linux-stable.git/drivers/usb, branch v5.4.178 Linux kernel stable tree ucsi_ccg: Check DEV_INT bit only when starting CCG4 2022-02-01T16:24:35+00:00 Sing-Han Chen singhanc@nvidia.com 2022-01-12T09:41:43+00:00 5ede72d48cab2d57c37c7e3e75b47459a8c0cbfa commit 825911492eb15bf8bb7fb94bc0c0421fe7a6327d upstream. CCGx clears Bit 0:Device Interrupt in the INTR_REG if CCGx is reset successfully. However, there might be a chance that other bits in INTR_REG are not cleared due to internal data queued in PPM. This case misleads the driver that CCGx reset failed. The commit checks bit 0 in INTR_REG and ignores other bits. The ucsi driver would reset PPM later. Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx") Cc: stable@vger.kernel.org Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Sing-Han Chen <singhanc@nvidia.com> Signed-off-by: Wayne Chang <waynec@nvidia.com> Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 825911492eb15bf8bb7fb94bc0c0421fe7a6327d upstream.

CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.

The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.

Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: typec: tcpm: Do not disconnect while receiving VBUS off 2022-02-01T16:24:35+00:00 Badhri Jagan Sridharan badhri@google.com 2022-01-22T01:55:19+00:00 3922b6e1c9eaa545cbd448cd0bffaa43456b3576 commit 90b8aa9f5b09edae6928c0561f933fec9f7a9987 upstream. With some chargers, vbus might momentarily raise above VSAFE5V and fall back to 0V before tcpm gets to read port->tcpc->get_vbus. This will will report a VBUS off event causing TCPM to transition to SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state. Stub from the spec: "4.5.2.2.4.2 Exiting from AttachWait.SNK State A Sink shall transition to Unattached.SNK when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce. A DRP shall transition to Unattached.SRC when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce." [23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected] [23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS] [23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS] [23.300579] VBUS off [23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS] [23.301014] VBUS VSAFE0V [23.301111] Start toggling Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)") Cc: stable@vger.kernel.org Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 90b8aa9f5b09edae6928c0561f933fec9f7a9987 upstream.

With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.

Stub from the spec:
    "4.5.2.2.4.2 Exiting from AttachWait.SNK State
    A Sink shall transition to Unattached.SNK when the state of both
    the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
    A DRP shall transition to Unattached.SRC when the state of both
    the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."

[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling

Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: core: Fix hang in usb_kill_urb by adding memory barriers 2022-02-01T16:24:35+00:00 Alan Stern stern@rowland.harvard.edu 2022-01-24T20:23:45+00:00 9c61fce322ac2ef7fecf025285353570d60e41d6 commit 26fbe9772b8c459687930511444ce443011f86bf upstream. The syzbot fuzzer has identified a bug in which processes hang waiting for usb_kill_urb() to return. It turns out the issue is not unlinking the URB; that works just fine. Rather, the problem arises when the wakeup notification that the URB has completed is not received. The reason is memory-access ordering on SMP systems. In outline form, usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on different CPUs perform the following actions: CPU 0 CPU 1 ---------------------------- --------------------------------- usb_kill_urb(): __usb_hcd_giveback_urb(): ... ... atomic_inc(&urb->reject); atomic_dec(&urb->use_count); ... ... wait_event(usb_kill_urb_queue, atomic_read(&urb->use_count) == 0); if (atomic_read(&urb->reject)) wake_up(&usb_kill_urb_queue); Confining your attention to urb->reject and urb->use_count, you can see that the overall pattern of accesses on CPU 0 is: write urb->reject, then read urb->use_count; whereas the overall pattern of accesses on CPU 1 is: write urb->use_count, then read urb->reject. This pattern is referred to in memory-model circles as SB (for "Store Buffering"), and it is well known that without suitable enforcement of the desired order of accesses -- in the form of memory barriers -- it is entirely possible for one or both CPUs to execute their reads ahead of their writes. The end result will be that sometimes CPU 0 sees the old un-decremented value of urb->use_count while CPU 1 sees the old un-incremented value of urb->reject. Consequently CPU 0 ends up on the wait queue and never gets woken up, leading to the observed hang in usb_kill_urb(). The same pattern of accesses occurs in usb_poison_urb() and the failure pathway of usb_hcd_submit_urb(). The problem is fixed by adding suitable memory barriers. To provide proper memory-access ordering in the SB pattern, a full barrier is required on both CPUs. The atomic_inc() and atomic_dec() accesses themselves don't provide any memory ordering, but since they are present, we can use the optimized smp_mb__after_atomic() memory barrier in the various routines to obtain the desired effect. This patch adds the necessary memory barriers. CC: <stable@vger.kernel.org> Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 26fbe9772b8c459687930511444ce443011f86bf upstream.

The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return.  It turns out the issue is not unlinking
the URB; that works just fine.  Rather, the problem arises when the
wakeup notification that the URB has completed is not received.

The reason is memory-access ordering on SMP systems.  In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:

CPU 0					CPU 1
----------------------------		---------------------------------
usb_kill_urb():				__usb_hcd_giveback_urb():
  ...					  ...
  atomic_inc(&urb->reject);		  atomic_dec(&urb->use_count);
  ...					  ...
  wait_event(usb_kill_urb_queue,
	atomic_read(&urb->use_count) == 0);
					  if (atomic_read(&urb->reject))
						wake_up(&usb_kill_urb_queue);

Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:

	write urb->reject, then read urb->use_count;

whereas the overall pattern of accesses on CPU 1 is:

	write urb->use_count, then read urb->reject.

This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes.  The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject.  Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().

The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().

The problem is fixed by adding suitable memory barriers.  To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs.  The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.

This patch adds the necessary memory barriers.

CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: f_sourcesink: Fix isoc transfer for USB_SPEED_SUPER_PLUS 2022-02-01T16:24:35+00:00 Pavankumar Kondeti quic_pkondeti@quicinc.com 2022-01-22T03:03:22+00:00 4fc6519bdecb051afb0d2010e6f548d27830c4c3 commit 904edf8aeb459697129be5fde847e2a502f41fd9 upstream. Currently when gadget enumerates in super speed plus, the isoc endpoint request buffer size is not calculated correctly. Fix this by checking the gadget speed against USB_SPEED_SUPER_PLUS and update the request buffer size. Fixes: 90c4d05780d4 ("usb: fix various gadgets null ptr deref on 10gbps cabling.") Cc: stable <stable@vger.kernel.org> Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com> Link: https://lore.kernel.org/r/1642820602-20619-1-git-send-email-quic_pkondeti@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 904edf8aeb459697129be5fde847e2a502f41fd9 upstream.

Currently when gadget enumerates in super speed plus, the isoc
endpoint request buffer size is not calculated correctly. Fix
this by checking the gadget speed against USB_SPEED_SUPER_PLUS
and update the request buffer size.

Fixes: 90c4d05780d4 ("usb: fix various gadgets null ptr deref on 10gbps cabling.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1642820602-20619-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: common: ulpi: Fix crash in ulpi_match() 2022-02-01T16:24:35+00:00 Jon Hunter jonathanh@nvidia.com 2022-01-17T15:00:39+00:00 64e671a2216317502dfdfeb36c08eb44daa79916 commit 2e3dd4a6246945bf84ea6f478365d116e661554c upstream. Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash on the Tegra20 Ventana platform in the ulpi_match() function. The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS, registers a ulpi_driver but this driver does not provide an 'id_table', so when ulpi_match() is called on the Tegra20 Ventana platform, it crashes when attempting to deference the id_table pointer which is not valid. The Qualcomm USB HS PHY driver uses device-tree for matching the ULPI driver with the device and so fix this crash by using device-tree for matching if the id_table is not valid. Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2e3dd4a6246945bf84ea6f478365d116e661554c upstream.

Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.

The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.

Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-storage: Add unusual-devs entry for VL817 USB-SATA bridge 2022-02-01T16:24:35+00:00 Alan Stern stern@rowland.harvard.edu 2022-01-24T20:14:40+00:00 d66dc656c5f9f553ff31549551f3b5132db02cb4 commit 5b67b315037250a61861119683e7fcb509deea25 upstream. Two people have reported (and mentioned numerous other reports on the web) that VIA's VL817 USB-SATA bridge does not work with the uas driver. Typical log messages are: [ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD [ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00 [ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd [ 3606.328584] scsi host14: uas_eh_device_reset_handler success Surprisingly, the devices do seem to work okay for some other people. The cause of the differing behaviors is not known. In the hope of getting the devices to work for the most users, even at the possible cost of degraded performance for some, this patch adds an unusual_devs entry for the VL817 to block it from binding to the uas driver by default. Users will be able to override this entry by means of a module parameter, if they want. CC: <stable@vger.kernel.org> Reported-by: DocMAX <mail@vacharakis.de> Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5b67b315037250a61861119683e7fcb509deea25 upstream.

Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver.  Typical log messages are:

[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success

Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.

In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default.  Users will be able to override this entry by means
of a module parameter, if they want.

CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: hub: Add delay for SuperSpeed hub resume to let links transit to U0 2022-01-27T08:19:44+00:00 Kai-Heng Feng kai.heng.feng@canonical.com 2021-12-15T12:01:06+00:00 46fdba26cdff8d2795c3b7922deba9359bd0c6f7 [ Upstream commit 00558586382891540c59c9febc671062425a6e47 ] When a new USB device gets plugged to nested hubs, the affected hub, which connects to usb 2-1.4-port2, doesn't report there's any change, hence the nested hubs go back to runtime suspend like nothing happened: [ 281.032951] usb usb2: usb wakeup-resume [ 281.032959] usb usb2: usb auto-resume [ 281.032974] hub 2-0:1.0: hub_resume [ 281.033011] usb usb2-port1: status 0263 change 0000 [ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000 [ 281.049797] usb 2-1: usb wakeup-resume [ 281.069800] usb 2-1: Waited 0ms for CONNECT [ 281.069810] usb 2-1: finish resume [ 281.070026] hub 2-1:1.0: hub_resume [ 281.070250] usb 2-1-port4: status 0203 change 0000 [ 281.070272] usb usb2-port1: resume, status 0 [ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000 [ 281.089813] usb 2-1.4: usb wakeup-resume [ 281.109792] usb 2-1.4: Waited 0ms for CONNECT [ 281.109801] usb 2-1.4: finish resume [ 281.109991] hub 2-1.4:1.0: hub_resume [ 281.110147] usb 2-1.4-port2: status 0263 change 0000 [ 281.110234] usb 2-1-port4: resume, status 0 [ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s [ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000 [ 281.110426] hub 2-1.4:1.0: hub_suspend [ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1 [ 281.130998] hub 2-1:1.0: hub_suspend [ 281.137788] usb 2-1: usb auto-suspend, wakeup 1 [ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000 [ 281.177828] usb 2-1: usb wakeup-resume [ 281.197839] usb 2-1: Waited 0ms for CONNECT [ 281.197850] usb 2-1: finish resume [ 281.197984] hub 2-1:1.0: hub_resume [ 281.198203] usb 2-1-port4: status 0203 change 0000 [ 281.198228] usb usb2-port1: resume, status 0 [ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000 [ 281.217835] usb 2-1.4: usb wakeup-resume [ 281.237834] usb 2-1.4: Waited 0ms for CONNECT [ 281.237845] usb 2-1.4: finish resume [ 281.237990] hub 2-1.4:1.0: hub_resume [ 281.238067] usb 2-1.4-port2: status 0263 change 0000 [ 281.238148] usb 2-1-port4: resume, status 0 [ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s [ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000 [ 281.238385] hub 2-1.4:1.0: hub_suspend [ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1 [ 281.258076] hub 2-1:1.0: hub_suspend [ 281.265744] usb 2-1: usb auto-suspend, wakeup 1 [ 281.285976] hub 2-0:1.0: hub_suspend [ 281.285988] usb usb2: bus auto-suspend, wakeup 1 USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If the link is in a non-U0 state, then the device must transition the link to U0 prior to sending the remote wake message", but the hub only transits the link to U0 after signaling remote wakeup. So be more forgiving and use a 20ms delay to let the link transit to U0 for remote wakeup. Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 00558586382891540c59c9febc671062425a6e47 ]

When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[  281.032951] usb usb2: usb wakeup-resume
[  281.032959] usb usb2: usb auto-resume
[  281.032974] hub 2-0:1.0: hub_resume
[  281.033011] usb usb2-port1: status 0263 change 0000
[  281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.049797] usb 2-1: usb wakeup-resume
[  281.069800] usb 2-1: Waited 0ms for CONNECT
[  281.069810] usb 2-1: finish resume
[  281.070026] hub 2-1:1.0: hub_resume
[  281.070250] usb 2-1-port4: status 0203 change 0000
[  281.070272] usb usb2-port1: resume, status 0
[  281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[  281.089813] usb 2-1.4: usb wakeup-resume
[  281.109792] usb 2-1.4: Waited 0ms for CONNECT
[  281.109801] usb 2-1.4: finish resume
[  281.109991] hub 2-1.4:1.0: hub_resume
[  281.110147] usb 2-1.4-port2: status 0263 change 0000
[  281.110234] usb 2-1-port4: resume, status 0
[  281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[  281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.110426] hub 2-1.4:1.0: hub_suspend
[  281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[  281.130998] hub 2-1:1.0: hub_suspend
[  281.137788] usb 2-1: usb auto-suspend, wakeup 1
[  281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.177828] usb 2-1: usb wakeup-resume
[  281.197839] usb 2-1: Waited 0ms for CONNECT
[  281.197850] usb 2-1: finish resume
[  281.197984] hub 2-1:1.0: hub_resume
[  281.198203] usb 2-1-port4: status 0203 change 0000
[  281.198228] usb usb2-port1: resume, status 0
[  281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[  281.217835] usb 2-1.4: usb wakeup-resume
[  281.237834] usb 2-1.4: Waited 0ms for CONNECT
[  281.237845] usb 2-1.4: finish resume
[  281.237990] hub 2-1.4:1.0: hub_resume
[  281.238067] usb 2-1.4-port2: status 0263 change 0000
[  281.238148] usb 2-1-port4: resume, status 0
[  281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[  281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.238385] hub 2-1.4:1.0: hub_suspend
[  281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[  281.258076] hub 2-1:1.0: hub_suspend
[  281.265744] usb 2-1: usb auto-suspend, wakeup 1
[  281.285976] hub 2-0:1.0: hub_suspend
[  281.285988] usb usb2: bus auto-suspend, wakeup 1

USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.

So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: uhci: add aspeed ast2600 uhci support 2022-01-27T08:19:42+00:00 Neal Liu neal_liu@aspeedtech.com 2021-11-26T10:00:21+00:00 3ad5c9e502639570c5bfcef5b5e7a66aa8f05c8d [ Upstream commit 554abfe2eadec97d12c71d4a69da1518478f69eb ] Enable ast2600 uhci quirks. Signed-off-by: Neal Liu <neal_liu@aspeedtech.com> Link: https://lore.kernel.org/r/20211126100021.2331024-1-neal_liu@aspeedtech.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 554abfe2eadec97d12c71d4a69da1518478f69eb ]

Enable ast2600 uhci quirks.

Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20211126100021.2331024-1-neal_liu@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: gadget: f_fs: Use stream_open() for endpoint files 2022-01-27T08:19:41+00:00 Pavankumar Kondeti quic_pkondeti@quicinc.com 2021-11-12T10:24:40+00:00 0cba42c09ac8b5bcf8e2c83e7eaace012ecf545a [ Upstream commit c76ef96fc00eb398c8fc836b0eb2f82bcc619dc7 ] Function fs endpoint file operations are synchronized via an interruptible mutex wait. However we see threads that do ep file operations concurrently are getting blocked for the mutex lock in __fdget_pos(). This is an uninterruptible wait and we see hung task warnings and kernel panic if hung_task_panic systcl is enabled if host does not send/receive the data for long time. The reason for threads getting blocked in __fdget_pos() is due to the file position protection introduced by the commit 9c225f2655e3 ("vfs: atomic f_pos accesses as per POSIX"). Since function fs endpoint files does not have the notion of the file position, switch to the stream mode. This will bypass the file position mutex and threads will be blocked in interruptible state for the function fs mutex. It should not affects user space as we are only changing the task state changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting for the USB transfers to be finished. However there is a slight change to the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also getting blocked inside fdget_pos(). Now they reach to function fs and error code is returned. The non blocking behavior is actually honoured now. Reviewed-by: John Keeping <john@metanate.com> Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com> Link: https://lore.kernel.org/r/1636712682-1226-1-git-send-email-quic_pkondeti@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit c76ef96fc00eb398c8fc836b0eb2f82bcc619dc7 ]

Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.

The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655e3
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.

It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.

Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1636712682-1226-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: ftdi-elan: fix memory leak on device disconnect 2022-01-27T08:19:34+00:00 Wei Yongjun weiyongjun1@huawei.com 2021-12-17T08:34:28+00:00 1b10eb460dc161c7baec6907d7912d27e109a8e8 [ Upstream commit 1646566b5e0c556f779180a8514e521ac735de1e ] 'ftdi' is alloced when probe device, but not free on device disconnect, this cause a memory leak as follows: unreferenced object 0xffff88800d584000 (size 8400): comm "kworker/0:2", pid 3809, jiffies 4295453055 (age 13.784s) hex dump (first 32 bytes): 00 40 58 0d 80 88 ff ff 00 40 58 0d 80 88 ff ff .@X......@X..... 00 00 00 00 00 00 00 00 00 00 00 00 ad 4e ad de .............N.. backtrace: [<000000000d47f947>] kmalloc_order_trace+0x19/0x110 mm/slab_common.c:960 [<000000008548ac68>] ftdi_elan_probe+0x8c/0x880 drivers/usb/misc/ftdi-elan.c:2647 [<000000007f73e422>] usb_probe_interface+0x31b/0x800 drivers/usb/core/driver.c:396 [<00000000fe8d07fc>] really_probe+0x299/0xc30 drivers/base/dd.c:517 [<0000000005da7d32>] __driver_probe_device+0x357/0x500 drivers/base/dd.c:751 [<000000003c2c9579>] driver_probe_device+0x4e/0x140 drivers/base/dd.c:781 Fix it by freeing 'ftdi' after nobody use it. Fixes: a5c66e4b2418 ("USB: ftdi-elan: client driver for ELAN Uxxx adapters") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20211217083428.2441-1-weiyongjun1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 1646566b5e0c556f779180a8514e521ac735de1e ]

'ftdi' is alloced when probe device, but not free on device disconnect,
this cause a memory leak as follows:

unreferenced object 0xffff88800d584000 (size 8400):
  comm "kworker/0:2", pid 3809, jiffies 4295453055 (age 13.784s)
  hex dump (first 32 bytes):
    00 40 58 0d 80 88 ff ff 00 40 58 0d 80 88 ff ff  .@X......@X.....
    00 00 00 00 00 00 00 00 00 00 00 00 ad 4e ad de  .............N..
  backtrace:
    [<000000000d47f947>] kmalloc_order_trace+0x19/0x110 mm/slab_common.c:960
    [<000000008548ac68>] ftdi_elan_probe+0x8c/0x880 drivers/usb/misc/ftdi-elan.c:2647
    [<000000007f73e422>] usb_probe_interface+0x31b/0x800 drivers/usb/core/driver.c:396
    [<00000000fe8d07fc>] really_probe+0x299/0xc30 drivers/base/dd.c:517
    [<0000000005da7d32>] __driver_probe_device+0x357/0x500 drivers/base/dd.c:751
    [<000000003c2c9579>] driver_probe_device+0x4e/0x140 drivers/base/dd.c:781

Fix it by freeing 'ftdi' after nobody use it.

Fixes: a5c66e4b2418 ("USB: ftdi-elan: client driver for ELAN Uxxx adapters")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20211217083428.2441-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>