linux-stable.git/drivers/usb, branch v5.4.205

usb: chipidea: udc: check request status before setting device address

2022-06-29T06:58:47+00:00

commit b24346a240b36cfc4df194d145463874985aa29b upstream.

The complete() function may be called even though request is not
completed. In this case, it's necessary to check request status so
as not to set device address wrongly.

Fixes: 10775eb17bee ("usb: chipidea: udc: update gadget states according to ch9")
cc: 
Signed-off-by: Xu Yang 
Link: https://lore.kernel.org/r/20220623030242.41796-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman

xhci: turn off port power in shutdown

2022-06-29T06:58:47+00:00

commit 83810f84ecf11dfc5a9414a8b762c3501b328185 upstream.

If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.

During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.

Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add Quectel RM500K module support

2022-06-29T06:58:45+00:00

commit 15b694e96c31807d8515aacfa687a1e8a4fbbadc upstream.

Add usb product id of the Quectel RM500K module.

RM500K provides 2 mandatory interfaces to Linux host after enumeration.
 - /dev/ttyUSB5: this is a serial interface for control path. User needs
   to write AT commands to this device node to query status, set APN,
   set PIN code, and enable/disable the data connection to 5G network.
 - ethX: this is the data path provided as a RNDIS devices. After the
   data connection has been established, Linux host can access 5G data
   network via this interface.

"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs

usb-devices output for 0x7001:
T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=7001 Rev=00.01
S:  Manufacturer=MediaTek Inc.
S:  Product=USB DATA CARD
S:  SerialNumber=869206050009672
C:  #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Co-developed-by: Ballon Shi 
Signed-off-by: Ballon Shi 
Signed-off-by: Macpaul Lin 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add Quectel EM05-G modem

2022-06-29T06:58:45+00:00

commit 33b29dbb39bcbd0a96e440646396bbf670b914fa upstream.

The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:

"RMNET"	: AT + DIAG + NMEA + Modem + QMI
"MBIM"	: MBIM + AT + DIAG + NMEA + Modem

The detailed description of the USB configuration for each mode as follows:

RMNET Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030a Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

MBIM Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030a Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Yonglin Tan 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add Telit LE910Cx 0x1250 composition

2022-06-29T06:58:45+00:00

commit 342fc0c3b345525da21112bd0478a0dc741598ea upstream.

Add support for the following Telit LE910Cx composition:

0x1250: rmnet, tty, tty, tty, tty

Reviewed-by: Daniele Palmas 
Signed-off-by: Carlo Lobrano 
Link: https://lore.kernel.org/r/20220614075623.2392607-1-c.lobrano@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

usb: gadget: u_ether: fix regression in setting fixed MAC address

2022-06-25T10:44:35+00:00

commit b337af3a4d6147000b7ca6b3438bf5c820849b37 upstream.

In systemd systems setting a fixed MAC address through
the "dev_addr" module argument fails systematically.
When checking the MAC address after the interface is created
it always has the same but different MAC address to the one
supplied as argument.

This is partially caused by systemd which by default will
set an internally generated permanent MAC address for interfaces
that are marked as having a randomly generated address.

Commit 890d5b40908bfd1a ("usb: gadget: u_ether: fix race in
setting MAC address in setup phase") didn't take into account
the fact that the interface must be marked as having a set
MAC address when it's set as module argument.

Fixed by marking the interface with NET_ADDR_SET when
the "dev_addr" module argument is supplied.

Fixes: 890d5b40908bfd1a ("usb: gadget: u_ether: fix race in setting MAC address in setup phase")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca 
Link: https://lore.kernel.org/r/20220603153459.32722-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman

usb: gadget: lpc32xx_udc: Fix refcount leak in lpc32xx_udc_probe

2022-06-22T12:11:23+00:00

commit 4757c9ade34178b351580133771f510b5ffcf9c8 upstream.

of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() will check NULL pointer.

Fixes: 24a28e428351 ("USB: gadget driver for LPC32xx")
Cc: stable 
Signed-off-by: Miaoqian Lin 
Link: https://lore.kernel.org/r/20220603140246.64529-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Fix memory leak in dwc2_hcd_init

2022-06-22T12:11:23+00:00

commit 3755278f078460b021cd0384562977bf2039a57a upstream.

usb_create_hcd will alloc memory for hcd, and we should
call usb_put_hcd to free it when platform_get_resource()
fails to prevent memory leak.
goto error2 label instead error1 to fix this.

Fixes: 856e6e8e0f93 ("usb: dwc2: check return value after calling platform_get_resource()")
Cc: stable 
Acked-by: Minas Harutyunyan 
Signed-off-by: Miaoqian Lin 
Link: https://lore.kernel.org/r/20220530085413.44068-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman

USB: serial: io_ti: add Agilent E5805A support

2022-06-22T12:11:23+00:00

commit 908e698f2149c3d6a67d9ae15c75545a3f392559 upstream.

Add support for Agilent E5805A (rebranded ION Edgeport/4) to io_ti.

Signed-off-by: Robert Eckelmann 
Link: https://lore.kernel.org/r/20220521230808.30931eca@octoberrain
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add support for Cinterion MV31 with new baseline

2022-06-22T12:11:23+00:00

commit 158f7585bfcea4aae0ad4128d032a80fec550df1 upstream.

Adding support for Cinterion device MV31 with Qualcomm
new baseline. Use different PIDs to separate it from
previous base line products.
All interfaces settings keep same as previous.

Below is test evidence:
T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00b8 Rev=04.14
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00B8 USB Mobile Broadband
S:  SerialNumber=90418e79
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  7 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00b9 Rev=04.14
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00B9 USB Mobile Broadband
S:  SerialNumber=90418e79
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option

For PID 00b8, interface 3 is GNSS port which don't use serial driver.

Signed-off-by: Slark Xiao 
Link: https://lore.kernel.org/r/20220601034740.5438-1-slark_xiao@163.com
[ johan: rename defines using a "2" infix ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman