linux-stable.git/include/linux, branch v4.5.5

regulator: s2mps11: Fix invalid selector mask and voltages for buck9

2016-05-19T01:35:12+00:00

commit 3b672623079bb3e5685b8549e514f2dfaa564406 upstream.

The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.

The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
	mmc1: card never left busy state
	mmc1: error -110 whilst initialising SD card

During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.

Signed-off-by: Krzysztof Kozlowski 
Reviewed-by: Javier Martinez Canillas 
Tested-by: Javier Martinez Canillas 
Signed-off-by: Mark Brown 
Signed-off-by: Greg Kroah-Hartman

vfs: add vfs_select_inode() helper

2016-05-19T01:35:12+00:00

commit 54d5ca871e72f2bb172ec9323497f01cd5091ec7 upstream.

Signed-off-by: Miklos Szeredi 
Signed-off-by: Greg Kroah-Hartman

mm: thp: calculate the mapcount correctly for THP pages during WP faults

2016-05-19T01:35:09+00:00

commit 6d0a07edd17cfc12fdc1f36de8072fa17cc3666f upstream.

This will provide fully accuracy to the mapcount calculation in the
write protect faults, so page pinning will not get broken by false
positive copy-on-writes.

total_mapcount() isn't the right calculation needed in
reuse_swap_page(), so this introduces a page_trans_huge_mapcount()
that is effectively the full accurate return value for page_mapcount()
if dealing with Transparent Hugepages, however we only use the
page_trans_huge_mapcount() during COW faults where it strictly needed,
due to its higher runtime cost.

This also provide at practical zero cost the total_mapcount
information which is needed to know if we can still relocate the page
anon_vma to the local vma. If page_trans_huge_mapcount() returns 1 we
can reuse the page no matter if it's a pte or a pmd_trans_huge
triggering the fault, but we can only relocate the page anon_vma to
the local vma->anon_vma if we're sure it's only this "vma" mapping the
whole THP physical range.

Kirill A. Shutemov discovered the problem with moving the page
anon_vma to the local vma->anon_vma in a previous version of this
patch and another problem in the way page_move_anon_rmap() was called.

Andrew Morton discovered that CONFIG_SWAP=n wouldn't build in a
previous version, because reuse_swap_page must be a macro to call
page_trans_huge_mapcount from swap.h, so this uses a macro again
instead of an inline function. With this change at least it's a less
dangerous usage than it was before, because "page" is used only once
now, while with the previous code reuse_swap_page(page++) would have
called page_mapcount on page+1 and it would have increased page twice
instead of just once.

Dean Luick noticed an uninitialized variable that could result in a
rmap inefficiency for the non-THP case in a previous version.

Mike Marciniszyn said:

: Our RDMA tests are seeing an issue with memory locking that bisects to
: commit 61f5d698cc97 ("mm: re-enable THP")
:
: The test program registers two rather large MRs (512M) and RDMA
: writes data to a passive peer using the first and RDMA reads it back
: into the second MR and compares that data.  The sizes are chosen randomly
: between 0 and 1024 bytes.
:
: The test will get through a few (<= 4 iterations) and then gets a
: compare error.
:
: Tracing indicates the kernel logical addresses associated with the individual
: pages at registration ARE correct , the data in the "RDMA read response only"
: packets ARE correct.
:
: The "corruption" occurs when the packet crosse two pages that are not physically
: contiguous.   The second page reads back as zero in the program.
:
: It looks like the user VA at the point of the compare error no longer points to
: the same physical address as was registered.
:
: This patch totally resolves the issue!

Link: http://lkml.kernel.org/r/1462547040-1737-2-git-send-email-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli 
Reviewed-by: "Kirill A. Shutemov" 
Reviewed-by: Dean Luick 
Tested-by: Alex Williamson 
Tested-by: Mike Marciniszyn 
Tested-by: Josh Collier 
Cc: Marc Haber 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds 
Signed-off-by: Greg Kroah-Hartman

net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case

2016-05-19T01:35:04+00:00

[ Upstream commit 2c94b53738549d81dc7464a32117d1f5112c64d3 ]

Prior to commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op
when !DEBUG") the implementation of net_dbg_ratelimited() was buggy
for both the DEBUG and CONFIG_DYNAMIC_DEBUG cases.

The bug was that net_ratelimit() was being called and, despite
returning true, nothing was being printed to the console. This
resulted in messages like the following -

"net_ratelimit: %d callbacks suppressed"

with no other output nearby.

After commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when
!DEBUG") the bug is fixed for the DEBUG case. However, there's no
output at all for CONFIG_DYNAMIC_DEBUG case.

This patch restores debug output (if enabled) for the
CONFIG_DYNAMIC_DEBUG case.

Add a definition of net_dbg_ratelimited() for the CONFIG_DYNAMIC_DEBUG
case. The implementation takes care to check that dynamic debugging is
enabled before calling net_ratelimit().

Fixes: d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG")
Signed-off-by: Tim Bingham 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

bpf: fix refcnt overflow

2016-05-19T01:35:04+00:00

[ Upstream commit 92117d8443bc5afacc8d5ba82e541946310f106e ]

On a system with >32Gbyte of phyiscal memory and infinite RLIMIT_MEMLOCK,
the malicious application may overflow 32-bit bpf program refcnt.
It's also possible to overflow map refcnt on 1Tb system.
Impose 32k hard limit which means that the same bpf program or
map cannot be shared by more than 32k processes.

Fixes: 1be7f75d1668 ("bpf: enable non-root eBPF programs")
Reported-by: Jann Horn 
Signed-off-by: Alexei Starovoitov 
Acked-by: Daniel Borkmann 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net/mlx5e: Use vport MTU rather than physical port MTU

2016-05-19T01:35:03+00:00

[ Upstream commit cd255efff9baadd654d6160e52d17ae7c568c9d3 ]

Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.

SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.

Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.

Signed-off-by: Saeed Mahameed 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net/mlx5e: Device's mtu field is u16 and not int

2016-05-19T01:35:02+00:00

[ Upstream commit 046339eaab26804f52f6604877f5674f70815b26 ]

For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.

Signed-off-by: Saeed Mahameed 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

soreuseport: fix ordering for mixed v4/v6 sockets

2016-05-19T01:35:01+00:00

[ Upstream commit d894ba18d4e449b3a7f6eb491f16c9e02933736e ]

With the SO_REUSEPORT socket option, it is possible to create sockets
in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address.
This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on
the AF_INET6 sockets.

Prior to the commits referenced below, an incoming IPv4 packet would
always be routed to a socket of type AF_INET when this mixed-mode was used.
After those changes, the same packet would be routed to the most recently
bound socket (if this happened to be an AF_INET6 socket, it would
have an IPv4 mapped IPv6 address).

The change in behavior occurred because the recent SO_REUSEPORT optimizations
short-circuit the socket scoring logic as soon as they find a match.  They
did not take into account the scoring logic that favors AF_INET sockets
over AF_INET6 sockets in the event of a tie.

To fix this problem, this patch changes the insertion order of AF_INET
and AF_INET6 addresses in the TCP and UDP socket lists when the sockets
have SO_REUSEPORT set.  AF_INET sockets will be inserted at the head of the
list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at
the tail of the list.  This will force AF_INET sockets to always be
considered first.

Fixes: e32ea7e74727 ("soreuseport: fast reuseport UDP socket selection")
Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection")

Reported-by: Maciej Żenczykowski 
Signed-off-by: Craig Gallek 
Signed-off-by: Eric Dumazet 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

mm: memcontrol: let v2 cgroups follow changes in system swappiness

2016-05-11T09:21:31+00:00

commit 4550c4e157ca3da929593bb6c64080a59141af35 upstream.

Cgroup2 currently doesn't have a per-cgroup swappiness setting.  We
might want to add one later - that's a different discussion - but until
we do, the cgroups should always follow the system setting.  Otherwise
it will be unchangeably set to whatever the ancestor inherited from the
system setting at the time of cgroup creation.

Signed-off-by: Johannes Weiner 
Acked-by: Michal Hocko 
Acked-by: Vladimir Davydov 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds 
Signed-off-by: Greg Kroah-Hartman

Minimal fix-up of bad hashing behavior of hash_64()

2016-05-11T09:21:31+00:00

commit 689de1d6ca95b3b5bd8ee446863bf81a4883ea25 upstream.

This is a fairly minimal fixup to the horribly bad behavior of hash_64()
with certain input patterns.

In particular, because the multiplicative value used for the 64-bit hash
was intentionally bit-sparse (so that the multiply could be done with
shifts and adds on architectures without hardware multipliers), some
bits did not get spread out very much.  In particular, certain fairly
common bit ranges in the input (roughly bits 12-20: commonly with the
most information in them when you hash things like byte offsets in files
or memory that have block factors that mean that the low bits are often
zero) would not necessarily show up much in the result.

There's a bigger patch-series brewing to fix up things more completely,
but this is the fairly minimal fix for the 64-bit hashing problem.  It
simply picks a much better constant multiplier, spreading the bits out a
lot better.

NOTE! For 32-bit architectures, the bad old hash_64() remains the same
for now, since 64-bit multiplies are expensive.  The bigger hashing
cleanup will replace the 32-bit case with something better.

The new constants were picked by George Spelvin who wrote that bigger
cleanup series.  I just picked out the constants and part of the comment
from that series.

Cc: George Spelvin 
Cc: Thomas Gleixner 
Signed-off-by: Linus Torvalds 
Signed-off-by: Greg Kroah-Hartman