linux-stable.git/drivers, branch v3.18.25

broadcom: fix PHY_ID_BCM5481 entry in the id table

2015-12-14T17:19:26+00:00

[ Upstream commit 3c25a860d17b7378822f35d8c9141db9507e3beb ]

Commit fcb26ec5b18d ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.

Fixes: fcb26ec5b18d ("broadcom: move all PHY_ID's to header")
Signed-off-by: Aaro Koskinen 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: qmi_wwan: add XS Stick W100-2 from 4G Systems

2015-12-14T17:19:24+00:00

[ Upstream commit 68242a5a1e2edce39b069385cbafb82304eac0f1 ]

Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9b01 Rev=02.32
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Now all important things are there:

wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)

There is also ttyUSB0, but it is not usable, at least not for at.

The device works well with qmi and ModemManager-NetworkManager.
"

Reported-by: Thomas Schäfer 
Signed-off-by: Bjørn Mork 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

sfc: push partner queue for skb->xmit_more

2015-12-14T17:17:29+00:00

[ Upstream commit b2663a4f30e85ec606b806f5135413e6d5c78d1e ]

When the IP stack passes SKBs the sfc driver puts them in 2 different TX
queues (called partners), one for checksummed and one for not checksummed.
If the SKB has xmit_more set the driver will delay pushing the work to the
NIC.

When later it does decide to push the buffers this patch ensures it also
pushes the partner queue, if that also has any delayed work. Before this
fix the work in the partner queue would be left for a long time and cause
a netdev watchdog.

Fixes: 70b33fb ("sfc: add support for skb->xmit_more")
Reported-by: Jianlin Shi 
Signed-off-by: Martin Habets 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

qmi_wwan: add Sierra Wireless MC74xx/EM74xx

2015-12-03T15:18:18+00:00

[ Upstream commit 0db65fcfcded76fe4f74e3ca9f4e2baf67b683ef ]

New device IDs shamelessly lifted from the vendor driver.

Signed-off-by: Bjørn Mork 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

virtio-net: drop NETIF_F_FRAGLIST

2015-12-03T15:17:47+00:00

[ Upstream commit 48900cb6af4282fa0fb6ff4d72a81aa3dadb5c39 ]

virtio declares support for NETIF_F_FRAGLIST, but assumes
that there are at most MAX_SKB_FRAGS + 2 fragments which isn't
always true with a fraglist.

A longer fraglist in the skb will make the call to skb_to_sgvec overflow
the sg array, leading to memory corruption.

Drop NETIF_F_FRAGLIST so we only get what we can handle.

Cc: Michael S. Tsirkin 
Signed-off-by: Jason Wang 
Acked-by: Michael S. Tsirkin 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

qmi_wwan: fix entry for HP lt4112 LTE/HSPA+ Gobi 4G Module

2015-12-03T15:12:28+00:00

[ Upstream commit 70910791731b5956171e1bfcad707766b8e18fee ]

The lt4112 is a HP branded Huawei me906e modem. Like other Huawei
modems, it does not have a fixed interface to function mapping.
Instead it uses a Huawei specific scheme: functions are mapped by
subclass and protocol.

However, the HP vendor ID is used for modems from many different
manufacturers using different schemes, so we cannot apply a generic
vendor rule like we do for the Huawei vendor ID.

Replace the previous lt4112 entry pointing to an arbitrary interface
number with a device specific subclass + protocol match.

Reported-and-tested-by: Muri Nicanor 
Tested-by: Martin Hauke 
Fixes: bb2bdeb83fb1 ("qmi_wwan: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

stmmac: Correctly report PTP capabilities.

2015-12-03T15:12:07+00:00

[ Upstream commit e6dbe1eb2db0d7a14991c06278dd3030c45fb825 ]

priv->hwts_*_en indicate if timestamping is enabled/disabled at run
time. But  priv->dma_cap.time_stamp  and priv->dma_cap.atime_stamp
indicates HW is support for PTPv1/PTPv2.

Signed-off-by: Phil Reid 
Acked-by: Richard Cochran 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net/mlx4: Copy/set only sizeof struct mlx4_eqe bytes

2015-12-03T15:11:53+00:00

[ Upstream commit c02b05011fadf8e409e41910217ca689f2fc9d91 ]

When doing memcpy/memset of EQEs, we should use sizeof struct
mlx4_eqe as the base size and not caps.eqe_size which could be bigger.

If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt
data in the master context.

When using a 64 byte stride, the memcpy copied over 63 bytes to the
slave_eq structure.  This resulted in copying over the entire eqe of
interest, including its ownership bit -- and also 31 bytes of garbage
into the next WQE in the slave EQ -- which did NOT include the ownership
bit (and therefore had no impact).

However, once the stride is increased to 128, we are overwriting the
ownership bits of *three* eqes in the slave_eq struct.  This results
in an incorrect ownership bit for those eqes, which causes the eq to
seem to be full. The issue therefore surfaced only once 128-byte EQEs
started being used in SRIOV and (overarchitectures that have 128/256
byte cache-lines such as PPC) - e.g after commit 77507aa249ae
"net/mlx4_core: Enable CQE/EQE stride support".

Fixes: 08ff32352d6f ('mlx4: 64-byte CQE/EQE support')
Signed-off-by: Carol L Soto 
Signed-off-by: Jack Morgenstein 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

ppp: fix pppoe_dev deletion condition in pppoe_release()

2015-12-03T15:11:30+00:00

[ Upstream commit 1acea4f6ce1b1c0941438aca75dd2e5c6b09db60 ]

We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev.
PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is
NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies
(po->pppoe_dev != NULL).
Since we're releasing a PPPoE socket, we want to release the pppoe_dev
if it exists and reset sk_state to PPPOX_DEAD, no matter the previous
value of sk_state. So we can just check for po->pppoe_dev and avoid any
assumption on sk->sk_state.

Fixes: 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release")
Signed-off-by: Guillaume Nault 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

macvtap: unbreak receiving of gro skb with frag list

2015-12-03T15:11:17+00:00

[ Upstream commit f23d538bc24a83c16127c2eb82c9cf1adc2b5149 ]

We don't have fraglist support in TAP_FEATURES. This will lead
software segmentation of gro skb with frag list. Fixes by having
frag list support in TAP_FEATURES.

With this patch single session of netperf receiving were restored from
about 5Gb/s to about 12Gb/s on mlx4.

Fixes a567dd6252 ("macvtap: simplify usage of tap_features")
Cc: Vlad Yasevich 
Cc: Michael S. Tsirkin 
Signed-off-by: Jason Wang 
Signed-off-by: David S. Miller 

Signed-off-by: Sasha Levin