If a raid1 has only one working drive and it has a sector which
gives an error on read, then an attempt to recover onto a spare will
fail, but as the single remaining drive is not removed from the
array, the recovery will be immediately re-attempted, resulting
in an infinite recovery loop.

So detect this situation and don't retry recovery once an error
on the lone remaining drive is detected.

Allow recovery to be retried once every time a spare is added
in case the problem wasn't actually a media error.

Signed-off-by: NeilBrown <neilb@suse.de>

Using sequential numbers to identify md devices is somewhat artificial.
Using names can be a lot more user-friendly.

Also, creating md devices by opening the device special file is a bit
awkward.

So this patch provides a new option for creating and naming devices.

Writing a name such as "md_home" to
    /sys/modules/md_mod/parameters/new_array
will cause an array with that name to be created.  It will appear in
/sys/block/ /proc/partitions and /proc/mdstat as 'md_home'.
It will have an arbitrary minor number allocated.

md devices that a created by an open are destroyed on the last
close when the device is inactive.
For named md devices, they will not be destroyed until the array
is explicitly stopped, either with the STOP_ARRAY ioctl or by
writing 'clear' to /sys/block/md_XXXX/md/array_state.

The name of the array must start 'md_' to avoid conflict with
other devices.

Signed-off-by: NeilBrown <neilb@suse.de>

Currently md devices, once created, never disappear until the module
is unloaded.  This is essentially because the gendisk holds a
reference to the mddev, and the mddev holds a reference to the
gendisk, this a circular reference.

If we drop the reference from mddev to gendisk, then we need to ensure
that the mddev is destroyed when the gendisk is destroyed.  However it
is not possible to hook into the gendisk destruction process to enable
this.

So we drop the reference from the gendisk to the mddev and destroy the
gendisk when the mddev gets destroyed.  However this has a
complication.
Between the call
   __blkdev_get->get_gendisk->kobj_lookup->md_probe
and the call
   __blkdev_get->md_open

there is no obvious way to hold a reference on the mddev any more, so
unless something is done, it will disappear and gendisk will be
destroyed prematurely.

Also, once we decide to destroy the mddev, there will be an unlockable
moment before the gendisk is unlinked (blk_unregister_region) during
which a new reference to the gendisk can be created.  We need to
ensure that this reference can not be used.  i.e. the ->open must
fail.

So:
 1/  in md_probe we set a flag in the mddev (hold_active) which
     indicates that the array should be treated as active, even
     though there are no references, and no appearance of activity.
     This is cleared by md_release when the device is closed if it
     is no longer needed.
     This ensures that the gendisk will survive between md_probe and
     md_open.

 2/  In md_open we check if the mddev we expect to open matches
     the gendisk that we did open.
     If there is a mismatch we return -ERESTARTSYS and modify
     __blkdev_get to retry from the top in that case.
     In the -ERESTARTSYS sys case we make sure to wait until
     the old gendisk (that we succeeded in opening) is really gone so
     we loop at most once.

Some udev configurations will always open an md device when it first
appears.   If we allow an md device that was just created by an open
to disappear on an immediate close, then this can race with such udev
configurations and result in an infinite loop the device being opened
and closed, then re-open due to the 'ADD' even from the first open,
and then close and so on.
So we make sure an md device, once created by an open, remains active
at least until some md 'ioctl' has been made on it.  This means that
all normal usage of md devices will allow them to disappear promptly
when not needed, but the worst that an incorrect usage will do it
cause an inactive md device to be left in existence (it can easily be
removed).

As an array can be stopped by writing to a sysfs attribute
  echo clear > /sys/block/mdXXX/md/array_state
we need to use scheduled work for deleting the gendisk and other
kobjects.  This allows us to wait for any pending gendisk deletion to
complete by simply calling flush_scheduled_work().



Signed-off-by: NeilBrown <neilb@suse.de>

The rdev_for_each macro defined in <linux/raid/md_k.h> is identical to
list_for_each_entry_safe, from <linux/list.h>, it should be defined to
use list_for_each_entry_safe, instead of reinventing the wheel.

But some calls to each_entry_safe don't really need a safe version,
just a direct list_for_each_entry is enough, this could save a temp
variable (tmp) in every function that used rdev_for_each.

In this patch, most rdev_for_each loops are replaced by list_for_each_entry,
totally save many tmp vars; and only in the other situations that will call
list_del to delete an entry, the safe version is used.

Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

There is no compelling need for this, but sysfs_notify_dirent is a
nicer interface and the change is good for consistency.

Signed-off-by: NeilBrown <neilb@suse.de>

The 'state' file for a device reports, for example, when the device
has failed.  Changes should be reported to userspace ASAP without
the possibility of blocking on low-memory.  sysfs_notify does
have that possibility (as it takes a mutex which can be held
across a kmalloc) so use sysfs_notify_dirent instead.

Signed-off-by: NeilBrown <neilb@suse.de>

Now that we have sysfs_notify_dirent, use it to notify changes
to md/array_state.
As sysfs_notify_dirent can be called in atomic context, we can
remove the delayed notify and the MD_NOTIFY_ARRAY_STATE flag.

Signed-off-by: NeilBrown <neilb@suse.de>

sysfs_notify might sleep, so do not call it from md_safemode_timeout.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>

All modifications and most access to the mddev->disks list are made
under the reconfig_mutex lock.  However there are three places where
the list is walked without any locking.  If a reconfig happens at this
time, havoc (and oops) can ensue.

So use RCU to protect these accesses:
  - wrap them in rcu_read_{,un}lock()
  - use list_for_each_entry_rcu
  - add to the list with list_add_rcu
  - delete from the list with list_del_rcu
  - delay the 'free' with call_rcu rather than schedule_work

Note that export_rdev did a list_del_init on this list.  In almost all
cases the entry was not in the list anymore so it was a no-op and so
safe.  It is no longer safe as after list_del_rcu we may not touch
the list_head.
An audit shows that export_rdev is called:
  - after unbind_rdev_from_array, in which case the delete has
     already been done,
  - after bind_rdev_to_array fails, in which case the delete isn't needed.
  - before the device has been put on a list at all (e.g. in
      add_new_disk where reading the superblock fails).
  - and in autorun devices after a failure when the device is on a
      different list.

So remove the list_del_init call from export_rdev, and add it back
immediately before the called to export_rdev for that last case.

Note also that ->same_set is sometimes used for lists other than
mddev->list (e.g. candidates).  In these cases rcu is not needed.

Signed-off-by: NeilBrown <neilb@suse.de>

Open isn't the only thing that increments ->active.  e.g. reading
/proc/mdstat will increment it briefly.  So to avoid false positives
in testing for concurrent access, introduce a new counter that counts
just the number of times the md device it open.

Signed-off-by: NeilBrown <neilb@suse.de>