Pull i2c updates from Wolfram Sang:
 "Highlights:

   - class based instantiation finally dropped for most embedded drivers
     bringing boot up performance gains
   - removed two drivers (one outdated, one a duplicate)
   - ACPI has now operation region support (thanks to Lan Tianyu)
   - the i2c-stub driver got overhauled and gained new features to
     become more useful when writing i2c client drivers (thanks to
     Guenter Roeck and Jean Delvare)

  The rest is driver bugfixes, added bindings/ids, cleanups..."

* 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
  i2c: mpc: delete unneeded test before of_node_put
  i2c: rk3x: fix interrupt handling issue
  i2c: imx: Fix format warning for dev_dbg
  i2c: qup: disable clks and return instead of just returning error
  i2c: exynos5: always enable HSI2C
  i2c: designware: add new bindings
  i2c: gpio: Drop dead code in i2c_gpio_remove
  i2c: pca954x: put the mux to disconnected state after resume
  i2c: st: Update i2c timings
  drivers/i2c/busses: use correct type for dma_map/unmap
  i2c: i2c-st: Use %pa to print 'resource_size_t' type
  i2c: s3c2410: resume the I2C controller earlier
  i2c: stub: Avoid an array overrun on I2C block transfers
  i2c: i801: Add device ID for Intel Wildcat Point PCH
  i2c: i801: Fix the alignment of the device table
  i2c: stub: Add support for banked register ranges
  i2c: stub: Remember the number of emulated chips
  i2c: stub: Add support for SMBus block commands
  i2c: efm32: correct namespacing of location property
  i2c: exynos5: remove extra line and fix an assignment
  ...

This patch moves <acpi/acpi.h> out of CONFIG_ACPI condition so that all
ACPICA prototypes can be seen by the CONFIG_ACPI=n Linux kernel builds.
Note that we can do this because ACPICA has implemented stubs for all
ACPICA prototypes that are currently referenced by the Linux kernel.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPI 5.0 spec(5.5.2.4.5) defines GenericSerialBus(i2c, spi, uart) operation region.
It allows ACPI aml code able to access such kind of devices to implement
some ACPI standard method.

ACPI Spec defines some access attribute to associate with i2c protocol.
AttribQuick 	       	       		Read/Write Quick Protocol
AttribSendReceive			Send/Receive Byte Protocol
AttribByte 			 	Read/Write Byte Protocol
AttribWord				Read/Write Word Protocol
AttribBlock				Read/Write Block Protocol
AttribBytes				Read/Write N-Bytes Protocol
AttribProcessCall			Process Call Protocol
AttribBlockProcessCall			Write Block-Read Block Process Call Protocol
AttribRawBytes 				Raw Read/Write N-BytesProtocol
AttribRawProcessBytes			Raw Process Call Protocol

On the Asus T100TA, Bios use GenericSerialBus operation region to access
i2c device to get battery info.

Sample code From Asus T100TA

    Scope (_SB.I2C1)
    {
        Name (UMPC, ResourceTemplate ()
        {
            I2cSerialBus (0x0066, ControllerInitiated, 0x00061A80,
                AddressingMode7Bit, "\\_SB.I2C1",
                0x00, ResourceConsumer, ,
                )
        })

	...

        OperationRegion (DVUM, GenericSerialBus, Zero, 0x0100)
        Field (DVUM, BufferAcc, NoLock, Preserve)
        {
            Connection (UMPC),
            Offset (0x81),
            AccessAs (BufferAcc, AttribBytes (0x3E)),
            FGC0,   8
        }
	...
     }

     Device (BATC)
     {
         Name (_HID, EisaId ("PNP0C0A"))  // _HID: Hardware ID
         Name (_UID, One)  // _UID: Unique ID
	 ...

            Method (_BST, 0, NotSerialized)  // _BST: Battery Status
            {
                If (LEqual (AVBL, One))
                {
                    Store (FGC0, BFFG)
                    If (LNotEqual (STAT, One))
                    {
                        ShiftRight (CHST, 0x04, Local0)
                        And (Local0, 0x03, Local0)
                        If (LOr (LEqual (Local0, One), LEqual (Local0, 0x02)))
                        {
                            Store (0x02, Local1)
                        }
	...

    }

The i2c operation region is defined under I2C1 scope. _BST method under
battery device BATC read battery status from the field "FCG0". The request
would be sent to i2c operation region handler.

This patch is to add i2c ACPI operation region support. Due to there are
only "Byte" and "Bytes" protocol access on the Asus T100TA, other protocols
have not been tested.

About RawBytes and RawProcessBytes protocol, they needs specific drivers to interpret
reference data from AML code according ACPI 5.0 SPEC(5.5.2.4.5.3.9 and 5.5.2.4.5.3.10).
So far, not found such case and will add when find real case.

Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

* acpi-enumeration:
  ACPI / scan: use platform bus type by default for _HID enumeration
  ACPI / scan: always register ACPI LPSS scan handler
  ACPI / scan: always register memory hotplug scan handler
  ACPI / scan: always register container scan handler
  ACPI / scan: Change the meaning of missing .attach() in scan handlers
  ACPI / scan: introduce platform_id device PNP type flag
  ACPI / scan: drop unsupported serial IDs from PNP ACPI scan handler ID list
  ACPI / scan: drop IDs that do not comply with the ACPI PNP ID rule
  ACPI / PNP: use device ID list for PNPACPI device enumeration
  ACPI / scan: .match() callback for ACPI scan handlers

* acpi-pm:
  ACPI / PM: Export rest of the subsys PM callbacks
  ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend
  ACPI / PM: Hold ACPI scan lock over the "freeze" sleep state
  ACPI / PM: Export acpi_target_system_state() to modules

ACPI can be used to enumerate PNP devices, but the code does not
handle this in the right way currently.  Namely, if an ACPI device
object
 1. Has a _CRS method,
 2. Has an identification of
    "three capital characters followed by four hex digits",
 3. Is not in the excluded IDs list,
it will be enumerated to PNP bus (that is, a PNP device object will
be create for it).  This means that, actually, the PNP bus type is
used as the default bus type for enumerating _HID devices in ACPI.

However, more and more _HID devices need to be enumerated to the
platform bus instead (that is, platform device objects need to be
created for them).  As a result, the device ID list in acpi_platform.c
is used to enforce creating platform device objects rather than PNP
device objects for matching devices.  That list has been continuously
growing recently, unfortunately, and it is pretty much guaranteed to
grow even more in the future.

To address that problem it is better to enumerate _HID devices
as platform devices by default.  To this end, change the way of
enumerating PNP devices by adding a PNP ACPI scan handler that
will use a device ID list to create PNP devices for the ACPI
device objects whose device IDs are present in that list.

The initial device ID list in the PNP ACPI scan handler contains
all of the pnp_device_id strings from all the existing PNP drivers,
so this change should be transparent to the PNP core and all of the
PNP drivers.  Still, in the future it should be possible to reduce
its size by converting PNP drivers that need not be PNP for any
technical reasons into platform drivers.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[rjw: Rewrote the changelog, modified the PNP ACPI scan handler code]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Commit 1a699476e258 ("ACPI / hotplug / PCI: Hotplug notifications
from acpi_bus_notify()") added debug messages for a few common
events. These debug messages are unconditionally enabled if
CONFIG_DYNAMIC_DEBUG is defined, contrary to the documented
meaning, making the ACPI system spew lots of unwanted noise on
any kernel with dynamic debugging.

The bug was introduced by commit fbfddae69657 ("ACPI: Add
acpi_handle_<level>() interfaces"), which added the
CONFIG_DYNAMIC_DEBUG dependency without respecting its meaning.

Fix by adding real support for dynamic_debug.

Fixes: fbfddae69657 ("ACPI: Add acpi_handle_<level>() interfaces")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

No reason for excluding the remaining ones.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[rjw: Rebased and exported the new acpi_subsys_complete() too.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull PCI changes from Bjorn Helgaas:
 "Enumeration
   - Increment max correctly in pci_scan_bridge() (Andreas Noever)
   - Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
   - Assign CardBus bus number only during the second pass (Andreas Noever)
   - Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
   - Make sure bus number resources stay within their parents bounds (Andreas Noever)
   - Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
   - Check for child busses which use more bus numbers than allocated (Andreas Noever)
   - Don't scan random busses in pci_scan_bridge() (Andreas Noever)
   - x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
   - x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
   - x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
   - x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
   - x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)

  NUMA
   - x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
   - x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
   - x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
   - x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
   - x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
   - ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
   - ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
   - ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)

  Resource management
   - i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
   - Add resource_contains() (Bjorn Helgaas)
   - Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
   - Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
   - Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
   - Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
   - Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
   - Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
   - Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
   - Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
   - alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
   - s390: Use generic pci_enable_resources() (Bjorn Helgaas)
   - Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
   - Set type in __request_region() (Bjorn Helgaas)
   - Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
   - Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
   - Log IDE resource quirk in dmesg (Bjorn Helgaas)
   - Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)

  PCI device hotplug
   - Make check_link_active() non-static (Rajat Jain)
   - Use link change notifications for hot-plug and removal (Rajat Jain)
   - Enable link state change notifications (Rajat Jain)
   - Don't disable the link permanently during removal (Rajat Jain)
   - Don't check adapter or latch status while disabling (Rajat Jain)
   - Disable link notification across slot reset (Rajat Jain)
   - Ensure very fast hotplug events are also processed (Rajat Jain)
   - Add hotplug_lock to serialize hotplug events (Rajat Jain)
   - Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
   - Don't turn slot off when hot-added device already exists (Yijing Wang)

  MSI
   - Keep pci_enable_msi() documentation (Alexander Gordeev)
   - ahci: Fix broken single MSI fallback (Alexander Gordeev)
   - ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
   - Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
   - Fix leak of msi_attrs (Greg Kroah-Hartman)
   - Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)

  Virtualization
   - Device-specific ACS support (Alex Williamson)

  Freescale i.MX6
   - Wait for retraining (Marek Vasut)

  Marvell MVEBU
   - Use Device ID and revision from underlying endpoint (Andrew Lunn)
   - Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
   - Call request_resource() on the apertures (Jason Gunthorpe)
   - Fix potential issue in range parsing (Jean-Jacques Hiblot)

  Renesas R-Car
   - Check platform_get_irq() return code (Ben Dooks)
   - Add error interrupt handling (Ben Dooks)
   - Fix bridge logic configuration accesses (Ben Dooks)
   - Register each instance independently (Magnus Damm)
   - Break out window size handling (Magnus Damm)
   - Make the Kconfig dependencies more generic (Magnus Damm)

  Synopsys DesignWare
   - Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)

  Miscellaneous
   - Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
   - Enable INTx if BIOS left them disabled (Bjorn Helgaas)
   - Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
   - Clean up par-arch object file list (Liviu Dudau)
   - Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
   - ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
   - Fix pci_bus_b() build failure (Paul Gortmaker)"

* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
  Revert "[PATCH] Insert GART region into resource map"
  PCI: Log IDE resource quirk in dmesg
  PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
  PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
  resources: Set type in __request_region()
  PCI: Don't check resource_size() in pci_bus_alloc_resource()
  s390/PCI: Use generic pci_enable_resources()
  tile PCI RC: Use default pcibios_enable_device()
  sparc/PCI: Use default pcibios_enable_device() (Leon only)
  sh/PCI: Use default pcibios_enable_device()
  microblaze/PCI: Use default pcibios_enable_device()
  alpha/PCI: Use default pcibios_enable_device()
  PCI: Add "weak" generic pcibios_enable_device() implementation
  PCI: Don't enable decoding if BAR hasn't been assigned an address
  PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
  PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
  PCI: Don't try to claim IORESOURCE_UNSET resources
  PCI: Check IORESOURCE_UNSET before updating BAR
  PCI: Don't clear IORESOURCE_UNSET when updating BAR
  PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
  ...

Conflicts:
	arch/x86/include/asm/topology.h
	drivers/ata/ahci.c

BAD_MADT_ENTRY() is arch independent and will be used for all
architectures which parse MADT, so move it to linux/acpi.h to
reduce code duplication.

Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>