linux-stable.git/drivers, branch v5.4.85

serial: 8250_omap: Avoid FIFO corruption caused by MDR1 access

2020-12-21T12:27:06+00:00

commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream.

It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.

Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.

A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.

Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin 
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman

USB: sisusbvga: Make console support depend on BROKEN

2020-12-21T12:27:06+00:00

commit 862ee699fefe1e6d6f2c1518395f0b999b8beb15 upstream.

The console part of sisusbvga is broken vs. printk(). It uses in_atomic()
to detect contexts in which it cannot sleep despite the big fat comment in
preempt.h which says: Do not use in_atomic() in driver code.

in_atomic() does not work on kernels with CONFIG_PREEMPT_COUNT=n which
means that spin/rw_lock held regions are not detected by it.

There is no way to make this work by handing context information through to
the driver and this only can be solved once the core printk infrastructure
supports sleepable console drivers.

Make it depend on BROKEN for now.

Fixes: 1bbb4f2035d9 ("[PATCH] USB: sisusb[vga] update")
Signed-off-by: Thomas Gleixner 
Cc: Thomas Winischhofer 
Cc: Greg Kroah-Hartman 
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101109.603244207@linutronix.de
Signed-off-by: Greg Kroah-Hartman

USB: UAS: introduce a quirk to set no_write_same

2020-12-21T12:27:06+00:00

commit 8010622c86ca5bb44bc98492f5968726fc7c7a21 upstream.

UAS does not share the pessimistic assumption storage is making that
devices cannot deal with WRITE_SAME.  A few devices supported by UAS,
are reported to not deal well with WRITE_SAME. Those need a quirk.

Add it to the device that needs it.

Reported-by: David C. Partridge 
Signed-off-by: Oliver Neukum 
Cc: stable 
Link: https://lore.kernel.org/r/20201209152639.9195-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman

xhci-pci: Allow host runtime PM as default for Intel Alpine Ridge LP

2020-12-21T12:27:06+00:00

commit c4d1ca05b8e68a4b5a3c4455cb6ec25b3df6d9dd upstream.

The xHCI controller on Alpine Ridge LP keeps the whole Thunderbolt
controller awake if the host controller is not allowed to sleep.
This is the case even if no USB devices are connected to the host.

Add the Intel Alpine Ridge LP product-id to the list of product-ids
for which we allow runtime PM by default.

Fixes: 2815ef7fe4d4 ("xhci-pci: allow host runtime PM as default for Intel Alpine and Titan Ridge")
Cc: 
Reviewed-by: Mika Westerberg 
Signed-off-by: Hans de Goede 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20201208092912.1773650-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

xhci: Give USB2 ports time to enter U3 in bus suspend

2020-12-21T12:27:06+00:00

commit c1373f10479b624fb6dba0805d673e860f1b421d upstream.

If a USB2 device wakeup is not enabled/supported the link state may
still be in U0 in xhci_bus_suspend(), where it's then manually put
to suspended U3 state.

Just as with selective suspend the device needs time to enter U3
suspend before continuing with further suspend operations
(e.g. system suspend), otherwise we may enter system suspend with link
state in U0.

[commit message rewording -Mathias]

Cc: 
Signed-off-by: Li Jun 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20201208092912.1773650-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

USB: add RESET_RESUME quirk for Snapscan 1212

2020-12-21T12:27:05+00:00

commit 08a02f954b0def3ada8ed6d4b2c7bcb67e885e9c upstream.

I got reports that some models of this old scanner need
this when using runtime PM.

Signed-off-by: Oliver Neukum 
Cc: stable 
Link: https://lore.kernel.org/r/20201207130323.23857-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman

USB: dummy-hcd: Fix uninitialized array use in init()

2020-12-21T12:27:05+00:00

commit e90cfa813da7a527785033a0b247594c2de93dd8 upstream.

This error path

	err_add_pdata:
		for (i = 0; i < mod_data.num; i++)
			kfree(dum[i]);

can be triggered when not all dum's elements are initialized.

Fix this by initializing all dum's elements to NULL.

Acked-by: Alan Stern 
Cc: stable 
Signed-off-by: Bui Quang Minh 
Link: https://lore.kernel.org/r/1607063090-3426-1-git-send-email-minhquangbui99@gmail.com
Signed-off-by: Greg Kroah-Hartman

net: stmmac: delete the eee_ctrl_timer after napi disabled

2020-12-21T12:27:05+00:00

[ Upstream commit 5f58591323bf3f342920179f24515935c4b5fd60 ]

There have chance to re-enable the eee_ctrl_timer and fire the timer
in napi callback after delete the timer in .stmmac_release(), which
introduces to access eee registers in the timer function after clocks
are disabled then causes system hang. Found this issue when do
suspend/resume and reboot stress test.

It is safe to delete the timer after napi disabled and disable lpi mode.

Fixes: d765955d2ae0b ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Fugang Duan 
Signed-off-by: Joakim Zhang 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: stmmac: dwmac-meson8b: fix mask definition of the m250_sel mux

2020-12-21T12:27:05+00:00

[ Upstream commit 82ca4c922b8992013a238d65cf4e60cc33e12f36 ]

The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.

While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.

Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl 
Reviewed-by: Jerome Brunet 
Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

net: ll_temac: Fix potential NULL dereference in temac_probe()

2020-12-21T12:27:05+00:00

[ Upstream commit cc6596fc7295e9dcd78156ed42f9f8e1221f7530 ]

platform_get_resource() may fail and in this case a NULL dereference
will occur.

Fix it to use devm_platform_ioremap_resource() instead of calling
platform_get_resource() and devm_ioremap().

This is detected by Coccinelle semantic patch.

@@
expression pdev, res, n, t, e, e1, e2;
@@

res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t, n);
+ if (!res)
+   return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);

Fixes: 8425c41d1ef7 ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Zhang Changzhong 
Acked-by: Esben Haabendal 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman