linux-stable.git/drivers/usb, branch v5.2.10

usb: setup authorized_default attributes using usb_bus_notify

2019-08-25T14:10:35+00:00

commit 27709ae4e2fe6cf7da2ae45e718e190c5433342b upstream.

Currently, the authorized_default and interface_authorized_default
attributes for HCD are set up after the uevent has been sent to userland.
This creates a race condition where userland may fail to access this
file when processing the event. Move the appending of these attributes
earlier relying on the usb_bus_notify dispatcher.

Signed-off-by: Thiébaud Weksteen 
Cc: stable 
Link: https://lore.kernel.org/r/20190806110050.38918-1-tweek@google.com
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: Add Motorola modem UARTs

2019-08-25T14:10:35+00:00

commit 6caf0be40a707689e8ff8824fdb96ef77685b1ba upstream.

On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams .

As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold .

The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork .

However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.

The ttyUSB ports on Droid 4 are:

ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable

The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.

To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.

The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.

The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.

The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.

Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.

I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.

After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=2a70 Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=88(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=8b(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8c(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=08(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=8d(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

In 22b8:900e "qc_dload" mode the device shows up as:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=900e Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

And in 22b8:4281 "ram_downloader" mode the device shows up as:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=4281 Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

Cc: Bjørn Mork 
Cc: Dan Williams 
Cc: Lars Melin 
Cc: Marcel Partap 
Cc: Merlijn Wajer 
Cc: Michael Scott 
Cc: NeKit 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Tested-by: Pavel Machek 
Signed-off-by: Tony Lindgren 
Cc: stable 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add the BroadMobi BM818 card

2019-08-25T14:10:35+00:00

commit e5d8badf37e6b547842f2fcde10361b29e08bd36 upstream.

Add a VID:PID for the BroadMobi BM818 M.2 card

T:  Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2020 ProdID=2060 Rev=00.00
S:  Manufacturer=Qualcomm, Incorporated
S:  Product=Qualcomm CDMA Technologies MSM
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

Signed-off-by: Bob Ham 
Signed-off-by: Angus Ainslie (Purism) 
Cc: stable 
[ johan: use USB_DEVICE_INTERFACE_CLASS() ]
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: Add support for ZTE MF871A

2019-08-25T14:10:35+00:00

commit 7e7ae38bf928c5cfa6dd6e9a2cf8b42c84a27c92 upstream.

This patch adds support for MF871A USB modem (aka Speed USB STICK U03)
to option driver. This modem is manufactured by ZTE corporation, and
sold by KDDI.

Interface layout:
0: AT
1: MODEM

usb-devices output:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  9 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1481 Rev=52.87
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE Technologies MSM
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option

Co-developed-by: Hiroyuki Yamamoto 
Signed-off-by: Hiroyuki Yamamoto 
Signed-off-by: Yoshiaki Okamoto 
Cc: stable 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add D-Link DWM-222 device ID

2019-08-25T14:10:35+00:00

commit 552573e42aab5f75aff9bab855a9677979d9a7d5 upstream.

Add device id for D-Link DWM-222 A2.

MI_00 D-Link HS-USB Diagnostics
MI_01 D-Link HS-USB Modem
MI_02 D-Link HS-USB AT Port
MI_03 D-Link HS-USB NMEA
MI_04 D-Link HS-USB WWAN Adapter (qmi_wwan)
MI_05 USB Mass Storage Device

Cc: stable@vger.kernel.org
Signed-off-by: Rogan Dawes 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: CDC: fix sanity checks in CDC union parser

2019-08-25T14:10:35+00:00

commit 54364278fb3cabdea51d6398b07c87415065b3fc upstream.

A few checks checked for the size of the pointer to a structure
instead of the structure itself. Copy & paste issue presumably.

Fixes: e4c6fb7794982 ("usbnet: move the CDC parser into USB core")
Cc: stable 
Reported-by: syzbot+45a53506b65321c1fe91@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum 
Link: https://lore.kernel.org/r/20190813093541.18889-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman

usb: cdc-acm: make sure a refcount is taken early enough

2019-08-25T14:10:35+00:00

commit c52873e5a1ef72f845526d9f6a50704433f9c625 upstream.

destroy() will decrement the refcount on the interface, so that
it needs to be taken so early that it never undercounts.

Fixes: 7fb57a019f94e ("USB: cdc-acm: Fix potential deadlock (lockdep warning)")
Cc: stable 
Reported-and-tested-by: syzbot+1b2449b7b5dc240d107a@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum 
Link: https://lore.kernel.org/r/20190808142119.7998-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman

usb: gadget: udc: renesas_usb3: Fix sysfs interface of "role"

2019-08-25T14:10:34+00:00

commit 5dac665cf403967bb79a7aeb8c182a621fe617ff upstream.

Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().

Fixes: cc995c9ec118 ("usb: gadget: udc: renesas_usb3: add support for usb role swap")
Cc:  # v4.12+
Reviewed-by: Geert Uytterhoeven 
Signed-off-by: Yoshihiro Shimoda 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

USB: core: Fix races in character device registration and deregistraion

2019-08-25T14:10:34+00:00

commit 303911cfc5b95d33687d9046133ff184cf5043ff upstream.

The syzbot fuzzer has found two (!) races in the USB character device
registration and deregistration routines.  This patch fixes the races.

The first race results from the fact that usb_deregister_dev() sets
usb_minors[intf->minor] to NULL before calling device_destroy() on the
class device.  This leaves a window during which another thread can
allocate the same minor number but will encounter a duplicate name
error when it tries to register its own class device.  A typical error
message in the system log would look like:

    sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0'

The patch fixes this race by destroying the class device first.

The second race is in usb_register_dev().  When that routine runs, it
first allocates a minor number, then drops minor_rwsem, and then
creates the class device.  If the device creation fails, the minor
number is deallocated and the whole routine returns an error.  But
during the time while minor_rwsem was dropped, there is a window in
which the minor number is allocated and so another thread can
successfully open the device file.  Typically this results in
use-after-free errors or invalid accesses when the other thread closes
its open file reference, because the kernel then tries to release
resources that were already deallocated when usb_register_dev()
failed.  The patch fixes this race by keeping minor_rwsem locked
throughout the entire routine.

Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com
Signed-off-by: Alan Stern 
CC: 
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman

usb: typec: tcpm: Ignore unsupported/unknown alternate mode requests

2019-08-16T08:10:57+00:00

commit 88d02c9ba2e83fc22d37ccb1f11c62ea6fc9ae50 upstream.

TCPM may receive PD messages associated with unknown or unsupported
alternate modes. If that happens, calls to typec_match_altmode()
will return NULL. The tcpm code does not currently take this into
account. This results in crashes.

Unable to handle kernel NULL pointer dereference at virtual address 000001f0
pgd = 41dad9a1
[000001f0] *pgd=00000000
Internal error: Oops: 5 [#1] THUMB2
Modules linked in: tcpci tcpm
CPU: 0 PID: 2338 Comm: kworker/u2:0 Not tainted 5.1.18-sama5-armv7-r2 #6
Hardware name: Atmel SAMA5
Workqueue: 2-0050 tcpm_pd_rx_handler [tcpm]
PC is at typec_altmode_attention+0x0/0x14
LR is at tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm]
...
[] (typec_altmode_attention) from []
				(tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm])
[] (tcpm_pd_rx_handler [tcpm]) from []
				(process_one_work+0x123/0x2a8)
[] (process_one_work) from []
				(worker_thread+0xbd/0x3b0)
[] (worker_thread) from [] (kthread+0xcf/0xf4)
[] (kthread) from [] (ret_from_fork+0x11/0x38)

Ignore PD messages if the associated alternate mode is not supported.

Fixes: e9576fe8e605c ("usb: typec: tcpm: Support for Alternate Modes")
Cc: stable 
Reported-by: Douglas Gilbert 
Cc: Douglas Gilbert 
Acked-by: Heikki Krogerus 
Tested-by: Douglas Gilbert 
Signed-off-by: Guenter Roeck 
Link: https://lore.kernel.org/r/1564761822-13984-1-git-send-email-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman