linux-stable.git/include/linux, branch v3.12.53 Linux kernel stable tree module: remove MODULE_GENERIC_TABLE 2016-01-13T08:14:29+00:00 Rusty Russell rusty@rustcorp.com.au 2014-02-03T00:45:13+00:00 1bf7e534ba65babb46a3d7f3cd9b3bdf41c27a4a commit cff26a51da5d206d3baf871e75778da44710219d upstream. MODULE_DEVICE_TABLE() calles MODULE_GENERIC_TABLE(); make it do the work directly. This also removes a wart introduced in the last patch, where the alias is defined to be an unknown struct type "struct type##__##name##_device_id" instead of "struct type##_device_id" (it's an extern so GCC doesn't care, but it's wrong). The other user of MODULE_GENERIC_TABLE (ISAPNP_CARD_TABLE) is unused, so delete it. Bryan: gcc v3.3.2 cares Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Bryan Kadzban <bryan@kadzban.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit cff26a51da5d206d3baf871e75778da44710219d upstream.

MODULE_DEVICE_TABLE() calles MODULE_GENERIC_TABLE(); make it do the
work directly.  This also removes a wart introduced in the last patch,
where the alias is defined to be an unknown struct type "struct
type##__##name##_device_id" instead of "struct type##_device_id" (it's
an extern so GCC doesn't care, but it's wrong).

The other user of MODULE_GENERIC_TABLE (ISAPNP_CARD_TABLE) is unused,
so delete it.

Bryan: gcc v3.3.2 cares

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Bryan Kadzban <bryan@kadzban.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
block: Always check queue limits for cloned requests 2016-01-11T15:07:39+00:00 Hannes Reinecke hare@suse.de 2015-11-26T07:46:57+00:00 052bd81382379ccaf002ae7a0c3d4ff6f058428b commit bf4e6b4e757488dee1b6a581f49c7ac34cd217f8 upstream. When a cloned request is retried on other queues it always needs to be checked against the queue limits of that queue. Otherwise the calculations for nr_phys_segments might be wrong, leading to a crash in scsi_init_sgtable(). To clarify this the patch renames blk_rq_check_limits() to blk_cloned_rq_check_limits() and removes the symbol export, as the new function should only be used for cloned requests and never exported. Cc: Mike Snitzer <snitzer@redhat.com> Cc: Ewan Milne <emilne@redhat.com> Cc: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Fixes: e2a60da74 ("block: Clean up special command handling logic") Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit bf4e6b4e757488dee1b6a581f49c7ac34cd217f8 upstream.

When a cloned request is retried on other queues it always needs
to be checked against the queue limits of that queue.
Otherwise the calculations for nr_phys_segments might be wrong,
leading to a crash in scsi_init_sgtable().

To clarify this the patch renames blk_rq_check_limits()
to blk_cloned_rq_check_limits() and removes the symbol
export, as the new function should only be used for
cloned requests and never exported.

Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Ewan Milne <emilne@redhat.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Fixes: e2a60da74 ("block: Clean up special command handling logic")
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
USB: add quirk for devices with broken LPM 2016-01-05T16:48:51+00:00 Alan Stern stern@rowland.harvard.edu 2015-12-10T20:27:21+00:00 9963c40635d4407c2f40d946a74bf3a082ed4c87 commit ad87e03213b552a5c33d5e1e7a19a73768397010 upstream. Some USB device / host controller combinations seem to have problems with Link Power Management. For example, Steinar found that his xHCI controller wouldn't handle bandwidth calculations correctly for two video cards simultaneously when LPM was enabled, even though the bus had plenty of bandwidth available. This patch introduces a new quirk flag for devices that should remain disabled for LPM, and creates quirk entries for Steinar's devices. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit ad87e03213b552a5c33d5e1e7a19a73768397010 upstream.

Some USB device / host controller combinations seem to have problems
with Link Power Management.  For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.

This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
ext4, jbd2: ensure entering into panic after recording an error in superblock 2016-01-05T16:48:50+00:00 Daeho Jeong daeho.jeong@samsung.com 2015-10-18T21:02:56+00:00 d8cd31d22be717be1db3bbb21c85acf8c90be2e8 commit 4327ba52afd03fc4b5afa0ee1d774c9c5b0e85c5 upstream. If a EXT4 filesystem utilizes JBD2 journaling and an error occurs, the journaling will be aborted first and the error number will be recorded into JBD2 superblock and, finally, the system will enter into the panic state in "errors=panic" option. But, in the rare case, this sequence is little twisted like the below figure and it will happen that the system enters into panic state, which means the system reset in mobile environment, before completion of recording an error in the journal superblock. In this case, e2fsck cannot recognize that the filesystem failure occurred in the previous run and the corruption wouldn't be fixed. Task A Task B ext4_handle_error() -> jbd2_journal_abort() -> __journal_abort_soft() -> __jbd2_journal_abort_hard() | -> journal->j_flags |= JBD2_ABORT; | | __ext4_abort() | -> jbd2_journal_abort() | | -> __journal_abort_soft() | | -> if (journal->j_flags & JBD2_ABORT) | | return; | -> panic() | -> jbd2_journal_update_sb_errno() Tested-by: Hobin Woo <hobin.woo@samsung.com> Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit 4327ba52afd03fc4b5afa0ee1d774c9c5b0e85c5 upstream.

If a EXT4 filesystem utilizes JBD2 journaling and an error occurs, the
journaling will be aborted first and the error number will be recorded
into JBD2 superblock and, finally, the system will enter into the
panic state in "errors=panic" option.  But, in the rare case, this
sequence is little twisted like the below figure and it will happen
that the system enters into panic state, which means the system reset
in mobile environment, before completion of recording an error in the
journal superblock. In this case, e2fsck cannot recognize that the
filesystem failure occurred in the previous run and the corruption
wouldn't be fixed.

Task A                        Task B
ext4_handle_error()
-> jbd2_journal_abort()
  -> __journal_abort_soft()
    -> __jbd2_journal_abort_hard()
    | -> journal->j_flags |= JBD2_ABORT;
    |
    |                         __ext4_abort()
    |                         -> jbd2_journal_abort()
    |                         | -> __journal_abort_soft()
    |                         |   -> if (journal->j_flags & JBD2_ABORT)
    |                         |           return;
    |                         -> panic()
    |
    -> jbd2_journal_update_sb_errno()

Tested-by: Hobin Woo <hobin.woo@samsung.com>
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
ipv6: add complete rcu protection around np->opt 2016-01-05T15:11:14+00:00 Eric Dumazet edumazet@google.com 2015-11-30T03:37:57+00:00 71781d1f85bc02bcdb29b18e9e76f1d49118ddc8 [ Upstream commit 45f6fad84cc305103b28d73482b344d7f5b76f39 ] This patch addresses multiple problems : UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions while socket is not locked : Other threads can change np->opt concurrently. Dmitry posted a syzkaller (http://github.com/google/syzkaller) program desmonstrating use-after-free. Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock() and dccp_v6_request_recv_sock() also need to use RCU protection to dereference np->opt once (before calling ipv6_dup_options()) This patch adds full RCU protection to np->opt Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
[ Upstream commit 45f6fad84cc305103b28d73482b344d7f5b76f39 ]

This patch addresses multiple problems :

UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.

Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())

This patch adds full RCU protection to np->opt

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Revert "USB: Add device quirk for ASUS T100 Base Station keyboard" 2015-10-28T15:38:37+00:00 Jiri Slaby jslaby@suse.cz 2015-10-27T12:06:27+00:00 ce0c9313b7dd8b929c0c778f591a21dcf699a20b This reverts commit e25ecd21ffdbf1f8287103ccf97205fc30088344 in 3.12, upstream commit ddbe1fca0bcb87ca8c199ea873a456ca8a948567 (USB: Add device quirk for ASUS T100 Base Station keyboard). It was applied twice to 3.12 and one backport is bogus. Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
This reverts commit e25ecd21ffdbf1f8287103ccf97205fc30088344 in 3.12,
upstream commit ddbe1fca0bcb87ca8c199ea873a456ca8a948567 (USB: Add
device quirk for ASUS T100 Base Station keyboard).

It was applied twice to 3.12 and one backport is bogus.

Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
usb: core: implement AMD remote wakeup quirk 2015-10-28T15:38:35+00:00 Huang Rui ray.huang@amd.com 2013-09-16T15:47:28+00:00 81e3e4d245028c5467019b2417bb79c8d292289d commit 7868943db1668fba898cf71bed1506c19d6958aa upstream. The following patch is required to resolve remote wake issues with certain devices. Issue description: If the remote wake is issued from the device in a specific timing condition while the system is entering sleep state then it may cause system to auto wake on subsequent sleep cycle. Root cause: Host controller rebroadcasts the Resume signal > 100 µseconds after receiving the original resume event from the device. For proper function, some devices may require the rebroadcast of resume event within the USB spec of 100µS. Workaroud: 1. Filter the AMD platforms with Yangtze chipset, then judge of all the usb devices are mouse or not. And get out the port id which attached a mouse with Pixart controller. 2. Then reset the port which attached issue device during system resume from S3. [Q] Why the special devices are only mice? Would high speed devices such as 3G modem or USB Bluetooth adapter trigger this issue? - Current this sensitivity is only confined to devices that use Pixart controllers. This controller is designed for use with LS mouse devices only. We have not observed any other devices failing. There may be a small risk for other devices also but this patch (reset device in resume phase) will cover the cases if required. [Q] Shouldn’t the resume signal be sent within 100 us for every device? - The Host controller may not send the resume signal within 100us, this our host controller specification change. This is why we require the patch to prevent side effects on certain known devices. [Q] Why would clicking mouse INTENSELY to wake the system up trigger this issue? - This behavior is specific to the devices that use Pixart controller. It is timing dependent on when the resume event is triggered during the sleep state. [Q] Is it a host controller issue or mouse? - It is the host controller behavior during resume that triggers the device incorrect behavior on the next resume. This patch sets USB_QUIRK_RESET_RESUME flag for these Pixart-based mice when they attached to platforms with AMD Yangtze chipset. Signed-off-by: Huang Rui <ray.huang@amd.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit 7868943db1668fba898cf71bed1506c19d6958aa upstream.

The following patch is required to resolve remote wake issues with
certain devices.

Issue description:
If the remote wake is issued from the device in a specific timing
condition while the system is entering sleep state then it may cause
system to auto wake on subsequent sleep cycle.

Root cause:
Host controller rebroadcasts the Resume signal > 100 µseconds after
receiving the original resume event from the device. For proper
function, some devices may require the rebroadcast of resume event
within the USB spec of 100µS.

Workaroud:
1. Filter the AMD platforms with Yangtze chipset, then judge of all the usb
devices are mouse or not. And get out the port id which attached a mouse
with Pixart controller.
2. Then reset the port which attached issue device during system resume
from S3.

[Q] Why the special devices are only mice? Would high speed devices
such as 3G modem or USB Bluetooth adapter trigger this issue?
- Current this sensitivity is only confined to devices that use Pixart
  controllers. This controller is designed for use with LS mouse
devices only. We have not observed any other devices failing. There
may be a small risk for other devices also but this patch (reset
device in resume phase) will cover the cases if required.

[Q] Shouldn’t the resume signal be sent within 100 us for every
device?
- The Host controller may not send the resume signal within 100us,
  this our host controller specification change. This is why we
require the patch to prevent side effects on certain known devices.

[Q] Why would clicking mouse INTENSELY to wake the system up trigger
this issue?
- This behavior is specific to the devices that use Pixart controller.
  It is timing dependent on when the resume event is triggered during
the sleep state.

[Q] Is it a host controller issue or mouse?
- It is the host controller behavior during resume that triggers the
  device incorrect behavior on the next resume.

This patch sets USB_QUIRK_RESET_RESUME flag for these Pixart-based mice
when they attached to platforms with AMD Yangtze chipset.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
skbuff: Fix skb checksum partial check. 2015-10-28T15:38:14+00:00 Pravin B Shelar pshelar@nicira.com 2015-09-29T00:24:25+00:00 21b3d84559613290efd304ef929a0fb8fcf58950 [ Upstream commit 31b33dfb0a144469dd805514c9e63f4993729a48 ] Earlier patch 6ae459bda tried to detect void ckecksum partial skb by comparing pull length to checksum offset. But it does not work for all cases since checksum-offset depends on updates to skb->data. Following patch fixes it by validating checksum start offset after skb-data pointer is updated. Negative value of checksum offset start means there is no need to checksum. Fixes: 6ae459bda ("skbuff: Fix skb checksum flag on skb pull") Reported-by: Andrew Vagin <avagin@odin.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
[ Upstream commit 31b33dfb0a144469dd805514c9e63f4993729a48 ]

Earlier patch 6ae459bda tried to detect void ckecksum partial
skb by comparing pull length to checksum offset. But it does
not work for all cases since checksum-offset depends on
updates to skb->data.

Following patch fixes it by validating checksum start offset
after skb-data pointer is updated. Negative value of checksum
offset start means there is no need to checksum.

Fixes: 6ae459bda ("skbuff: Fix skb checksum flag on skb pull")
Reported-by: Andrew Vagin <avagin@odin.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
skbuff: Fix skb checksum flag on skb pull 2015-10-28T15:38:13+00:00 Pravin B Shelar pshelar@nicira.com 2015-09-22T19:57:53+00:00 eef6d4fd7ebd613a77480c4d265572bc63ec17fe [ Upstream commit 6ae459bdaaeebc632b16e54dcbabb490c6931d61 ] VXLAN device can receive skb with checksum partial. But the checksum offset could be in outer header which is pulled on receive. This results in negative checksum offset for the skb. Such skb can cause the assert failure in skb_checksum_help(). Following patch fixes the bug by setting checksum-none while pulling outer header. Following is the kernel panic msg from old kernel hitting the bug. ------------[ cut here ]------------ kernel BUG at net/core/dev.c:1906! RIP: 0010:[<ffffffff81518034>] skb_checksum_help+0x144/0x150 Call Trace: <IRQ> [<ffffffffa0164c28>] queue_userspace_packet+0x408/0x470 [openvswitch] [<ffffffffa016614d>] ovs_dp_upcall+0x5d/0x60 [openvswitch] [<ffffffffa0166236>] ovs_dp_process_packet_with_key+0xe6/0x100 [openvswitch] [<ffffffffa016629b>] ovs_dp_process_received_packet+0x4b/0x80 [openvswitch] [<ffffffffa016c51a>] ovs_vport_receive+0x2a/0x30 [openvswitch] [<ffffffffa0171383>] vxlan_rcv+0x53/0x60 [openvswitch] [<ffffffffa01734cb>] vxlan_udp_encap_recv+0x8b/0xf0 [openvswitch] [<ffffffff8157addc>] udp_queue_rcv_skb+0x2dc/0x3b0 [<ffffffff8157b56f>] __udp4_lib_rcv+0x1cf/0x6c0 [<ffffffff8157ba7a>] udp_rcv+0x1a/0x20 [<ffffffff8154fdbd>] ip_local_deliver_finish+0xdd/0x280 [<ffffffff81550128>] ip_local_deliver+0x88/0x90 [<ffffffff8154fa7d>] ip_rcv_finish+0x10d/0x370 [<ffffffff81550365>] ip_rcv+0x235/0x300 [<ffffffff8151ba1d>] __netif_receive_skb+0x55d/0x620 [<ffffffff8151c360>] netif_receive_skb+0x80/0x90 [<ffffffff81459935>] virtnet_poll+0x555/0x6f0 [<ffffffff8151cd04>] net_rx_action+0x134/0x290 [<ffffffff810683d8>] __do_softirq+0xa8/0x210 [<ffffffff8162fe6c>] call_softirq+0x1c/0x30 [<ffffffff810161a5>] do_softirq+0x65/0xa0 [<ffffffff810687be>] irq_exit+0x8e/0xb0 [<ffffffff81630733>] do_IRQ+0x63/0xe0 [<ffffffff81625f2e>] common_interrupt+0x6e/0x6e Reported-by: Anupam Chanda <achanda@vmware.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
[ Upstream commit 6ae459bdaaeebc632b16e54dcbabb490c6931d61 ]

VXLAN device can receive skb with checksum partial. But the checksum
offset could be in outer header which is pulled on receive. This results
in negative checksum offset for the skb. Such skb can cause the assert
failure in skb_checksum_help(). Following patch fixes the bug by setting
checksum-none while pulling outer header.

Following is the kernel panic msg from old kernel hitting the bug.

------------[ cut here ]------------
kernel BUG at net/core/dev.c:1906!
RIP: 0010:[<ffffffff81518034>] skb_checksum_help+0x144/0x150
Call Trace:
<IRQ>
[<ffffffffa0164c28>] queue_userspace_packet+0x408/0x470 [openvswitch]
[<ffffffffa016614d>] ovs_dp_upcall+0x5d/0x60 [openvswitch]
[<ffffffffa0166236>] ovs_dp_process_packet_with_key+0xe6/0x100 [openvswitch]
[<ffffffffa016629b>] ovs_dp_process_received_packet+0x4b/0x80 [openvswitch]
[<ffffffffa016c51a>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa0171383>] vxlan_rcv+0x53/0x60 [openvswitch]
[<ffffffffa01734cb>] vxlan_udp_encap_recv+0x8b/0xf0 [openvswitch]
[<ffffffff8157addc>] udp_queue_rcv_skb+0x2dc/0x3b0
[<ffffffff8157b56f>] __udp4_lib_rcv+0x1cf/0x6c0
[<ffffffff8157ba7a>] udp_rcv+0x1a/0x20
[<ffffffff8154fdbd>] ip_local_deliver_finish+0xdd/0x280
[<ffffffff81550128>] ip_local_deliver+0x88/0x90
[<ffffffff8154fa7d>] ip_rcv_finish+0x10d/0x370
[<ffffffff81550365>] ip_rcv+0x235/0x300
[<ffffffff8151ba1d>] __netif_receive_skb+0x55d/0x620
[<ffffffff8151c360>] netif_receive_skb+0x80/0x90
[<ffffffff81459935>] virtnet_poll+0x555/0x6f0
[<ffffffff8151cd04>] net_rx_action+0x134/0x290
[<ffffffff810683d8>] __do_softirq+0xa8/0x210
[<ffffffff8162fe6c>] call_softirq+0x1c/0x30
[<ffffffff810161a5>] do_softirq+0x65/0xa0
[<ffffffff810687be>] irq_exit+0x8e/0xb0
[<ffffffff81630733>] do_IRQ+0x63/0xe0
[<ffffffff81625f2e>] common_interrupt+0x6e/0x6e

Reported-by: Anupam Chanda <achanda@vmware.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
security: fix typo in security_task_prctl 2015-10-28T15:38:02+00:00 Jann Horn jann@thejh.net 2015-09-18T21:41:23+00:00 cfc6ca1adb7698e6030f8710579f71f618371182 commit b7f76ea2ef6739ee484a165ffbac98deb855d3d3 upstream. Signed-off-by: Jann Horn <jann@thejh.net> Reviewed-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit b7f76ea2ef6739ee484a165ffbac98deb855d3d3 upstream.

Signed-off-by: Jann Horn <jann@thejh.net>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>