Add a mechanism for counting references to the
struct generic_pm_domain_data object pointed to by
dev->power.subsys_data->domain_data if the device in question
belongs to a generic PM domain.

This change is necessary for a subsequent patch making it possible to
allocate that object from within pm_genpd_add_callbacks(), so that
drivers can attach their PM domain device callbacks to devices before
those devices are added to PM domains.

This patch has been tested on the SH7372 Mackerel board.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

On some systems there are CPU cores located in the same power
domains as I/O devices.  Then, power can only be removed from the
domain if all I/O devices in it are not in use and the CPU core
is idle.  Add preliminary support for that to the generic PM domains
framework.

First, the platform is expected to provide a cpuidle driver with one
extra state designated for use with the generic PM domains code.
This state should be initially disabled and its exit_latency value
should be set to whatever time is needed to bring up the CPU core
itself after restoring power to it, not including the domain's
power on latency.  Its .enter() callback should point to a procedure
that will remove power from the domain containing the CPU core at
the end of the CPU power transition.

The remaining characteristics of the extra cpuidle state, referred to
as the "domain" cpuidle state below, (e.g. power usage, target
residency) should be populated in accordance with the properties of
the hardware.

Next, the platform should execute genpd_attach_cpuidle() on the PM
domain containing the CPU core.  That will cause the generic PM
domains framework to treat that domain in a special way such that:

 * When all devices in the domain have been suspended and it is about
   to be turned off, the states of the devices will be saved, but
   power will not be removed from the domain.  Instead, the "domain"
   cpuidle state will be enabled so that power can be removed from
   the domain when the CPU core is idle and the state has been chosen
   as the target by the cpuidle governor.

 * When the first I/O device in the domain is resumed and
   __pm_genpd_poweron(() is called for the first time after
   power has been removed from the domain, the "domain" cpuidle
   state will be disabled to avoid subsequent surprise power removals
   via cpuidle.

The effective exit_latency value of the "domain" cpuidle state
depends on the time needed to bring up the CPU core itself after
restoring power to it as well as on the power on latency of the
domain containing the CPU core.  Thus the "domain" cpuidle state's
exit_latency has to be recomputed every time the domain's power on
latency is updated, which may happen every time power is restored
to the domain, if the measured power on latency is greater than
the latency stored in the corresponding generic_pm_domain structure.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>

The generic PM domains core code currently requires domains to be in
the "power on" state for adding devices to them, but this limitation
turns out to be inconvenient in some situations, so remove it.

For this purpose, make __pm_genpd_add_device() set the device's
need_restore flag if the domain is in the "power off" state, so that
the device's "restore state" (usually .runtime_resume()) callback
is executed when it is resumed after the domain has been turned on.
If the domain is in the "power on" state, the device's need_restore
flag will be cleared by __pm_genpd_add_device(), so that its "save
state" (usually .runtime_suspend()) callback is executed when the
domain is about to be turned off.  However, since that default
behavior need not be always desirable, add a helper function
pm_genpd_dev_need_restore() allowing a device's need_restore flag
to be set/unset at any time.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

The results of the default device stop and domain power off governor
functions for generic PM domains, default_stop_ok() and
default_power_down_ok(), depend only on the timing data of devices,
which are static, and on their PM QoS constraints.  Thus, in theory,
these functions only need to carry out their computations, which may
be time consuming in general, when it is known that the PM QoS
constraint of at least one of the devices in question has changed.

Use the PM QoS notifiers of devices to implement that.  First,
introduce new fields, constraint_changed and max_off_time_changed,
into struct gpd_timing_data and struct generic_pm_domain,
respectively, and register a PM QoS notifier function when adding
a device into a domain that will set those fields to 'true' whenever
the device's PM QoS constraint is modified.  Second, make
default_stop_ok() and default_power_down_ok() use those fields to
decide whether or not to carry out their computations from scratch.

The device and PM domain hierarchies are taken into account in that
and the expense is that the changes of PM QoS constraints of
suspended devices will not be taken into account immediately, which
isn't guaranteed anyway in general.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

The existing default domain power down governor function for PM
domains, default_power_down_ok(), is supposed to check whether or not
the PM QoS latency constraints of the devices in the domain will be
violated if the domain is turned off by pm_genpd_poweroff().
However, the computations carried out by it don't reflect the
definition of the PM QoS latency constrait in
Documentation/ABI/testing/sysfs-devices-power.

Make default_power_down_ok() follow the definition of the PM QoS
latency constrait.  In particular, make it only take latencies into
account, because it doesn't matter how much time has elapsed since
the domain's devices were suspended for the computation.

Remove the break_even_ns and power_off_time fields from
struct generic_pm_domain, because they are not necessary any more.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

The existing default device stop governor function for PM domains,
default_stop_ok(), is supposed to check whether or not the device's
PM QoS latency constraint will be violated if the device is stopped
by pm_genpd_runtime_suspend().  However, the computations carried out
by it don't reflect the definition of the PM QoS latency constrait in
Documentation/ABI/testing/sysfs-devices-power.

Make default_stop_ok() follow the definition of the PM QoS latency
constrait.  In particular, make it take the device's start and stop
latencies correctly.

Add a new field, effective_constraint_ns, to struct gpd_timing_data
and use it to store the difference between the device's PM QoS
constraint and its resume latency for use by the device's parent
(the effective_constraint_ns values for the children are used for
computing the parent's one along with its PM QoS constraint).

Remove the break_even_ns field from struct gpd_timing_data, because
it's not used any more.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Pull <linux/device.h> avoidance patches from Paul Gortmaker:
 "Nearly every subsystem has some kind of header with a proto like:

	void foo(struct device *dev);

  and yet there is no reason for most of these guys to care about the
  sub fields within the device struct.  This allows us to significantly
  reduce the scope of headers including headers.  For this instance, a
  reduction of about 40% is achieved by replacing the include with the
  simple fact that the device is some kind of a struct.

  Unlike the much larger module.h cleanup, this one is simply two
  commits.  One to fix the implicit <linux/device.h> users, and then one
  to delete the device.h includes from the linux/include/ dir wherever
  possible."

* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  device.h: audit and cleanup users in main include dir
  device.h: cleanup users outside of linux/include (C files)

The TMU device on the Mackerel board belongs to the A4R power domain
and loses power when the domain is turned off.  Unfortunately, the
TMU driver is not prepared to cope with such situations and crashes
the system when that happens.  To work around this problem introduce
a new helper function, pm_genpd_dev_always_on(), allowing a device
driver to mark its device as "always on" in case it belongs to a PM
domain, which will make the generic PM domains core code avoid
powering off the domain containing the device, both at run time and
during system suspend.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: stable@vger.kernel.org

The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.

Clean up the users as follows:

1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.

2) For headers not really using anything from device.h, simply
delete the include altogether.

3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h

4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).

Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.

Total removals from #1 and #2: 51.  Total additions coming
from #3: 9.  Total other implicit dependencies from #4: 7.

As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Fix pm_genpd_init() arguments and make sure dev_gpd_data() and
simple_qos_governor exist regardless of CONFIG_PM_GENERIC_DOMAINS
setting.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>