* pci/bjorn-p2p-bridge-windows:
  sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
  PCI: support sizing P2P bridge I/O windows with 1K granularity
  PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
  PCI: allow P2P bridge windows starting at PCI bus address zero

Conflicts:
	drivers/pci/probe.c
	include/linux/pci.h

9d265124d051 and 15a260d53f7c added quirks for P2P bridges that support
I/O windows that start/end at 1K boundaries, not just the 4K boundaries
defined by the PCI spec.  For details, see the IOBL_ADR register and the
EN1K bit in the CNF register in the Intel 82870P2 (P64H2).

These quirks complicate the code that reads P2P bridge windows
(pci_read_bridge_io() and pci_cfg_fake_ranges()) because the bridge
I/O resource is updated in the HEADER quirk, in pci_read_bridge_io(),
in pci_setup_bridge(), and again in the FINAL quirk.  This is confusing
and makes it impossible to reassign the bridge windows after FINAL
quirks are run.

This patch adds support for 1K windows in the generic paths, so the
HEADER quirk only has to enable this support.  The FINAL quirk, which
used to undo damage done by pci_setup_bridge(), is no longer needed.

This removes "if (!res->start) res->start = ..." from pci_read_bridge_io();
that was part of 9d265124d051 to avoid overwriting the resource filled in
by the quirk.  Since pci_read_bridge_io() itself now knows about
granularity, the quirk no longer updates the resource and this test is no
longer needed.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* pci/myron-pcibios_setup:
  xtensa/PCI: factor out pcibios_setup()
  x86/PCI: adjust section annotations for pcibios_setup()
  unicore32/PCI: adjust section annotations for pcibios_setup()
  tile/PCI: factor out pcibios_setup()
  sparc/PCI: factor out pcibios_setup()
  sh/PCI: adjust section annotations for pcibios_setup()
  sh/PCI: factor out pcibios_setup()
  powerpc/PCI: factor out pcibios_setup()
  parisc/PCI: factor out pcibios_setup()
  MIPS/PCI: adjust section annotations for pcibios_setup()
  MIPS/PCI: factor out pcibios_setup()
  microblaze/PCI: factor out pcibios_setup()
  ia64/PCI: factor out pcibios_setup()
  cris/PCI: factor out pcibios_setup()
  alpha/PCI: factor out pcibios_setup()
  PCI: pull pcibios_setup() up into core

Currently, all of the architectures implement their own pcibios_setup()
routine.  Most of the implementations do nothing so this patch introduces
a generic (__weak) routine in the core that can be used by all
architectures as a default.  If necessary, it can be overridden by
architecture-specific code.

Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* topic/huang-d3cold-v7:
  PCI/PM: add PCIe runtime D3cold support
  PCI: do not call pci_set_power_state with PCI_D3cold
  PCI/PM: add runtime PM support to PCIe port
  ACPI/PM: specify lowest allowed state for device sleep state

This patch adds runtime D3cold support and corresponding ACPI platform
support.  This patch only enables runtime D3cold support; it does not
enable D3cold support during system suspend/hibernate.

D3cold is the deepest power saving state for a PCIe device, where its main
power is removed.  While it is in D3cold, you can't access the device at
all, not even its configuration space (which is still accessible in D3hot).
Therefore the PCI PM registers can not be used to transition into/out of
the D3cold state; that must be done by platform logic such as ACPI _PR3.

To support wakeup from D3cold, a system may provide auxiliary power, which
allows a device to request wakeup using a Beacon or the sideband WAKE#
signal.  WAKE# is usually connected to platform logic such as ACPI GPE.
This is quite different from other power saving states, where devices
request wakeup via a PME message on the PCIe link.

Some devices, such as those in plug-in slots, have no direct platform
logic.  For example, there is usually no ACPI _PR3 for them.  D3cold
support for these devices can be done via the PCIe Downstream Port leading
to the device.  When the PCIe port is powered on/off, the device is powered
on/off too.  Wakeup events from the device will be notified to the
corresponding PCIe port.

For more information about PCIe D3cold and corresponding ACPI support,
please refer to:

- PCI Express Base Specification Revision 2.0
- Advanced Configuration and Power Interface Specification Revision 5.0

[bhelgaas: changelog]
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Originally-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* topic/jan-intx-masking:
  PCI: add Ralink RT2800 broken INTx masking quirk
  PCI: add Chelsio T310 10GbE NIC broken INTx masking quirk
  PCI: add infrastructure for devices with broken INTx masking

* topic/stowe-cap-cleanup:
  PCI: remove redundant capabilities checking in pci_{save, restore}_pcie_state
  PCI: add pci_pcie_cap2() check for PCIe feature capabilities >= v2
  PCI: remove redundant checking in PCI Express capability routines
  PCI: make pci_ltr_supported() static

pci_intx_mask_supported() assumes INTx masking is supported if the
PCI_COMMAND_INTX_DISABLE bit is writable.  But when that bit is set,
some devices don't actually mask INTx or update PCI_STATUS_INTERRUPT
as we expect.

This patch adds a way for quirks to identify these broken devices.

[bhelgaas: split out from Chelsio quirk addition]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* topic/alex-vfio-prep:
  PCI: misc pci_reg additions
  PCI: create common pcibios_err_to_errno
  PCI: export pci_user functions for use by other drivers
  PCI: add ACS validation utility
  PCI: add PCI DMA source ID quirk