linux-stable.git/drivers, branch v4.4.190

bonding: Add vlan tx offload to hw_enc_features

2019-08-25T08:53:06+00:00

[ Upstream commit d595b03de2cb0bdf9bcdf35ff27840cc3a37158f ]

As commit 30d8177e8ac7 ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.

Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:

	 if (skb->encapsulation)
                 features &= dev->hw_enc_features;

clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e8ac7 like this:

vlan_dev_hard_start_xmit
  -->dev_queue_xmit
    -->validate_xmit_skb
      -->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
      -->validate_xmit_vlan
        -->__vlan_hwaccel_push_inside //skb->tci is cleared
...
 --> bond_start_xmit
   --> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
     --> __skb_flow_dissect // nhoff point to IP header
        -->  case htons(ETH_P_8021Q)
             // skb_vlan_tag_present is false, so
             vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
             //vlan point to ip header wrongly

Fixes: b2a103e6d0af ("bonding: convert to ndo_fix_features")
Signed-off-by: YueHaibing 
Acked-by: Jay Vosburgh 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net/mlx5e: Only support tx/rx pause setting for port owner

2019-08-25T08:53:05+00:00

[ Upstream commit 466df6eb4a9e813b3cfc674363316450c57a89c5 ]

Only support changing tx/rx pause frame setting if the net device
is the vport group manager.

Fixes: 3c2d18ef22df ("net/mlx5e: Support ethtool get/set_pauseparam")
Signed-off-by: Huy Nguyen 
Reviewed-by: Parav Pandit 
Signed-off-by: Saeed Mahameed 
Signed-off-by: Greg Kroah-Hartman

xen/netback: Reset nr_frags before freeing skb

2019-08-25T08:53:05+00:00

[ Upstream commit 3a0233ddec554b886298de2428edb5c50a20e694 ]

At this point nr_frags has been incremented but the frag does not yet
have a page assigned so freeing the skb results in a crash. Reset
nr_frags before freeing the skb to prevent this.

Signed-off-by: Ross Lagerwall 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

iommu/amd: Move iommu_init_pci() to .init section

2019-08-25T08:53:05+00:00

commit 24d2c521749d8547765b555b7a85cca179bb2275 upstream.

The function is only called from another __init function, so
it should be moved to .init too.

Signed-off-by: Joerg Roedel 
Signed-off-by: Greg Kroah-Hartman

IB/mlx5: Make coding style more consistent

2019-08-25T08:53:04+00:00

commit 0025b0bdeae7c13b8ab1dce64b0108ed9c071e2e upstream.

These three related functions can't agree whether to put the
umrwr on the stack dirty and then memset it, or to initialize
it on the stack.  Make them all agree.

Signed-off-by: Doug Ledford 
Signed-off-by: Greg Kroah-Hartman

RDMA: Directly cast the sockaddr union to sockaddr

2019-08-25T08:53:04+00:00

commit 641114d2af312d39ca9bbc2369d18a5823da51c6 upstream.

gcc 9 now does allocation size tracking and thinks that passing the member
of a union and then accessing beyond that member's bounds is an overflow.

Instead of using the union member, use the entire union with a cast to
get to the sockaddr. gcc will now know that the memory extends the full
size of the union.

Signed-off-by: Jason Gunthorpe 
Signed-off-by: Greg Kroah-Hartman

scsi: fcoe: Embed fc_rport_priv in fcoe_rport structure

2019-08-25T08:53:04+00:00

commit 023358b136d490ca91735ac6490db3741af5a8bd upstream.

Gcc-9 complains for a memset across pointer boundaries, which happens as
the code tries to allocate a flexible array on the stack.  Turns out we
cannot do this without relying on gcc-isms, so with this patch we'll embed
the fc_rport_priv structure into fcoe_rport, can use the normal
'container_of' outcast, and will only have to do a memset over one
structure.

Signed-off-by: Hannes Reinecke 
Signed-off-by: Martin K. Petersen 
Signed-off-by: Greg Kroah-Hartman

Input: psmouse - fix build error of multiple definition

2019-08-25T08:53:03+00:00

commit 49e6979e7e92cf496105b5636f1df0ac17c159c0 upstream.

trackpoint_detect() should be static inline while
CONFIG_MOUSE_PS2_TRACKPOINT is not set, otherwise, we build fails:

drivers/input/mouse/alps.o: In function `trackpoint_detect':
alps.c:(.text+0x8e00): multiple definition of `trackpoint_detect'
drivers/input/mouse/psmouse-base.o:psmouse-base.c:(.text+0x1b50): first defined here

Reported-by: Hulk Robot 
Fixes: 55e3d9224b60 ("Input: psmouse - allow disabing certain protocol extensions")
Signed-off-by: YueHaibing 
Signed-off-by: Dmitry Torokhov 
Cc: Hui Wang 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: Add Motorola modem UARTs

2019-08-25T08:53:03+00:00

commit 6caf0be40a707689e8ff8824fdb96ef77685b1ba upstream.

On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams .

As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold .

The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork .

However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.

The ttyUSB ports on Droid 4 are:

ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable

The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.

To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.

The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.

The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.

The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.

Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.

I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.

After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=2a70 Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=88(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=8b(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8c(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=08(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=8d(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

In 22b8:900e "qc_dload" mode the device shows up as:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=900e Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

And in 22b8:4281 "ram_downloader" mode the device shows up as:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=4281 Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

Cc: Bjørn Mork 
Cc: Dan Williams 
Cc: Lars Melin 
Cc: Marcel Partap 
Cc: Merlijn Wajer 
Cc: Michael Scott 
Cc: NeKit 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Tested-by: Pavel Machek 
Signed-off-by: Tony Lindgren 
Cc: stable 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add the BroadMobi BM818 card

2019-08-25T08:53:02+00:00

commit e5d8badf37e6b547842f2fcde10361b29e08bd36 upstream.

Add a VID:PID for the BroadMobi BM818 M.2 card

T:  Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2020 ProdID=2060 Rev=00.00
S:  Manufacturer=Qualcomm, Incorporated
S:  Product=Qualcomm CDMA Technologies MSM
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

Signed-off-by: Bob Ham 
Signed-off-by: Angus Ainslie (Purism) 
Cc: stable 
[ johan: use USB_DEVICE_INTERFACE_CLASS() ]
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman