The Cable PD Revision field in GET_CABLE_PROPERTY was
introduced in UCSI v2.1, so adding check for that.

The cable properties are also not used anywhere after the
cable is registered, so removing the cable_prop member
from struct ucsi_connector while at it.

Fixes: 38ca416597b0 ("usb: typec: ucsi: Register cables based on GET_CABLE_PROPERTY")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240903130945.3395291-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Partner PD Revision field in GET_CONNECTOR_CAPABILITY
data structure was introduced in UCSI v2.1. In
ucsi_check_connector_capability() the version was assumed to
be 2.0, and in ucsi_register_partner() the field is accessed
completely unconditionally.

Fixing the version in ucsi_check_connector_capability(), and
replacing the unconditional pd_revision assignment with a
direct call to ucsi_check_connector_capability() in
ucsi_register_port(). After this the revision is also
checked only if there is a PD contract.

Fixes: b9fccfdb4ebb ("usb: typec: ucsi: Get PD revision for partner")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240830111645.2134301-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Patch fixes the procedure of resetting controller.
The CPUCTRL register is write only and reading returns 0.
Waiting for reset to complite is incorrect.

Fixes: 3eb1f1efe204 ("usb: cdns2: Add main part of Cadence USBHS driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/PH7PR07MB9538D56D75F1F399D0BB96F0DD922@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This fix addresses STAR 9001285599, which only affects DWC_usb3 version
3.20a. The timer value for PM_LC_TIMER in DWC_usb3 3.20a for the Link
ECN changes is incorrect. If the PM TIMER ECN is enabled via GUCTL2[19],
the link compliance test (TD7.21) may fail. If the ECN is not enabled
(GUCTL2[19] = 0), the controller will use the old timer value (5us),
which is still acceptable for the link compliance test. Therefore, clear
GUCTL2[19] to pass the USB link compliance test: TD 7.21.

Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240829094502.26502-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When operating in High-Speed, it is observed that DSTS[USBLNKST] doesn't
update link state immediately after receiving the wakeup interrupt. Since
wakeup event handler calls the resume callbacks, there is a chance that
function drivers can perform an ep queue, which in turn tries to perform
remote wakeup from send_gadget_ep_cmd(STARTXFER). This happens because
DSTS[[21:18] wasn't updated to U0 yet, it's observed that the latency of
DSTS can be in order of milli-seconds. Hence avoid calling gadget_wakeup
during startxfer to prevent unnecessarily issuing remote wakeup to host.

Fixes: c36d8e947a56 ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: stable@vger.kernel.org
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240828064302.3796315-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 6.11-rc6.  Included in here are:

   - dwc3 driver fixes for reported issues

   - MAINTAINER file update, marking a driver as unsupported :(

   - cdnsp driver fixes

   - USB gadget driver fix

   - USB sysfs fix

   - other tiny fixes

   - new device ids for usb serial driver

  All of these have been in linux-next this week with no reported
  issues"

* tag 'usb-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: option: add MeiG Smart SRM825L
  usb: cdnsp: fix for Link TRB with TC
  usb: dwc3: st: add missing depopulate in probe error path
  usb: dwc3: st: fix probed platform device ref count on probe error path
  usb: dwc3: ep0: Don't reset resource alloc flag (including ep0)
  usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in remove_power_attributes()
  usb: typec: fsa4480: Relax CHIP_ID check
  usb: dwc3: xilinx: add missing depopulate in probe error path
  usb: dwc3: omap: add missing depopulate in probe error path
  dt-bindings: usb: microchip,usb2514: Fix reference USB device schema
  usb: gadget: uvc: queue pump work in uvcg_video_enable()
  cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI Controller
  usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq function
  usb: dwc3: core: Prevent USB core invalid event buffer address access
  MAINTAINERS: Mark UVC gadget driver as orphan

Johan writes:

USB-serial device id for 6.11-rc6

Here's a new modem device id.

This one has been in linux-next with no reported issues.

* tag 'usb-serial-6.11-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: option: add MeiG Smart SRM825L

Qualcomm driver fixes for v6.11

This corrects the tzmem virt-to-phys conversion, which caused issues for
the uefisecapp implementation of EFI variable access. SDM670 is excluded
from tzmem usage due to reported issues.

The SCM get wait queue context call is corrected to be marked ATOMIC and
some dead code in qseecom, following the tzmem conversion, is removed.

The memory backing command DB is remapped writecombined, to avoid XPU
violations when Linux runs without the Qualcomm hypervisor.

Two compile fixes are added for pd-mapper, and the broken reference
count is corrected, to make pd-mapper deal with remoteprocs going away.

In pmic_glink a race condition where the client callbacks might be
called before we returned the client handle is corrected. The broken conditions
for when to signal that the firmware is going down is also corrected.

In the pmic_glink UCSI driver, the ucsi_unregister() is moved out of the
pdr callback, as this is being invoked in atomic context.

Konrad's email address is updated in MAINTAINERS, and related mailmap
entries are added.

* tag 'qcom-drivers-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  soc: qcom: pd-mapper: Fix singleton refcount
  firmware: qcom: tzmem: disable sdm670 platform
  soc: qcom: pmic_glink: Actually communicate when remote goes down
  usb: typec: ucsi: Move unregister out of atomic section
  soc: qcom: pmic_glink: Fix race during initialization
  firmware: qcom: qseecom: remove unused functions
  firmware: qcom: tzmem: fix virtual-to-physical address conversion
  firmware: qcom: scm: Mark get_wq_ctx() as atomic call
  MAINTAINERS: Update Konrad Dybcio's email address
  mailmap: Add an entry for Konrad Dybcio
  soc: qcom: pd-mapper: mark qcom_pdm_domains as __maybe_unused
  soc: qcom: cmd-db: Map shared memory as WC, not WB
  soc: qcom: pd-mapper: Depend on ARCH_QCOM || COMPILE_TEST

Link: https://lore.kernel.org/r/20240826145209.1646159-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add support for MeiG Smart SRM825L which is based on Qualcomm 315 chip.

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  1
P:  Vendor=2dee ProdID=4d22 Rev= 4.14
S:  Manufacturer=MEIG
S:  Product=LTE-A Module
S:  SerialNumber=6f345e48
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms

Signed-off-by: ZHANG Yuntian <yt@radxa.com>
Link: https://lore.kernel.org/0041DFA5200EFB1B+20240803074619.563116-1-yt@radxa.com/
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

Stop Endpoint command on LINK TRB with TC bit set to 1 causes that
internal cycle bit can have incorrect state after command complete.
In consequence empty transfer ring can be incorrectly detected
when EP is resumed.
NOP TRB before LINK TRB avoid such scenario. Stop Endpoint command
is then on NOP TRB and internal cycle bit is not changed and have
correct value.

Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953878279F375CCCE6C6F40FDD8E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>