linux-stable.git/drivers, branch v3.4.100

iommu/vt-d: Disable translation if already enabled

2014-07-28T14:06:46+00:00

commit 3a93c841c2b3b14824f7728dd74bd00a1cedb806 upstream.

This patch disables translation(dma-remapping) before its initialization
if it is already enabled.

This is needed for kexec/kdump boot. If dma-remapping is enabled in the
first kernel, it need to be disabled before initializing its page table
during second kernel boot. Wei Hu also reported that this is needed
when second kernel boots with intel_iommu=off.

Basically iommu->gcmd is used to know whether translation is enabled or
disabled, but it is always zero at boot time even when translation is
enabled since iommu->gcmd is initialized without considering such a
case. Therefor this patch synchronizes iommu->gcmd value with global
command register when iommu structure is allocated.

Signed-off-by: Takao Indoh 
Signed-off-by: Joerg Roedel 
[wyj: Backported to 3.4: adjust context]
Signed-off-by: Yijing Wang 
Signed-off-by: Greg Kroah-Hartman

drm/radeon: avoid leaking edid data

2014-07-28T14:06:46+00:00

commit 0ac66effe7fcdee55bda6d5d10d3372c95a41920 upstream.

In some cases we fetch the edid in the detect() callback
in order to determine what sort of monitor is connected.
If that happens, don't fetch the edid again in the get_modes()
callback or we will leak the edid.

Signed-off-by: Alex Deucher 
Signed-off-by: Greg Kroah-Hartman

mwifiex: fix Tx timeout issue

2014-07-28T14:06:46+00:00

commit d76744a93246eccdca1106037e8ee29debf48277 upstream.

https://bugzilla.kernel.org/show_bug.cgi?id=70191
https://bugzilla.kernel.org/show_bug.cgi?id=77581

It is observed that sometimes Tx packet is downloaded without
adding driver's txpd header. This results in firmware parsing
garbage data as packet length. Sometimes firmware is unable
to read the packet if length comes out as invalid. This stops
further traffic and timeout occurs.

The root cause is uninitialized fields in tx_info(skb->cb) of
packet used to get garbage values. In this case if
MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd
header was skipped. This patch makes sure that tx_info is
correctly initialized to fix the problem.

Reported-by: Andrew Wiley 
Reported-by: Linus Gasser 
Reported-by: Michael Hirsch 
Tested-by: Xinming Hu 
Signed-off-by: Amitkumar Karwar 
Signed-off-by: Maithili Hinge 
Signed-off-by: Avinash Patil 
Signed-off-by: Bing Zhao 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

sunvnet: clean up objects created in vnet_new() on vnet_exit()

2014-07-28T14:06:45+00:00

[ Upstream commit a4b70a07ed12a71131cab7adce2ce91c71b37060 ]

Nothing cleans up the objects created by
vnet_new(), they are completely leaked.

vnet_exit(), after doing the vio_unregister_driver() to clean
up ports, should call a helper function that iterates over vnet_list
and cleans up those objects. This includes unregister_netdevice()
as well as free_netdev().

Signed-off-by: Sowmini Varadhan 
Acked-by: Dave Kleikamp 
Reviewed-by: Karl Volz 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: pppoe: use correct channel MTU when using Multilink PPP

2014-07-28T14:06:45+00:00

[ Upstream commit a8a3e41c67d24eb12f9ab9680cbb85e24fcd9711 ]

The PPP channel MTU is used with Multilink PPP when ppp_mp_explode() (see
ppp_generic module) tries to determine how big a fragment might be. According
to RFC 1661, the MTU excludes the 2-byte PPP protocol field, see the
corresponding comment and code in ppp_mp_explode():

		/*
		 * hdrlen includes the 2-byte PPP protocol field, but the
		 * MTU counts only the payload excluding the protocol field.
		 * (RFC1661 Section 2)
		 */
		mtu = pch->chan->mtu - (hdrlen - 2);

However, the pppoe module *does* include the PPP protocol field in the channel
MTU, which is wrong as it causes the PPP payload to be 1-2 bytes too big under
certain circumstances (one byte if PPP protocol compression is used, two
otherwise), causing the generated Ethernet packets to be dropped. So the pppoe
module has to subtract two bytes from the channel MTU. This error only
manifests itself when using Multilink PPP, as otherwise the channel MTU is not
used anywhere.

In the following, I will describe how to reproduce this bug. We configure two
pppd instances for multilink PPP over two PPPoE links, say eth2 and eth3, with
a MTU of 1492 bytes for each link and a MRRU of 2976 bytes. (This MRRU is
computed by adding the two link MTUs and subtracting the MP header twice, which
is 4 bytes long.) The necessary pppd statements on both sides are "multilink
mtu 1492 mru 1492 mrru 2976". On the client side, we additionally need "plugin
rp-pppoe.so eth2" and "plugin rp-pppoe.so eth3", respectively; on the server
side, we additionally need to start two pppoe-server instances to be able to
establish two PPPoE sessions, one over eth2 and one over eth3. We set the MTU
of the PPP network interface to the MRRU (2976) on both sides of the connection
in order to make use of the higher bandwidth. (If we didn't do that, IP
fragmentation would kick in, which we want to avoid.)

Now we send a ICMPv4 echo request with a payload of 2948 bytes from client to
server over the PPP link. This results in the following network packet:

   2948 (echo payload)
 +    8 (ICMPv4 header)
 +   20 (IPv4 header)
---------------------
   2976 (PPP payload)

These 2976 bytes do not exceed the MTU of the PPP network interface, so the
IP packet is not fragmented. Now the multilink PPP code in ppp_mp_explode()
prepends one protocol byte (0x21 for IPv4), making the packet one byte bigger
than the negotiated MRRU. So this packet would have to be divided in three
fragments. But this does not happen as each link MTU is assumed to be two bytes
larger. So this packet is diveded into two fragments only, one of size 1489 and
one of size 1488. Now we have for that bigger fragment:

   1489 (PPP payload)
 +    4 (MP header)
 +    2 (PPP protocol field for the MP payload (0x3d))
 +    6 (PPPoE header)
--------------------------
   1501 (Ethernet payload)

This packet exceeds the link MTU and is discarded.

If one configures the link MTU on the client side to 1501, one can see the
discarded Ethernet frames with tcpdump running on the client. A

ping -s 2948 -c 1 192.168.15.254

leads to the smaller fragment that is correctly received on the server side:

(tcpdump -vvvne -i eth3 pppoes and ppp proto 0x3d)
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x3] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [end], length 1492

and to the bigger fragment that is not received on the server side:

(tcpdump -vvvne -i eth2 pppoes and ppp proto 0x3d)
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
  length 1515: PPPoE  [ses 0x5] MLPPP (0x003d), length 1495: seq 0x000,
  Flags [begin], length 1493

With the patch below, we correctly obtain three fragments:

52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [begin], length 1492
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [none], length 1492
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 27: PPPoE  [ses 0x1] MLPPP (0x003d), length 7: seq 0x000,
  Flags [end], length 5

And the ICMPv4 echo request is successfully received at the server side:

IP (tos 0x0, ttl 64, id 21925, offset 0, flags [DF], proto ICMP (1),
  length 2976)
    192.168.222.2 > 192.168.15.254: ICMP echo request, id 30530, seq 0,
      length 2956

The bug was introduced in commit c9aa6895371b2a257401f59d3393c9f7ac5a8698
("[PPPOE]: Advertise PPPoE MTU") from the very beginning. This patch applies
to 3.10 upwards but the fix can be applied (with minor modifications) to
kernels as old as 2.6.32.

Signed-off-by: Christoph Schulz 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

be2net: set EQ DB clear-intr bit in be_open()

2014-07-28T14:06:45+00:00

[ Upstream commit 4cad9f3b61c7268fa89ab8096e23202300399b5d ]

On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().

Signed-off-by: Suresh Reddy 
Signed-off-by: Sathya Perla 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

ACPI / battery: Retry to get battery information if failed during probing

2014-07-17T22:39:50+00:00

commit 75646e758a0ecbed5024454507d5be5b9ea9dcbf upstream.

Some machines (eg. Lenovo Z480) ECs are not stable during boot up
and causes battery driver fails to be loaded due to failure of getting
battery information from EC sometimes. After several retries, the
operation will work. This patch is to retry to get battery information 5
times if the first try fails.

[ backport to 3.14.5: removed second parameter in acpi_battery_update(),
introduced by the commit 9e50bc14a7f58b5d8a55973b2d69355852ae2dae (ACPI /
battery: Accelerate battery resume callback)]

[naszar : backport to 3.14.5]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75581
Reported-and-tested-by: naszar 
Cc: All applicable 
Signed-off-by: Lan Tianyu 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

drm/radeon: stop poisoning the GART TLB

2014-07-17T22:39:50+00:00

commit 0986c1a55ca64b44ee126a2f719a6e9f28cbe0ed upstream.

When we set the valid bit on invalid GART entries they are
loaded into the TLB when an adjacent entry is loaded. This
poisons the TLB with invalid entries which are sometimes
not correctly removed on TLB flush.

For stable inclusion the patch probably needs to be modified a bit.

Signed-off-by: Christian König 
Signed-off-by: Alex Deucher 
Signed-off-by: Greg Kroah-Hartman

hwmon: (adm1029) Ensure the fan_div cache is updated in set_fan_div

2014-07-17T22:39:50+00:00

commit 1035a9e3e9c76b64a860a774f5b867d28d34acc2 upstream.

Writing to fanX_div does not clear the cache. As a result, reading
from fanX_div may return the old value for up to two seconds
after writing a new value.

This patch ensures the fan_div cache is updated in set_fan_div().

Reported-by: Guenter Roeck 
Signed-off-by: Axel Lin 
Signed-off-by: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

hwmon: (amc6821) Fix permissions for temp2_input

2014-07-17T22:39:50+00:00

commit df86754b746e9a0ff6f863f690b1c01d408e3cdc upstream.

temp2_input should not be writable, fix it.

Reported-by: Guenter Roeck 
Signed-off-by: Axel Lin 
Signed-off-by: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman