linux-stable.git/drivers, branch v3.14.39

IB/mlx4: Saturate RoCE port PMA counters in case of overflow

2015-04-19T08:11:09+00:00

commit 61a3855bb726cbb062ef02a31a832dea455456e0 upstream.

For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.

Fixes: c37791349cc7 ('IB/mlx4: Support PMA counters for IBoE')
Signed-off-by: Majd Dibbiny 
Signed-off-by: Eran Ben Elisha 
Signed-off-by: Hadar Hen Zion 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

media: s5p-mfc: fix mmap support for 64bit arch

2015-04-19T08:11:09+00:00

commit 05b676ab42f624425d5f6519276e506b812fa058 upstream.

TASK_SIZE is depends on the systems architecture (32 or 64 bits) and it
should not be used for defining offset boundary for mmaping buffers for
CAPTURE and OUTPUT queues. This patch fixes support for MMAP calls on
the CAPTURE queue on 64bit architectures (like ARM64).

Signed-off-by: Marek Szyprowski 
Signed-off-by: Kamil Debski 
Signed-off-by: Mauro Carvalho Chehab 
Signed-off-by: Greg Kroah-Hartman

sh_veu: v4l2_dev wasn't set

2015-04-19T08:11:09+00:00

commit ab3120300be067a2d41a027c41db0b2c662ab200 upstream.

The v4l2_dev field of struct video_device must be set correctly.
This was never done for this driver, so no video nodes were created
anymore.

Signed-off-by: Hans Verkuil 
Signed-off-by: Mauro Carvalho Chehab 
Signed-off-by: Greg Kroah-Hartman

iscsi target: fix oops when adding reject pdu

2015-04-19T08:11:09+00:00

commit b815fc12d4dd2b5586184fb4f867caff05a810d4 upstream.

This fixes a oops due to a double list add when adding a reject PDU for
iscsit_allocate_iovecs allocation failures. The cmd has already been
added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call
iscsit_reject_cmd.

Note that for ERL0 the reject PDU is not actually sent, so this patch
is not completely tested. Just verified we do not oops. The problem is the
add reject functions return -1 which is returned all the way up to
iscsi_target_rx_thread which for ERL0 will drop the connection.

Signed-off-by: Mike Christie 
Signed-off-by: Nicholas Bellinger 
Signed-off-by: Greg Kroah-Hartman

be2iscsi: Fix kernel panic when device initialization fails

2015-04-19T08:11:09+00:00

commit 2e7cee027b26cbe7e6685a7a14bd2850bfe55d33 upstream.

Kernel panic was happening as iscsi_host_remove() was called on
a host which was not yet added.

Signed-off-by: John Soni Jose 
Reviewed-by: Mike Christie 
Signed-off-by: James Bottomley 
Signed-off-by: Greg Kroah-Hartman

n_tty: Fix read buffer overwrite when no newline

2015-04-19T08:11:08+00:00

commit fb5ef9e7da39968fec6d6f37f20a23d23740c75e upstream.

In canon mode, the read buffer head will advance over the buffer tail
if the input > 4095 bytes without receiving a line termination char.

Discard additional input until a line termination is received.
Before evaluating for overflow, the 'room' value is normalized for
I_PARMRK and 1 byte is reserved for line termination (even in !icanon
mode, in case the mode is switched). The following table shows the
transform:

 actual buffer |  'room' value before overflow calc
  space avail  |    !I_PARMRK    |    I_PARMRK
 --------------------------------------------------
      0        |       -1        |       -1
      1        |        0        |        0
      2        |        1        |        0
      3        |        2        |        0
      4+       |        3        |        1

When !icanon or when icanon and the read buffer contains newlines,
normalized 'room' values of -1 and 0 are clamped to 0, and
'overflow' is 0, so read_head is not adjusted and the input i/o loop
exits (setting no_room if called from flush_to_ldisc()). No input
is discarded since the reader does have input available to read
which ensures forward progress.

When icanon and the read buffer does not contain newlines and the
normalized 'room' value is 0, then overflow and room are reset to 1,
so that the i/o loop will process the next input char normally
(except for parity errors which are ignored). Thus, erasures, signalling
chars, 7-bit mode, etc. will continue to be handled properly.

If the input char processed was not a line termination char, then
the canon_head index will not have advanced, so the normalized 'room'
value will now be -1 and 'overflow' will be set, which indicates the
read_head can safely be reset, effectively erasing the last char
processed.

If the input char processed was a line termination, then the
canon_head index will have advanced, so 'overflow' is cleared to 0,
the read_head is not reset, and 'room' is cleared to 0, which exits
the i/o loop (because the reader now have input available to read
which ensures forward progress).

Note that it is possible for a line termination to be received, and
for the reader to copy the line to the user buffer before the
input i/o loop is ready to process the next input char. This is
why the i/o loop recomputes the room/overflow state with every
input char while handling overflow.

Finally, if the input data was processed without receiving
a line termination (so that overflow is still set), the pty
driver must receive a write wakeup. A pty writer may be waiting
to write more data in n_tty_write() but without unthrottling
here that wakeup will not arrive, and forward progress will halt.
(Normally, the pty writer is woken when the reader reads data out
of the buffer and more space become available).

Signed-off-by: Peter Hurley 
Signed-off-by: Greg Kroah-Hartman 
(backported from commit fb5ef9e7da39968fec6d6f37f20a23d23740c75e)
Signed-off-by: Joseph Salisbury

tty: serial: fsl_lpuart: clear receive flag on FIFO flush

2015-04-19T08:11:08+00:00

commit 8e4934c6d6c659e22b1b746af4196683e77ce6ca upstream.

When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.

Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.

Signed-off-by: Stefan Agner 
Signed-off-by: Greg Kroah-Hartman

usb: xhci: apply XHCI_AVOID_BEI quirk to all Intel xHCI controllers

2015-04-19T08:11:08+00:00

commit 227a4fd801c8a9fa2c4700ab98ec1aec06e3b44d upstream.

When a device with an isochronous endpoint is plugged into the Intel
xHCI host controller, and the driver submits multiple frames per URB,
the xHCI driver will set the Block Event Interrupt (BEI) flag on all
but the last TD for the URB. This causes the host controller to place
an event on the event ring, but not send an interrupt. When the last
TD for the URB completes, BEI is cleared, and we get an interrupt for
the whole URB.

However, under Intel xHCI host controllers, if the event ring is full
of events from transfers with BEI set,  an "Event Ring is Full" event
will be posted to the last entry of the event ring,  but no interrupt
is generated. Host will cease all transfer and command executions and
wait until software completes handling the pending events in the event
ring.  That means xHC stops, but event of "event ring is full" is not
notified. As the result, the xHC looks like dead to user.

This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And
it should be backported to kernels as old as 3.0, that contains the
commit 69e848c2090a ("Intel xhci: Support EHCI/xHCI port switching.").

Signed-off-by: Lu Baolu 
Tested-by: Alistair Grant 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: xhci: handle Config Error Change (CEC) in xhci driver

2015-04-19T08:11:08+00:00

commit 9425183d177aa4a2f09d01a74925124f0778b595 upstream.

Linux xHCI driver doesn't report and handle port cofig error change.
If Port Configure Error for root hub port occurs, CEC bit in PORTSC
would be set by xHC and remains 1. This happends when the root port
fails to configure its link partner, e.g. the port fails to exchange
port capabilities information using Port Capability LMPs.

Then the Port Status Change Events will be blocked until all status
change bits(CEC is one of the change bits) are cleared('0') (refer to
xHCI spec 4.19.2). Otherwise, the port status change event for this
root port will not be generated anymore, then root port would look
like dead for user and can't be recovered until a Host Controller
Reset(HCRST).

This patch is to check CEC bit in PORTSC in xhci_get_port_status()
and set a Config Error in the return status if CEC is set. This will
cause a ClearPortFeature request, where CEC bit is cleared in
xhci_clear_port_change_bit().

[The commit log is based on initial Marvell patch posted at
http://marc.info/?l=linux-kernel&m=142323612321434&w=2]

Reported-by: Gregory CLEMENT 
Signed-off-by: Lu Baolu 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

cpuidle: ACPI: do not overwrite name and description of C0

2015-04-19T08:11:08+00:00

commit c7e8bdf5872c5a8f5a6494e16fe839c38a0d3d3d upstream.

Fix a bug that leads to showing the name and description of C-state C0
as "" in sysfs after the ACPI C-states changed (e.g. after AC->DC
or DC->AC
transition).

The function poll_idle_init() in drivers/cpuidle/driver.c initializes the
state 0 during cpuidle_register_driver(), so we better do not overwrite it
again with '\0' during acpi_processor_cst_has_changed().

Signed-off-by: Thomas Schlichter 
Reviewed-by: Bartlomiej Zolnierkiewicz 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman