[ Upstream commit 6212e4528b248a4bc9b4fe68e029a84689c67461 ]

In case of an final DLM message we can't should not send an ack out
after the final message. This patch moves the ack message before the
messages will be transmitted. If it's the final message and the
receiving node turns into DLM_CLOSED state another ack messages will
being received and turning the receiving node into DLM_ESTABLISHED
again.

Fixes: 1696c75f1864 ("fs: dlm: add send ack threshold and append acks to msgs")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 7c53e847ff5e97f033fdd31f71949807633d506b upstream.

All posix lock ops, for all lockspaces (gfs2 file systems) are
sent to userspace (dlm_controld) through a single misc device.
The dlm_controld daemon reads the ops from the misc device
and sends them to other cluster nodes using separate, per-lockspace
cluster api communication channels.  The ops for a single lockspace
are ordered at this level, so that the results are received in
the same sequence that the requests were sent.  When the results
are sent back to the kernel via the misc device, they are again
funneled through the single misc device for all lockspaces.  When
the dlm code in the kernel processes the results from the misc
device, these results will be returned in the same sequence that
the requests were sent, on a per-lockspace basis.  A recent change
in this request/reply matching code missed the "per-lockspace"
check (fsid comparison) when matching request and reply, so replies
could be incorrectly matched to requests from other lockspaces.

Cc: stable@vger.kernel.org
Reported-by: Barry Marson <bmarson@redhat.com>
Fixes: 57e2c2f2d94c ("fs: dlm: fix mismatch of plock results from userspace")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull dlm updates from David Teigland:
 "The dlm posix lock handling (for gfs2) has three notable changes:

   - Local pids returned from GETLK are no longer negated. A previous
     patch negating remote pids mistakenly changed local pids also.

   - SETLKW operations can now be interrupted only when the process is
     killed, and not from other signals. General interruption was
     resulting in previously acquired locks being cleared, not just the
     in-progress lock. Handling this correctly will require extending a
     cancel capability to user space (a future feature.)

   - If multiple threads are requesting posix locks (with SETLKW), fix
     incorrect matching of results to the requests.

  The dlm networking has several minor cleanups, and one notable change:

   - Avoid delaying ack messages for too long (used for message
     reliability), resulting in a backlog of un-acked messages. These
     could previously be delayed as a result of either too many or too
     few other messages being sent. Now an upper and lower threshold is
     used to determine when an ack should be sent"

* tag 'dlm-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
  fs: dlm: remove filter local comms on close
  fs: dlm: add send ack threshold and append acks to msgs
  fs: dlm: handle sequence numbers as atomic
  fs: dlm: handle lkb wait count as atomic_t
  fs: dlm: filter ourself midcomms calls
  fs: dlm: warn about messages from left nodes
  fs: dlm: move dlm_purge_lkb_callbacks to user module
  fs: dlm: cleanup STOP_IO bitflag set when stop io
  fs: dlm: don't check othercon twice
  fs: dlm: unregister memory at the very last
  fs: dlm: fix missing pending to false
  fs: dlm: clear pending bit when queue was empty
  fs: dlm: revert check required context while close
  fs: dlm: fix mismatch of plock results from userspace
  fs: dlm: make F_SETLK use unkillable wait_event
  fs: dlm: interrupt posix locks only when process is killed
  fs: dlm: fix cleanup pending ops when interrupted
  fs: dlm: return positive pid value for F_GETLK
  dlm: Replace all non-returning strlcpy with strscpy

Pull networking changes from Jakub Kicinski:
 "WiFi 7 and sendpage changes are the biggest pieces of work for this
  release. The latter will definitely require fixes but I think that we
  got it to a reasonable point.

  Core:

   - Rework the sendpage & splice implementations

     Instead of feeding data into sockets page by page extend sendmsg
     handlers to support taking a reference on the data, controlled by a
     new flag called MSG_SPLICE_PAGES

     Rework the handling of unexpected-end-of-file to invoke an
     additional callback instead of trying to predict what the right
     combination of MORE/NOTLAST flags is

     Remove the MSG_SENDPAGE_NOTLAST flag completely

   - Implement SCM_PIDFD, a new type of CMSG type analogous to
     SCM_CREDENTIALS, but it contains pidfd instead of plain pid

   - Enable socket busy polling with CONFIG_RT

   - Improve reliability and efficiency of reporting for ref_tracker

   - Auto-generate a user space C library for various Netlink families

  Protocols:

   - Allow TCP to shrink the advertised window when necessary, prevent
     sk_rcvbuf auto-tuning from growing the window all the way up to
     tcp_rmem[2]

   - Use per-VMA locking for "page-flipping" TCP receive zerocopy

   - Prepare TCP for device-to-device data transfers, by making sure
     that payloads are always attached to skbs as page frags

   - Make the backoff time for the first N TCP SYN retransmissions
     linear. Exponential backoff is unnecessarily conservative

   - Create a new MPTCP getsockopt to retrieve all info
     (MPTCP_FULL_INFO)

   - Avoid waking up applications using TLS sockets until we have a full
     record

   - Allow using kernel memory for protocol ioctl callbacks, paving the
     way to issuing ioctls over io_uring

   - Add nolocalbypass option to VxLAN, forcing packets to be fully
     encapsulated even if they are destined for a local IP address

   - Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
     in-kernel ECMP implementation (e.g. Open vSwitch) select the same
     link for all packets. Support L4 symmetric hashing in Open vSwitch

   - PPPoE: make number of hash bits configurable

   - Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
     (ipconfig)

   - Add layer 2 miss indication and filtering, allowing higher layers
     (e.g. ACL filters) to make forwarding decisions based on whether
     packet matched forwarding state in lower devices (bridge)

   - Support matching on Connectivity Fault Management (CFM) packets

   - Hide the "link becomes ready" IPv6 messages by demoting their
     printk level to debug

   - HSR: don't enable promiscuous mode if device offloads the proto

   - Support active scanning in IEEE 802.15.4

   - Continue work on Multi-Link Operation for WiFi 7

  BPF:

   - Add precision propagation for subprogs and callbacks. This allows
     maintaining verification efficiency when subprograms are used, or
     in fact passing the verifier at all for complex programs,
     especially those using open-coded iterators

   - Improve BPF's {g,s}setsockopt() length handling. Previously BPF
     assumed the length is always equal to the amount of written data.
     But some protos allow passing a NULL buffer to discover what the
     output buffer *should* be, without writing anything

   - Accept dynptr memory as memory arguments passed to helpers

   - Add routing table ID to bpf_fib_lookup BPF helper

   - Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands

   - Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
     maps as read-only)

   - Show target_{obj,btf}_id in tracing link fdinfo

   - Addition of several new kfuncs (most of the names are
     self-explanatory):
      - Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
        bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
        and bpf_dynptr_clone().
      - bpf_task_under_cgroup()
      - bpf_sock_destroy() - force closing sockets
      - bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs

  Netfilter:

   - Relax set/map validation checks in nf_tables. Allow checking
     presence of an entry in a map without using the value

   - Increase ip_vs_conn_tab_bits range for 64BIT builds

   - Allow updating size of a set

   - Improve NAT tuple selection when connection is closing

  Driver API:

   - Integrate netdev with LED subsystem, to allow configuring HW
     "offloaded" blinking of LEDs based on link state and activity
     (i.e. packets coming in and out)

   - Support configuring rate selection pins of SFP modules

   - Factor Clause 73 auto-negotiation code out of the drivers, provide
     common helper routines

   - Add more fool-proof helpers for managing lifetime of MDIO devices
     associated with the PCS layer

   - Allow drivers to report advanced statistics related to Time Aware
     scheduler offload (taprio)

   - Allow opting out of VF statistics in link dump, to allow more VFs
     to fit into the message

   - Split devlink instance and devlink port operations

  New hardware / drivers:

   - Ethernet:
      - Synopsys EMAC4 IP support (stmmac)
      - Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
      - Marvell 88E6250 7 port switches
      - Microchip LAN8650/1 Rev.B0 PHYs
      - MediaTek MT7981/MT7988 built-in 1GE PHY driver

   - WiFi:
      - Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
      - Realtek RTL8723DS (SDIO variant)
      - Realtek RTL8851BE

   - CAN:
      - Fintek F81604

  Drivers:

   - Ethernet NICs:
      - Intel (100G, ice):
         - support dynamic interrupt allocation
         - use meta data match instead of VF MAC addr on slow-path
      - nVidia/Mellanox:
         - extend link aggregation to handle 4, rather than just 2 ports
         - spawn sub-functions without any features by default
      - OcteonTX2:
         - support HTB (Tx scheduling/QoS) offload
         - make RSS hash generation configurable
         - support selecting Rx queue using TC filters
      - Wangxun (ngbe/txgbe):
         - add basic Tx/Rx packet offloads
         - add phylink support (SFP/PCS control)
      - Freescale/NXP (enetc):
         - report TAPRIO packet statistics
      - Solarflare/AMD:
         - support matching on IP ToS and UDP source port of outer
           header
         - VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
         - add devlink dev info support for EF10

   - Virtual NICs:
      - Microsoft vNIC:
         - size the Rx indirection table based on requested
           configuration
         - support VLAN tagging
      - Amazon vNIC:
         - try to reuse Rx buffers if not fully consumed, useful for ARM
           servers running with 16kB pages
      - Google vNIC:
         - support TCP segmentation of >64kB frames

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - enable USXGMII (88E6191X)
      - Microchip:
         - lan966x: add support for Egress Stage 0 ACL engine
         - lan966x: support mapping packet priority to internal switch
           priority (based on PCP or DSCP)

   - Ethernet PHYs:
      - Broadcom PHYs:
         - support for Wake-on-LAN for BCM54210E/B50212E
         - report LPI counter
      - Microsemi PHYs: support RGMII delay configuration (VSC85xx)
      - Micrel PHYs: receive timestamp in the frame (LAN8841)
      - Realtek PHYs: support optional external PHY clock
      - Altera TSE PCS: merge the driver into Lynx PCS which it is a
        variant of

   - CAN: Kvaser PCIEcan:
      - support packet timestamping

   - WiFi:
      - Intel (iwlwifi):
         - major update for new firmware and Multi-Link Operation (MLO)
         - configuration rework to drop test devices and split the
           different families
         - support for segmented PNVM images and power tables
         - new vendor entries for PPAG (platform antenna gain) feature
      - Qualcomm 802.11ax (ath11k):
         - Multiple Basic Service Set Identifier (MBSSID) and Enhanced
           MBSSID Advertisement (EMA) support in AP mode
         - support factory test mode
      - RealTek (rtw89):
         - add RSSI based antenna diversity
         - support U-NII-4 channels on 5 GHz band
      - RealTek (rtl8xxxu):
         - AP mode support for 8188f
         - support USB RX aggregation for the newer chips"

* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
  net: scm: introduce and use scm_recv_unix helper
  af_unix: Skip SCM_PIDFD if scm->pid is NULL.
  net: lan743x: Simplify comparison
  netlink: Add __sock_i_ino() for __netlink_diag_dump().
  net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
  Revert "af_unix: Call scm_recv() only after scm_set_cred()."
  phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
  libceph: Partially revert changes to support MSG_SPLICE_PAGES
  net: phy: mscc: fix packet loss due to RGMII delays
  net: mana: use vmalloc_array and vcalloc
  net: enetc: use vmalloc_array and vcalloc
  ionic: use vmalloc_array and vcalloc
  pds_core: use vmalloc_array and vcalloc
  gve: use vmalloc_array and vcalloc
  octeon_ep: use vmalloc_array and vcalloc
  net: usb: qmi_wwan: add u-blox 0x1312 composition
  perf trace: fix MSG_SPLICE_PAGES build error
  ipvlan: Fix return value of ipvlan_queue_xmit()
  netfilter: nf_tables: fix underflow in chain reference counter
  netfilter: nf_tables: unbind non-anonymous set if rule construction fails
  ...

When transmitting data, call down a layer using a single sendmsg with
MSG_SPLICE_PAGES to indicate that content should be spliced rather using
sendpage.  This allows ->sendpage() to be replaced by something that can
handle multiple multipage folios in a single transaction.

Signed-off-by: David Howells <dhowells@redhat.com>
cc: Christine Caulfield <ccaulfie@redhat.com>
cc: David Teigland <teigland@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: cluster-devel@redhat.com
Link: https://lore.kernel.org/r/20230623225513.2732256-7-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The current way how lowcomms is configured is due configfs entries. Each
comms configfs entry will create a lowcomms connection. Even the local
connection itself will be stored as a lowcomms connection, although most
functionality for a local lowcomms connection struct is not necessary.

Now in some scenarios we will see that dlm_controld reports a -EEXIST
when configure a node via configfs:

... /sys/kernel/config/dlm/cluster/comms/1/addr: write failed: 17 -1

Doing a:

cat /sys/kernel/config/dlm/cluster/comms/1/addr_list

reported nothing. This was being seen on cluster with nodeid 1 and it's
local configuration. To be sure the configfs entries are in sync with
lowcomms connection structures we always call dlm_midcomms_close() to be
sure the lowcomms connection gets removed when the configfs entry gets
dropped.

Before commit 07ee38674a0b ("fs: dlm: filter ourself midcomms calls") it
was just doing this by accident and the filter by doing:

if (nodeid == dlm_our_nodeid())
	return 0;

inside dlm_midcomms_close() was never been hit because drop_comm() sets
local_comm to NULL and cause that dlm_our_nodeid() returns always the
invalid nodeid 0.

Fixes: 07ee38674a0b ("fs: dlm: filter ourself midcomms calls")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>

This patch changes the time when we sending an ack back to tell the
other side it can free some message because it is arrived on the
receiver node, due random reconnects e.g. TCP resets this is handled as
well on application layer to not let DLM run into a deadlock state.

The current handling has the following problems:

1. We end in situations that we only send an ack back message of 16
   bytes out and no other messages. Whereas DLM has logic to combine
   so much messages as it can in one send() socket call. This behaviour
   can be discovered by "trace-cmd start -e dlm_recv" and observing the
   ret field being 16 bytes.

2. When processing of DLM messages will never end because we receive a
   lot of messages, we will not send an ack back as it happens when
   the processing loop ends.

This patch introduces a likely and unlikely threshold case. The likely
case will send an ack back on a transmit path if the threshold is
triggered of amount of processed upper layer protocol. This will solve
issue 1 because it will be send when another normal DLM message will be
sent. It solves issue 2 because it is not part of the processing loop.

There is however a unlikely case, the unlikely case has a bigger
threshold and will be triggered when we only receive messages and do not
sent any message back. This case avoids that the sending node will keep
a lot of message for a long time as we send sometimes ack backs to tell
the sender to finally release messages.

The atomic cmpxchg() is there to provide a atomically ack send with
reset of the upper layer protocol delivery counter.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>

Currently seq_next is only be read on the receive side which processed
in an ordered way. The seq_send is being protected by locks. To being
able to read the seq_next value on send side as well we convert it to an
atomic_t value. The atomic_cmpxchg() is probably not necessary, however
the atomic_inc() depends on a if coniditional and this should be handled
in an atomic context.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>

Currently the lkb_wait_count is locked by the rsb lock and it should be
fine to handle lkb_wait_count as non atomic_t value. However for the
overall process of reducing locking this patch converts it to an
atomic_t value.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>

It makes no sense to call midcomms/lowcomms functionality for the local
node as socket functionality is only required for remote nodes. This
patch filters those calls in the upper layer of lockspace membership
handling instead of doing it in midcomms/lowcomms layer as they should
never be aware of local nodeid.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>