linux-stable.git/drivers, branch v3.4.107 Linux kernel stable tree PCI: Handle read-only BARs on AMD CS553x devices 2015-04-14T09:34:04+00:00 Myron Stowe myron.stowe@redhat.com 2015-02-03T23:01:24+00:00 d4e393820d2ed20fc6a4088f3eda44458764d997 commit 06cf35f903aa6da0cc8d9f81e9bcd1f7e1b534bb upstream. Some AMD CS553x devices have read-only BARs because of a firmware or hardware defect. There's a workaround in quirk_cs5536_vsa(), but it no longer works after 36e8164882ca ("PCI: Restore detection of read-only BARs"). Prior to 36e8164882ca, we filled in res->start; afterwards we leave it zeroed out. The quirk only updated the size, so the driver tried to use a region starting at zero, which didn't work. Expand quirk_cs5536_vsa() to read the base addresses from the BARs and hard-code the sizes. On Nix's system BAR 2's read-only value is 0x6200. Prior to 36e8164882ca, we interpret that as a 512-byte BAR based on the lowest-order bit set. Per datasheet sec 5.6.1, that BAR (MFGPT) requires only 64 bytes; use that to avoid clearing any address bits if a platform uses only 64-byte alignment. [bhelgaas: changelog, reduce BAR 2 size to 64] Fixes: 36e8164882ca ("PCI: Restore detection of read-only BARs") Link: https://bugzilla.kernel.org/show_bug.cgi?id=85991#c4 Link: http://support.amd.com/TechDocs/31506_cs5535_databook.pdf Link: http://support.amd.com/TechDocs/33238G_cs5536_db.pdf Reported-and-tested-by: Nix <nix@esperi.org.uk> Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit 06cf35f903aa6da0cc8d9f81e9bcd1f7e1b534bb upstream.

Some AMD CS553x devices have read-only BARs because of a firmware or
hardware defect.  There's a workaround in quirk_cs5536_vsa(), but it no
longer works after 36e8164882ca ("PCI: Restore detection of read-only
BARs").  Prior to 36e8164882ca, we filled in res->start; afterwards we
leave it zeroed out.  The quirk only updated the size, so the driver tried
to use a region starting at zero, which didn't work.

Expand quirk_cs5536_vsa() to read the base addresses from the BARs and
hard-code the sizes.

On Nix's system BAR 2's read-only value is 0x6200.  Prior to 36e8164882ca,
we interpret that as a 512-byte BAR based on the lowest-order bit set.  Per
datasheet sec 5.6.1, that BAR (MFGPT) requires only 64 bytes; use that to
avoid clearing any address bits if a platform uses only 64-byte alignment.

[bhelgaas: changelog, reduce BAR 2 size to 64]
Fixes: 36e8164882ca ("PCI: Restore detection of read-only BARs")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85991#c4
Link: http://support.amd.com/TechDocs/31506_cs5535_databook.pdf
Link: http://support.amd.com/TechDocs/33238G_cs5536_db.pdf
Reported-and-tested-by: Nix <nix@esperi.org.uk>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
spi: dw: revisit FIFO size detection again 2015-04-14T09:34:04+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2015-02-25T09:39:36+00:00 8b19cfea81e37f215399a3d5481f899ba24f30c5 commit 9d239d353c319f9ff884c287ce47feb7cdf60ddc upstream. The commit d297933cc7fc (spi: dw: Fix detecting FIFO depth) tries to fix the logic of the FIFO detection based on the description on the comments. However, there is a slight difference between numbers in TX Level and TX FIFO size. So, by specification the FIFO size would be in a range 2-256 bytes. From TX Level prospective it means we can set threshold in the range 0-(FIFO size - 1) bytes. Hence there are currently two issues: a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be either 0 or 1 byte; b) FIFO size is incorrectly decreased by 1 which already done by meaning of TX Level register. This patch fixes it eventually right. Fixes: d297933cc7fc (spi: dw: Fix detecting FIFO depth) Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit 9d239d353c319f9ff884c287ce47feb7cdf60ddc upstream.

The commit d297933cc7fc (spi: dw: Fix detecting FIFO depth) tries to fix the
logic of the FIFO detection based on the description on the comments. However,
there is a slight difference between numbers in TX Level and TX FIFO size.

So, by specification the FIFO size would be in a range 2-256 bytes. From TX
Level prospective it means we can set threshold in the range 0-(FIFO size - 1)
bytes. Hence there are currently two issues:
  a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
     either 0 or 1 byte;
  b) FIFO size is incorrectly decreased by 1 which already done by meaning of
     TX Level register.

This patch fixes it eventually right.

Fixes: d297933cc7fc (spi: dw: Fix detecting FIFO depth)
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
s390/3215: fix tty output containing tabs 2015-04-14T09:34:03+00:00 Martin Schwidefsky schwidefsky@de.ibm.com 2014-08-13T10:01:30+00:00 9493ef4e311954d800e494196dccc423e5f1cfa5 commit e512d56c799517f33b301d81e9a5e0ebf30c2d1e upstream. git commit 37f81fa1f63ad38e16125526bb2769ae0ea8d332 "n_tty: do O_ONLCR translation as a single write" surfaced a bug in the 3215 device driver. In combination this broke tab expansion for tty ouput. The cause is an asymmetry in the behaviour of tty3215_ops->write vs tty3215_ops->put_char. The put_char function scans for '\t' but the write function does not. As the driver has logic for the '\t' expansion remove XTABS from c_oflag of the initial termios as well. Reported-by: Stephen Powell <zlinuxman@wowway.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit e512d56c799517f33b301d81e9a5e0ebf30c2d1e upstream.

git commit 37f81fa1f63ad38e16125526bb2769ae0ea8d332
"n_tty: do O_ONLCR translation as a single write"
surfaced a bug in the 3215 device driver. In combination this
broke tab expansion for tty ouput.

The cause is an asymmetry in the behaviour of tty3215_ops->write
vs tty3215_ops->put_char. The put_char function scans for '\t'
but the write function does not.

As the driver has logic for the '\t' expansion remove XTABS
from c_oflag of the initial termios as well.

Reported-by: Stephen Powell <zlinuxman@wowway.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Bluetooth: ath3k: workaround the compatibility issue with xHCI controller 2015-04-14T09:34:03+00:00 Adam Lee adam.lee@canonical.com 2015-01-28T20:30:27+00:00 c12b6db9f1a9841949ce5776b71dffb03f911692 commit c561a5753dd631920c4459a067d22679b3d110d6 upstream. BugLink: https://bugs.launchpad.net/bugs/1400215 ath3k devices fail to load firmwares on xHCI buses, but work well on EHCI, this might be a compatibility issue between xHCI and ath3k chips. As my testing result, those chips will work on xHCI buses again with this patch. This workaround is from Qualcomm, they also did some workarounds in Windows driver. Signed-off-by: Adam Lee <adam.lee@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit c561a5753dd631920c4459a067d22679b3d110d6 upstream.

BugLink: https://bugs.launchpad.net/bugs/1400215

ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.

This workaround is from Qualcomm, they also did some workarounds in
Windows driver.

Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
staging: comedi: cb_pcidas64: fix incorrect AI range code handling 2015-04-14T09:34:03+00:00 Ian Abbott abbotti@mev.co.uk 2015-01-19T14:47:27+00:00 3d05f9f37cb5e1722163275b8c6284fe5570c55e commit be8e89087ec2d2c8a1ad1e3db64bf4efdfc3c298 upstream. The hardware range code values and list of valid ranges for the AI subdevice is incorrect for several supported boards. The hardware range code values for all boards except PCI-DAS4020/12 is determined by calling `ai_range_bits_6xxx()` based on the maximum voltage of the range and whether it is bipolar or unipolar, however it only returns the correct hardware range code for the PCI-DAS60xx boards. For PCI-DAS6402/16 (and /12) it returns the wrong code for the unipolar ranges. For PCI-DAS64/Mx/16 it returns the wrong code for all the ranges and the comedi range table is incorrect. Change `ai_range_bits_6xxx()` to use a look-up table pointed to by new member `ai_range_codes` of `struct pcidas64_board` to map the comedi range table indices to the hardware range codes. Use a new comedi range table for the PCI-DAS64/Mx/16 boards (and the commented out variants). Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [Ian: Backported to 3.4] Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit be8e89087ec2d2c8a1ad1e3db64bf4efdfc3c298 upstream.

The hardware range code values and list of valid ranges for the AI
subdevice is incorrect for several supported boards.  The hardware range
code values for all boards except PCI-DAS4020/12 is determined by
calling `ai_range_bits_6xxx()` based on the maximum voltage of the range
and whether it is bipolar or unipolar, however it only returns the
correct hardware range code for the PCI-DAS60xx boards.  For
PCI-DAS6402/16 (and /12) it returns the wrong code for the unipolar
ranges.  For PCI-DAS64/Mx/16 it returns the wrong code for all the
ranges and the comedi range table is incorrect.

Change `ai_range_bits_6xxx()` to use a look-up table pointed to by new
member `ai_range_codes` of `struct pcidas64_board` to map the comedi
range table indices to the hardware range codes.  Use a new comedi range
table for the PCI-DAS64/Mx/16 boards (and the commented out variants).

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Ian: Backported to 3.4]
Signed-off-by: Zefan Li <lizefan@huawei.com>
Bluetooth: Add USB device 04ca:3010 as Atheros AR3012 2015-04-14T09:34:02+00:00 Janne Heikkinen janne.m.heikkinen@gmail.com 2014-12-09T05:44:51+00:00 3022d3dd56f905d34054a62f569c16d5749e1e85 commit 134d3b3550f050b9bec37111824452064d1ed928 upstream. Asus X553MA has USB device 04ca:3010 that is Atheros AR3012 or compatible. Device from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 27 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3010 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Janne Heikkinen <janne.m.heikkinen@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit 134d3b3550f050b9bec37111824452064d1ed928 upstream.

Asus X553MA has USB device 04ca:3010 that is Atheros AR3012
or compatible.

Device from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 27 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3010 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Janne Heikkinen <janne.m.heikkinen@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
Bluetooth: ath3k: Add support of MCI 13d3:3408 bt device 2015-04-14T09:34:02+00:00 Dmitry Tunin hanipouspilot@gmail.com 2014-11-25T17:19:52+00:00 7461373f3b62900502b56254244fe6b49ecdc936 commit 3bb30a7cdf9242aca90d49aa41baebf9458f96f0 upstream. Add support for Bluetooth MCI WB335 (AR9565) Wi-Fi+bt module. This Bluetooth module requires loading patch and sysconfig by ath3k driver. T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 20 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3408 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit 3bb30a7cdf9242aca90d49aa41baebf9458f96f0 upstream.

Add support for Bluetooth MCI WB335 (AR9565) Wi-Fi+bt module. This
Bluetooth module requires loading patch and sysconfig by ath3k driver.

T:  Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 20 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3408 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Bluetooth: Add support for Acer [0489:e078] 2015-04-14T09:34:01+00:00 Anantha Krishnan ananthk@codeaurora.org 2014-10-06T11:01:49+00:00 94a30505c3defd78eb13e94d9a7d69a3c2e092bc commit 4b552bc9edfdc947862af225a0e2521edb5d37a0 upstream. Add support for the QCA6174 chip. T: Bus=06 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e078 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Anantha Krishnan <ananthk@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: Joseph Salisbury <joseph.salisbury@canonical.com> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit 4b552bc9edfdc947862af225a0e2521edb5d37a0 upstream.

Add support for the QCA6174 chip.

    T:  Bus=06 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
    D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
    P:  Vendor=0489 ProdID=e078 Rev=00.01
    C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
    I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Anantha Krishnan <ananthk@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Joseph Salisbury <joseph.salisbury@canonical.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
Add a new PID/VID 0227/0930 for AR3012. 2015-04-14T09:34:01+00:00 Vincent Zwanenburg vincentz@topmail.ie 2014-08-08T11:33:56+00:00 a756fa648c16bad2539fd8eac76665568cba4942 commit 89d2975fa06e66ea0d3665d91f799fb1ce4b8bad upstream. usb devices info: T: Bus=01 Lev=02 Prnt=05 Port=00 Cnt=01 Dev#= 20 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0227 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Vincent Zwanenburg <vincentz@topmail.ie> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit 89d2975fa06e66ea0d3665d91f799fb1ce4b8bad upstream.

usb devices info:

T:  Bus=01 Lev=02 Prnt=05 Port=00 Cnt=01 Dev#= 20 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=0227 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Vincent Zwanenburg <vincentz@topmail.ie>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
Bluetooth: Add support for Broadcom device of Asus Z97-DELUXE motherboard 2015-04-14T09:34:01+00:00 Marcel Holtmann marcel@holtmann.org 2014-07-21T12:02:33+00:00 c96bfe4a45742b79a2e076f1a10ae2becda8914f commit c2aef6e8cbebd60f79555baeb9266e220f135a44 upstream. The Asus Z97-DELUXE motherboard contains a Broadcom based Bluetooth controller on the USB bus. However vendor and product ID are listed as ASUSTek Computer. T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0b05 ProdID=17cf Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=54271E910064 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Reported-by: Jerome Leclanche <jerome@leclan.ch> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com> 
commit c2aef6e8cbebd60f79555baeb9266e220f135a44 upstream.

The Asus Z97-DELUXE motherboard contains a Broadcom based Bluetooth
controller on the USB bus. However vendor and product ID are listed
as ASUSTek Computer.

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17cf Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=54271E910064
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Reported-by: Jerome Leclanche <jerome@leclan.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>