linux-stable.git/drivers/watchdog, branch v4.9.151

watchdog: sbsa: use 32-bit read for WCV

2018-05-30T05:50:34+00:00

[ Upstream commit 93ac3deb7c220cbcec032a967220a1f109d58431 ]

According to SBSA spec v3.1 section 5.3:
  All registers are 32 bits in size and should be accessed using
  32-bit reads and writes. If an access size other than 32 bits
  is used then the results are IMPLEMENTATION DEFINED.
  [...]
  The Generic Watchdog is little-endian

The current code uses readq to read the watchdog compare register
which does a 64-bit access. This fails on ThunderX2 which does not
implement 64-bit access to this register.

Fix this by using lo_hi_readq() that does two 32-bit reads.

Signed-off-by: Jayachandran C 
Reviewed-by: Guenter Roeck 
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

watchdog: f71808e_wdt: Fix magic close handling

2018-05-30T05:50:34+00:00

[ Upstream commit 7bd3e7b743956afbec30fb525bc3c5e22e3d475c ]

Watchdog close is "expected" when any byte is 'V' not just the last one.
Writing "V" to the device fails because the last byte is the end of string.

$ echo V > /dev/watchdog
f71808e_wdt: Unexpected close, not stopping watchdog!

Signed-off-by: Igor Pylypiv 
Reviewed-by: Guenter Roeck 
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

watchdog: sp5100_tco: Fix watchdog disable bit

2018-05-30T05:50:20+00:00

[ Upstream commit f541c09ebfc61697b586b38c9ebaf4b70defb278 ]

According to all published information, the watchdog disable bit for SB800
compatible controllers is bit 1 of PM register 0x48, not bit 2. For the
most part that doesn't matter in practice, since the bit has to be cleared
to enable watchdog address decoding, which is the default setting, but it
still needs to be fixed.

Cc: Zoltán Böszörményi 
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

watchdog: f71808e_wdt: Fix WD_EN register read

2018-04-24T07:34:14+00:00

commit 977f6f68331f94bb72ad84ee96b7b87ce737d89d upstream.

F71808FG_FLAG_WD_EN defines bit position, not a bitmask

Signed-off-by: Igor Pylypiv 
Reviewed-by: Guenter Roeck 
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

watchdog: f71808e_wdt: Add F71868 support

2018-04-13T17:48:20+00:00

[ Upstream commit 166fbcf88fdafa02f784ec25ac64745c716b2de0 ]

This adds support for watchdog part of Fintek F71868 Super I/O chip to
f71808e_wdt driver.

The F71868 chip is, in general, very similar to a F71869, however it has
slightly different set of available reset pulse widths.

Tested on MSI A55M-P33 motherboard.

Signed-off-by: Maciej S. Szmigiero 
Reviewed-by: Guenter Roeck 
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ACPI / watchdog: Fix off-by-one error at resource assignment

2018-03-28T16:39:22+00:00

commit b1abf6fc49829d89660c961fafe3f90f3d843c55 upstream.

The resource allocation in WDAT watchdog has off-one-by error, it sets
one byte more than the actual end address.  This may eventually lead
to unexpected resource conflicts.

Fixes: 058dfc767008 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Cc: 4.9+  # 4.9+
Signed-off-by: Takashi Iwai 
Acked-by: Mika Westerberg 
Acked-by: Guenter Roeck 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

watchdog: Fix potential kref imbalance when opening watchdog

2018-03-24T10:00:24+00:00

[ Upstream commit 4bcd615fad6adddc68b058d498b30a9e0e0db77a ]

If a watchdog driver's open function sets WDOG_HW_RUNNING with the
expectation that the watchdog can not be stopped, but then stops the
watchdog anyway in its stop function, kref_get() wil not be called in
watchdog_open(). If the watchdog then stops on close, WDOG_HW_RUNNING
will be cleared and kref_put() will be called, causing a kref imbalance.
As result the character device data structure will be released, which in
turn will cause the system to crash on the next call to watchdog_open().

Fixes: ee142889e32f5 ("watchdog: Introduce WDOG_HW_RUNNING flag")
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

watchdog: hpwdt: Remove legacy NMI sourcing.

2018-03-18T10:18:53+00:00

commit 2b3d89b402b085b08498e896c65267a145bed486 upstream.

Gen8 and prior Proliant systems supported the "CRU" interface
to firmware.  This interfaces allows linux to "call back" into firmware
to source the cause of an NMI.  This feature isn't fully utilized
as the actual source of the NMI isn't printed, the driver only
indicates that the source couldn't be determined when the call
fails.

With the advent of Gen9, iCRU replaces the CRU. The call back
feature is no longer available in firmware.  To be compatible and
not attempt to call back into firmware on system not supporting CRU,
the SMBIOS table is consulted to determine if it is safe to
make the call back or not.

This results in about half of the driver code being devoted
to either making CRU calls or determing if it is safe to make
CRU calls.  As noted, the driver isn't really using the results of
the CRU calls.

Furthermore, as a consequence of the Spectre security issue, the
BIOS/EFI calls are being wrapped into Spectre-disabling section.
Removing the call back in hpwdt_pretimeout assists in this effort.

As the CRU sourcing of the NMI isn't required for handling the
NMI and there are security concerns with making the call back, remove
the legacy (pre Gen9) NMI sourcing and the DMI code to determine if
the system had the CRU interface.

Signed-off-by: Jerry Hoemann 
Acked-by: Ingo Molnar 
Reviewed-by: Guenter Roeck 
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Signed-off-by: Greg Kroah-Hartman

watchdog: hpwdt: fix unused variable warning

2018-03-18T10:18:52+00:00

commit aeebc6ba88ba3758ad95467ff6191fabf2074c13 upstream.

The new hpwdt_my_nmi() function is used conditionally, which produces
a harmless warning in some configurations:

drivers/watchdog/hpwdt.c:478:12: error: 'hpwdt_my_nmi' defined but not used [-Werror=unused-function]

This moves it inside of the #ifdef that protects its caller, to silence
the warning.

Fixes: 621174a92851 ("watchdog: hpwdt: Check source of NMI")
Signed-off-by: Arnd Bergmann 
Reviewed-by: Jerry Hoemann 
Reviewed-by: Guenter Roeck 
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Signed-off-by: Greg Kroah-Hartman

watchdog: hpwdt: Check source of NMI

2018-03-18T10:18:52+00:00

commit 838534e50e2e5c1e644e30ab6cb28da88eb31368 upstream.

Do not claim the NMI (i.e. return NMI_DONE) if the source of
the NMI isn't the iLO watchdog or debug.

Signed-off-by: Jerry Hoemann 
Reviewed-by: Guenter Roeck 
Signed-off-by: Guenter Roeck 
Signed-off-by: Wim Van Sebroeck 
Signed-off-by: Greg Kroah-Hartman