Tested with ATO AFND1G08U3, 128MiB NAND.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>

read_page_raw and write_page_raw method description is not clear enough.
It clearly specifies that ECC correction should not be involved but does
not talk about specific layout (by layout I mean where in-band and
out-of-band data are stored on the NAND media) used by NAND/ECC
controllers.

Those specific layouts might impact MTD users and thus should be hidden (as
already done in the standard NAND_ECC_HW_SYNDROME implementation).

Clearly state this constraint in the nand_ecc_ctrl struct documentation.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add an onfi_timing_mode_default field to nand_chip and nand_flash_dev in
order to support NAND timings definition for non-ONFI NAND.

NAND that support better timings mode than the default one have to define
a new entry in the nand_ids table.

The default timing mode should be deduced from timings description from
the datasheet and the ONFI specification
(www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf, chapter 4.15
"Timing Parameters").
You should choose the closest mode that fit the timings requirements of
your NAND chip.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Change the comment type (from /** to /*) to prevent DocBook from
complaining about missing description for nand_sdr_timings fields.

There is currently no need in documenting those fields because they are
fully described in the ONFI specification (which is pointed out in the
comment).

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Fix kernel-doc warning in <linux/mtd/nand.h>:

Warning(..//include/linux/mtd/nand.h:795): No description found for parameter 'ecc'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc:	David Woodhouse <dwmw2@infradead.org>
Cc:	Brian Norris <computersforpeace@gmail.com>
Cc:	linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add a converter to retrieve NAND timings from an ONFI NAND timing mode.
At the moment, only SDR NAND timings are supported.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Define a struct containing the standard NAND timings as described in NAND
datasheets.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().

While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

nand_base can be passed a kmap()'d buffers from highmem by
filesystems like jffs2. This results in failure to map the
physical address of the DMA buffer on various contoller
driver on different platforms. This change adds a chip option
to use preallocated databuf as bounce buffers used in
nand_do_read_ops() and nand_do_write_ops().
This allows for specific nand controller driver to set this
option as needed.

Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>