[ Upstream commit 54aa39a513dbf2164ca462a19f04519b2407a224 ]

Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.

Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.

Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 47f753c1108e287edb3e27fad8a7511a9d55578e upstream.

Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation
of Split Header (SPH) feature is not supported for Ipv4 fragmented packet.
This SPH limitation will cause ping failure when the packets size exceed
the MTU size. For example, the issue happens once the basic ping packet
size is larger than the configured MTU size and the data is lost inside
the fragmented packet, replaced by zeros/corrupted values, and leads to
ping fail.

So, disable the Split Header for Intel platforms.

v2: Add fixes tag in commit message.

Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b2aae654a4794ef898ad33a179f341eb610f6b85 ]

Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

The current IP register MAC_HW_Feature1[ADDR64] only defines
32/40/64 bit width, but some SOCs support others like i.MX8MP
support 34 bits but it maps to 40 bits width in MAC_HW_Feature1[ADDR64].
So overwrite dma_cap.addr64 according to HW real design.

Fixes: 94abdad6974a ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding reference clock (1us tic) for all LPI timer on Intel platforms.
The reference clock is derived from ptp clk. This also enables all LPI
counter.

Signed-off-by: Rusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.

When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
  will pass up all rx packets that failed address filtering (similar to
  promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
  filters and get routed to selected VFFQ Rx queue.

Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to enable Intel SERDES power up/down sequence. The SERDES
converts 8/10 bits data to SGMII signal. Below is an example of
HW configuration for SGMII mode. The SERDES is located in the PHY IF
in the diagram below.

<-----------------GBE Controller---------->|<--External PHY chip-->
+----------+         +----+            +---+           +----------+
|   EQoS   | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
|   MAC    |         |xPCS|            |IF |           | PHY      |
+----------+         +----+            +---+           +----------+
       ^               ^                 ^                ^
       |               |                 |                |
       +---------------------MDIO-------------------------+

PHY IF configuration and status registers are accessible through
mdio address 0x15 which is defined as mdio_adhoc_addr. During D0,
The driver will need to power up PHY IF by changing the power state
to P0. Likewise, for D3, the driver sets PHY IF power state to P3.

Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds the initial hooks for TBS support. This needs a 32 byte descriptor
in order for it to work with current HW. Adds all the logic for Enhanced
Descriptors in main core but no HW related logic for now.

Changes from v2:
- Use bitfield for TBS status / support (Jakub)
- Remove unneeded cache alignment (Jakub)
- Fix checkpatch issues

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Adds the support for EST in GMAC5+ cores. This feature allows to offload
scheduling of queues opening time to the IP.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>