Pull ARM SoC driver updates from Olof Johansson:
 "Various driver updates for platforms:

   - A larger set of work on Tegra 2/3 around memory controller and
     regulator features, some fuse cleanups, etc..

   - MMP platform drivers, in particular for USB PHY, and other smaller
     additions.

   - Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
     and ASV (adaptive voltage), allowing the platform to run at more
     optimal operating points.

   - Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas

   - Clock/reset control driver for TI/OMAP

   - Meson-A1 reset controller support

   - Qualcomm sdm845 and sda845 SoC IDs for socinfo"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
  firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
  soc: fsl: add RCPM driver
  dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
  memory: tegra: Consolidate registers definition into common header
  memory: tegra: Ensure timing control debug features are disabled
  memory: tegra: Introduce Tegra30 EMC driver
  memory: tegra: Do not handle error from wait_for_completion_timeout()
  memory: tegra: Increase handshake timeout on Tegra20
  memory: tegra: Print a brief info message about EMC timings
  memory: tegra: Pre-configure debug register on Tegra20
  memory: tegra: Include io.h instead of iopoll.h
  memory: tegra: Adapt for Tegra20 clock driver changes
  memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
  memory: tegra: Add gr2d and gr3d to DRM IOMMU group
  memory: tegra: Set DMA mask based on supported address bits
  soc: at91: Add Atmel SFR SN (Serial Number) support
  memory: atmel-ebi: switch to SPDX license identifiers
  memory: atmel-ebi: move NUM_CS definition inside EBI driver
  soc: mediatek: Refactor bus protection control
  soc: mediatek: Refactor sram control
  ...

Pull char/misc driver updates from Greg KH:
 "Here is the big set of char/misc and other driver patches for 5.5-rc1

  Loads of different things in here, this feels like the catch-all of
  driver subsystems these days. Full details are in the shortlog, but
  nothing major overall, just lots of driver updates and additions.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
  char: Fix Kconfig indentation, continued
  habanalabs: add more protection of device during reset
  habanalabs: flush EQ workers in hard reset
  habanalabs: make the reset code more consistent
  habanalabs: expose reset counters via existing INFO IOCTL
  habanalabs: make code more concise
  habanalabs: use defines for F/W files
  habanalabs: remove prints on successful device initialization
  habanalabs: remove unnecessary checks
  habanalabs: invalidate MMU cache only once
  habanalabs: skip VA block list update in reset flow
  habanalabs: optimize MMU unmap
  habanalabs: prevent read/write from/to the device during hard reset
  habanalabs: split MMU properties to PCI/DRAM
  habanalabs: re-factor MMU masks and documentation
  habanalabs: type specific MMU cache invalidation
  habanalabs: re-factor memory module code
  habanalabs: export uapi defines to user-space
  habanalabs: don't print error when queues are full
  habanalabs: increase max jobs number to 512
  ...

Pull MMC updates from Ulf Hansson:
 "These are the updates for MMC and MEMSTICK for v5.5.

  Note that this also contains quite some additional changes reaching
  beyond both the MMC and MEMSTICK subsystems. This is primarily because
  of fixing an old regression for a WiFi driver based on the SDIO
  interface on an OMAP openpandora board

  MMC core:
   - Add CMD13 polling for MMC IOCTLS with R1B response.
   - Add common DT properties for clk-phase-delays for various speed
     modes.
   - Fix size overflow for mmc gp-partitions.
   - Re-work HW reset for SDIO cards, which also includes a re-work for
     Marvell's WiFi mwifiex SDIO func driver.

  MMC host:
   - jz4740: Add support for X1000 and JZ4760.
   - jz4740: Add support for 8-bit bus and for low power mode.
   - mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
   - owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
   - renesas_sdhi: Add support for r8a774b1.
   - sdhci_am654: Add support for Command Queuing Engine for J721E.
   - sdhci-milbeaut: Add driver for the Milbeaut SD controller.
   - sdhci-of-arasan: Add support for ZynqMP tap-delays.
   - sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
   - sdhci-of-arasan: Add support for Intel LGM SDXC.
   - sdhci-of-aspeed: Allow inversion of the internal card detect
     signal.
   - sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
   - sdhci-of-at91: Improve support for calibration.
   - sdhci-pci: Add support for Intel JSL.
   - sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
   - tmio: Enable support for erase/discard/trim requests.

  MMC/OMAP/pandora/wl1251:

  The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has
  been broken since v4.7. To fix the problems, changes have been made
  cross subsystems, but also to OMAP2 machine code and to openpandora
  DTS files, as summarized below. Relevant changes have been tagged for
  stable.

   - mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
   - omap/omap_hsmmc: Remove redundant platform config for openpandora
   - omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
   - omap/dts/pandora: Specify wl1251 through a child node of mmc3
   - wl1251: Add devicetree support for TI wl1251 SDIO"

* tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits)
  dt-bindings: mmc: Correct the type of the clk phase properties
  Revert "mmc: tmio: remove workaround for NON_REMOVABLE"
  memstick: Fix Kconfig indentation
  mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup
  dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller
  firmware: xilinx: Add SDIO Tap Delay nodes
  mmc: sdhci-of-arasan: Add support to set clock phase delays for SD
  dt-bindings: mmc: Add optional generic properties for mmc
  mmc: sdhci-of-arasan: Add sampling clock for a phy to use
  dt-bindings: mmc: arasan: Update Documentation for the input clock
  mmc: sdhci-of-arasan: Separate out clk related data to another structure
  mmc: sdhci: Fix grammar in warning message
  mmc: sdhci-of-aspeed: add inversion signal presence
  mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS
  mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E
  mmc: core: Fix size overflow for mmc partitions
  mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests
  net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions
  net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition
  mmc: core: fix wl1251 sdio quirks
  ...

Add tap delay nodes for setting SDIO Tap Delays on ZynqMP platform.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The older versions of remote system update (RSU) firmware don't support
retry and notify features then the kernel module dies when it queries
the RSU retry counter or performs notify operation.

Update the Intel service layer and RSU drivers to be compatible with
all versions of RSU firmware.

Reported-by: Radu Barcau <radu.bacrau@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Richard Gong <richard.gong@intel.com>
Link: https://lore.kernel.org/r/1572884676-1385-1-git-send-email-richard.gong@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

soc: amlogic: updates for v5.5

Highlights
- socinfo: more SoC IDs
- firmware: misc secure-monitor cleanups

* tag 'amlogic-drivers' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  soc: amlogic: meson-gx-socinfo: Fix S905D3 ID for VIM3L
  soc: amlogic: meson-gx-socinfo: Add S905X3 ID for VIM3L
  soc: amlogic: meson-gx-socinfo: Add A1 and A113L IDs
  firmware: meson_sm: use %*ph to print small buffer
  firmware: meson_sm: Rework driver as a proper platform driver
  nvmem: meson-efuse: bindings: Add secure-monitor phandle
  firmware: meson_sm: Mark chip struct as static const

Link: https://lore.kernel.org/r/7hftivs11f.fsf@baylibre.com
Signed-off-by: Olof Johansson <olof@lixom.net>

This driver registers on TEE bus to interact with OP-TEE based
BNXT firmware management modules

Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For "0" requirement which is used to inform firmware that device is
not required currently by master, Versal PLM (Platform Loader and
Manager) which runs on Platform Management Controller and is responsible
platform management of devices that disables clock, power it down
and reset the device. genpd_power_off() is being called during runtime
suspend also. So, if any device goes to runtime suspend state during
resumes it needs to be re-initialized again. It is possible that
drivers do not reinitialize device upon resume from runtime suspend
every time ans so dont want it to be powered down or get reset
during runtime suspend.

In Versal PLM new PM_CAP_UNUSABLE capability is added, which disables
clock only and avoids power down and reset during runtime suspend. Power
and reset will be gated with core suspend.So, this patch sets
CAPABILITY_UNUSABLE requirement during gpd_power_off()
if platform is other than zynqmp.

Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The secure monitor driver is currently a frankenstein driver which is
registered as a platform driver but its functionality goes through a
global struct accessed by the consumer drivers using exported helper
functions.

Try to tidy up the driver moving the firmware struct into the driver
data and make the consumer drivers referencing the secure-monitor using
a new property in the DT.

Currently only the nvmem driver is using this API so we can fix it in
the same commit.

Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Pull char/misc driver updates from Greg KH:
 "Here is the big char/misc driver pull request for 5.4-rc1.

  As has been happening in previous releases, more and more individual
  driver subsystem trees are ending up in here. Now if that is good or
  bad I can't tell, but hopefully it makes your life easier as it's more
  of an aggregation of trees together to one merge point for you.

  Anyway, lots of stuff in here:
     - habanalabs driver updates
     - thunderbolt driver updates
     - misc driver updates
     - coresight and intel_th hwtracing driver updates
     - fpga driver updates
     - extcon driver updates
     - some dma driver updates
     - char driver updates
     - android binder driver updates
     - nvmem driver updates
     - phy driver updates
     - parport driver fixes
     - pcmcia driver fix
     - uio driver updates
     - w1 driver updates
     - configfs fixes
     - other assorted driver updates

  All of these have been in linux-next for a long time with no reported
  issues"

* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (200 commits)
  misc: mic: Use PTR_ERR_OR_ZERO rather than its implementation
  habanalabs: correctly cast variable to __le32
  habanalabs: show correct id in error print
  habanalabs: stop using the acronym KMD
  habanalabs: display card name as sensors header
  habanalabs: add uapi to retrieve aggregate H/W events
  habanalabs: add uapi to retrieve device utilization
  habanalabs: Make the Coresight timestamp perpetual
  habanalabs: explicitly set the queue-id enumerated numbers
  habanalabs: print to kernel log when reset is finished
  habanalabs: replace __le32_to_cpu with le32_to_cpu
  habanalabs: replace __cpu_to_le32/64 with cpu_to_le32/64
  habanalabs: Handle HW_IP_INFO if device disabled or in reset
  habanalabs: Expose devices after initialization is done
  habanalabs: improve security in Debug IOCTL
  habanalabs: use default structure for user input in Debug IOCTL
  habanalabs: Add descriptive name to PSOC app status register
  habanalabs: Add descriptive names to PSOC scratch-pad registers
  habanalabs: create two char devices per ASIC
  habanalabs: change device_setup_cdev() to be more generic
  ...