20x: Fix axp22x ldo_io registration error on cold boot
  regulator: axp20x: Fix axp22x ldo_io voltage ranges
  regulator: axp20x: Fix LDO4 linear voltage range
  regulator: s2mps11: Fix invalid selector mask and voltages for buck9
  regulator: gpio: check return value of of_get_named_gpio