linux-stable.git/drivers, branch v4.4.1

team: Replace rcu_read_lock with a mutex in team_vlan_rx_kill_vid

2016-01-31T19:29:01+00:00

[ Upstream commit 60a6531bfe49555581ccd65f66a350cc5693fcde ]

We can't be within an RCU read-side critical section when deleting
VLANs, as underlying drivers might sleep during the hardware operation.
Therefore, replace the RCU critical section with a mutex. This is
consistent with team_vlan_rx_add_vid.

Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Acked-by: Jiri Pirko 
Signed-off-by: Ido Schimmel 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net/mlx5_core: Fix trimming down IRQ number

2016-01-31T19:29:01+00:00

[ Upstream commit 0b6e26ce89391327d955a756a7823272238eb867 ]

With several ConnectX-4 cards installed on a server, one may receive
irqn > 255 from the kernel API, which we mistakenly trim to 8bit.

This causes EQ creation failure with the following stack trace:
[] dump_stack+0x48/0x64
[] __setup_irq+0x3a1/0x4f0
[] request_threaded_irq+0x120/0x180
[] ? mlx5_eq_int+0x450/0x450 [mlx5_core]
[] mlx5_create_map_eq+0x1e4/0x2b0 [mlx5_core]
[] alloc_comp_eqs+0xb1/0x180 [mlx5_core]
[] mlx5_dev_init+0x5e9/0x6e0 [mlx5_core]
[] init_one+0x99/0x1c0 [mlx5_core]
[] local_pci_probe+0x4c/0xa0

Fixing it by changing of the irqn type from u8 to unsigned int to
support values > 255

Fixes: 61d0e73e0a5a ('net/mlx5_core: Use the the real irqn in eq->irqn')
Reported-by: Jiri Pirko 
Signed-off-by: Doron Tsur 
Signed-off-by: Matan Barak 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

dwc_eth_qos: Fix dma address for multi-fragment skbs

2016-01-31T19:29:00+00:00

[ Upstream commit d461873272169a3fc3a8d155d7b1c92e9d97b419 ]

The offset inside the fragment was not used for the dma address and
silent data corruption resulted because TSO makes the checksum match.

Fixes: 077742dac2c7 ("dwc_eth_qos: Add support for Synopsys DWC Ethernet QoS")
Signed-off-by: Lars Persson 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

bonding: Prevent IPv6 link local address on enslaved devices

2016-01-31T19:29:00+00:00

[ Upstream commit 03d84a5f83a67e692af00a3d3901e7820e3e84d5 ]

Commit 1f718f0f4f97 ("bonding: populate neighbour's private on enslave")
undoes the fix provided by commit c2edacf80e15 ("bonding / ipv6: no addrconf
for slaves separately from master") by effectively setting the slave flag
after the slave has been opened.  If the slave comes up quickly enough, it
will go through the IPv6 addrconf before the slave flag has been set and
will get a link local IPv6 address.

In order to ensure that addrconf knows to ignore the slave devices on state
change, set IFF_SLAVE before dev_open() during bonding enslavement.

Fixes: 1f718f0f4f97 ("bonding: populate neighbour's private on enslave")
Signed-off-by: Karl Heiss 
Signed-off-by: Jay Vosburgh 
Reviewed-by: Jarod Wilson 
Signed-off-by: Andy Gospodarek 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

vxlan: fix test which detect duplicate vxlan iface

2016-01-31T19:28:59+00:00

[ Upstream commit 07b9b37c227cb8d88d478b4a9c5634fee514ede1 ]

When a vxlan interface is created, the driver checks that there is not
another vxlan interface with the same properties. To do this, it checks
the existing vxlan udp socket. Since commit 1c51a9159dde, the creation of
the vxlan socket is done only when the interface is set up, thus it breaks
that test.

Example:
$ ip l a vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip l a vxlan11 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip -br l | grep vxlan
vxlan10          DOWN           f2:55:1c:6a:fb:00 
vxlan11          DOWN           7a:cb:b9:38:59:0d 

Instead of checking sockets, let's loop over the vxlan iface list.

Fixes: 1c51a9159dde ("vxlan: fix race caused by dropping rtnl_unlock")
Reported-by: Thomas Faivre 
Signed-off-by: Nicolas Dichtel 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

xhci: refuse loading if nousb is used

2016-01-31T19:28:59+00:00

commit 1eaf35e4dd592c59041bc1ed3248c46326da1f5f upstream.

The module should fail to load.

Signed-off-by: Oliver Neukum 
Signed-off-by: Greg Kroah-Hartman

usb: core: lpm: fix usb3_hardware_lpm sysfs node

2016-01-31T19:28:58+00:00

commit bf5ce5bf3cc7136fd7fe5e8999a580bc93a9c8f6 upstream.

Commit 655fe4effe0f ("usbcore: add sysfs support to xHCI usb3
hardware LPM") introduced usb3_hardware_lpm sysfs node. This
doesn't show the correct status of USB3 U1 and U2 LPM status.

This patch fixes this by replacing usb3_hardware_lpm with two
nodes, usb3_hardware_lpm_u1 (for U1) and usb3_hardware_lpm_u2
(for U2), and recording the U1/U2 LPM status in right places.

This patch should be back-ported to kernels as old as 4.3,
that contains Commit 655fe4effe0f ("usbcore: add sysfs support
to xHCI usb3 hardware LPM").

Signed-off-by: Lu Baolu 
Signed-off-by: Greg Kroah-Hartman

USB: cp210x: add ID for ELV Marble Sound Board 1

2016-01-31T19:28:58+00:00

commit f7d7f59ab124748156ea551edf789994f05da342 upstream.

Add the USB device ID for ELV Marble Sound Board 1.

Signed-off-by: Oliver Freyermuth 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

rtlwifi: fix memory leak for USB device

2016-01-31T19:28:58+00:00

commit 17bc55864f81dd730d05f09b1641312a7990d636 upstream.

Free skb for received frames with a wrong checksum. This can happen
pretty rapidly, exhausting all memory.

This fixes a memleak (detected with kmemleak). Originally found while
using monitor mode, but it also appears during managed mode (once the
link is up).

Signed-off-by: Peter Wu 
ACKed-by: Larry Finger 
Signed-off-by: Kalle Valo 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

2016-01-09T22:53:48+00:00

Pull SCSI fix from James Bottomley:
 "A single fix for machines with pages > 4k (PPC mostly).

  There's a bug in our optimal transfer size code where we don't account
  for pages > 4k and can set the transfer size to be less than the page
  size causing nasty failures"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  sd: Reject optimal transfer length smaller than page size