linux-stable.git/include/linux/usb/hcd.h, branch v3.4.112

USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)

2015-06-19T03:40:13+00:00

commit 074f9dd55f9cab1b82690ed7e44bcf38b9616ce0 upstream.

Currently the USB stack assumes that all host controller drivers are
capable of receiving wakeup requests from downstream devices.
However, this isn't true for the isp1760-hcd driver, which means that
it isn't safe to do a runtime suspend of any device attached to a
root-hub port if the device requires wakeup.

This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure
and sets the flag in isp1760-hcd.  The core is modified to prevent a
direct child of the root hub from being put into runtime suspend with
wakeup enabled if the flag is set.

Signed-off-by: Alan Stern 
Tested-by: Nicolas Pitre 
Signed-off-by: Greg Kroah-Hartman 
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li

usb: core: buffer: smallest buffer should start at ARCH_DMA_MINALIGN

2015-06-19T03:40:11+00:00

commit 5efd2ea8c9f4f12916ffc8ba636792ce052f6911 upstream.

the following error pops up during "testusb -a -t 10"
| musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128,	f134e000/be842000 (bad dma)
hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of
size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in
hcd_buffer_alloc() returning memory which is 32 bytes aligned and it
might by identified by buffer_offset() as another buffer. This means the
buffer which is on a 32 byte boundary will not get freed, instead it
tries to free another buffer with the error message.

This patch fixes the issue by creating the smallest DMA buffer with the
size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is
smaller). This might be 32, 64 or even 128 bytes. The next three pools
will have the size 128, 512 and 2048.
In case the smallest pool is 128 bytes then we have only three pools
instead of four (and zero the first entry in the array).
The last pool size is always 2048 bytes which is the assumed PAGE_SIZE /
2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where
we would end up with 8KiB buffer in case we have 16KiB pages.
Instead I think it makes sense to have a common size(s) and extend them
if there is need to.
There is a BUILD_BUG_ON() now in case someone has a minalign of more than
128 bytes.

Signed-off-by: Sebastian Andrzej Siewior 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Zefan Li

USB: fix build error when CONFIG_PM_SLEEP isn't enabled

2014-04-14T13:44:27+00:00

commit 9d8924297cd9c256c23c02abae40202563452453 upstream.

This patch fixes a build error that occurs when CONFIG_PM is enabled
and CONFIG_PM_SLEEP isn't:

>> drivers/usb/host/ohci-pci.c:294:10: error: 'usb_hcd_pci_pm_ops' undeclared here (not in a function)
      .pm = &usb_hcd_pci_pm_ops

Since the usb_hcd_pci_pm_ops structure is defined and used when
CONFIG_PM is enabled, its declaration should not be protected by
CONFIG_PM_SLEEP.

Signed-off-by: Alan Stern 
Reported-by: kbuild test robot 
Signed-off-by: Ben Hutchings 
Cc: Yang Yingliang 
Signed-off-by: Greg Kroah-Hartman

USB: add NO_D3_DURING_SLEEP flag and revert 151b61284776be2

2012-06-22T18:37:13+00:00

commit c2fb8a3fa25513de8fedb38509b1f15a5bbee47b upstream.

This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

A similar patch has already been applied as commit
151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during
suspend on ASUS computers).  The patch supersedes that one and reverts
it.  There are two differences:

	The old patch added the flag at the USB level; this patch
	adds it at the PCI level.

	The old patch applied to all chipsets with the same vendor,
	subsystem vendor, and product IDs; this patch makes an
	exception for a known-good system (based on DMI information).

Signed-off-by: Alan Stern 
Tested-by: Dâniel Fraga 
Tested-by: Andrey Rahmatullin 
Tested-by: Steven Rostedt 
Reviewed-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: fix crash during suspend on ASUS computers

2012-04-24T20:55:43+00:00

This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

This fixes Bugzilla #42728.

Signed-off-by: Alan Stern 
Tested-by: Steven Rostedt 
Tested-by: Andrey Rahmatullin 
Tested-by: Oleksij Rempel (fishor) 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: core: hcd: make hcd->irq unsigned

2012-03-01T17:31:22+00:00

There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.

Tested-by: Kuninori Morimoto 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

USB/xHCI: Support device-initiated USB 3.0 resume.

2012-02-14T20:12:26+00:00

USB 3.0 hubs don't have a port suspend change bit (that bit is now
reserved).  Instead, when a host-initiated resume finishes, the hub sets
the port link state change bit.

When a USB 3.0 device initiates remote wakeup, the parent hubs with
their upstream links in U3 will pass the LFPS up the chain.  The first
hub that has an upstream link in U0 (which may be the roothub) will
reflect that LFPS back down the path to the device.

However, the parent hubs in the resumed path will not set their link
state change bit.  Instead, the device that initiated the resume has to
send an asynchronous "Function Wake" Device Notification up to the host
controller.  Therefore, we need a way to notify the USB core of a device
resume without going through the normal hub URB completion method.

First, make the xHCI roothub act like an external USB 3.0 hub and not
pass up the port link state change bit when a device-initiated resume
finishes.  Introduce a new xHCI bit field, port_remote_wakeup, so that
we can tell the difference between a port coming out of the U3Exit state
(host-initiated resume) and the RExit state (ending state of
device-initiated resume).

Since the USB core can't tell whether a port on a hub has resumed by
looking at the Hub Status buffer, we need to introduce a bitfield,
wakeup_bits, that indicates which ports have resumed.  When the xHCI
driver notices a port finishing a device-initiated resume, we call into
a new USB core function, usb_wakeup_notification(), that will set
the right bit in wakeup_bits, and kick khubd for that hub.

We also call usb_wakeup_notification() when the Function Wake Device
Notification is received by the xHCI driver.  This covers the case where
the link between the roothub and the first-tier hub is in U0, and the
hub reflects the resume signaling back to the device without giving any
indication it has done so until the device sends the Function Wake
notification.

Change the code in khubd that handles the remote wakeup to look at the
state the USB core thinks the device is in, and handle the remote wakeup
if the port's wakeup bit is set.

This patch only takes care of the case where the device is attached
directly to the roothub, or the USB 3.0 hub that is attached to the root
hub is the device sending the Function Wake Device Notification (e.g.
because a new USB device was attached).  The other cases will be covered
in a second patch.

Signed-off-by: Sarah Sharp

USB: Remove the SAW_IRQ hcd flag

2011-11-15T00:46:06+00:00

The HCD_FLAG_SAW_IRQ flag was introduced in order to catch IRQ routing
errors: If an URB was unlinked and the host controller hadn't gotten
any IRQs, it seemed likely that the IRQs were directed to the wrong
vector.

This warning hasn't come up in many years, as far as I know; interrupt
routing now seems to be well under control.  Therefore there's no
reason to keep the flag around any more.  This patch (as1495) finally
removes it.

Signed-off-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: fix ehci alignment error

2011-10-10T23:43:53+00:00

The Kirkwood gave an unaligned memory access error on
line 742 of drivers/usb/host/echi-hcd.c:
"ehci->last_periodic_enable = ktime_get_real();"

Signed-off-by: Harro Haan 
Cc: stable 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

xHCI: set USB2 hardware LPM

2011-09-26T22:51:10+00:00

If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.

If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.

Signed-off-by: Andiry Xu 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman